Operation; Maintenance - Ryobi RBV-2200 Operator's Manual

OPERATION

Plug the Blower/Vac into the mains supply. The
■
LiveTool indicator(13) will light up.
Note: To reduce the risk of injury, safety switches are
installed for the nozzle and dust bag. The Blower/
Vac cannot be turned on unless the nozzle and
dust bag are attached.
OPERATING AS A BLOWER
Set the mode selection lever(11) to the position
■
showing the arrow pointing forward. Ensure the lever
has clicked to place and is rotated to the furthest point.
See Fig.5
Push the switch(3) to turn power on. See Fig.6
■
Hold the Blower/Vac as shown in Fig.7, and sweep
■
from side to side with the nozzle a few inches above
the ground or floor. Move the Blower/Vac slowly, while
accumulating a pile of debris.
Use the blower on walls as shown in Fig.8.
■
OPERATING AS A VACUUM
Set the mode selection lever(11) to the position
■
showing the arrow pointing backward. Ensure the lever
has clicked to place and is rotated to the furthest point.
See Fig.9
Make sure the dust bag is fitted properly.
■
Push the switch(3) to turn power on. See Fig.6
■
Position the suction mouth on the area to be cleared.
■
Hold the Blower/Vac with the nozzle close to ground
■
as shown in Fig.10, tilting the nozzle slightly, and use
a sweeping action to collect light debris. The debris
will flow in to the dust bag. Things such as leaves
and small twigs will be mulched as they pass through
the fan housing, allowing the dust bag to hold a lot of
debris.
When the dust bag gets full, suction will noticeably
■
decrease. Turn off and unplug the Blower/Vac before
emptying the dust bag.
WARNING
When the impeller in the motor housing is clogged
with twigs, nylon bags, etc. turn off and unplug
the Blower/Vac, remove the nozzle and then the
obstruction carefully.
SPEED CONTROL (RBV-2400VP ONLY)
The speed of the unit can be varied using the dial(4) in
front of the handle.
English
Rotate the dial anticlockwise to set higher speed and
■
clockwise for lower speed. See Fig.11
PATIO HEAD(9) (RBV-2400VP ONLY)
The patio head(9) increases the area of suction when the
unit is being used in vacuum mode.
Slot the patio head into the nozzle until it is fully in.
■
See Fig.12
Use the patio head wheels to roll the Blower/Vac over
■
the area being cleaned, in similar posture as for a
vacuum cleaner.
EMPTYING THE DUSTBAG
WARNING
Wear eye protection and face shield to limit your
exposure to dust and debris.
Turn off and unplug the Blower/Vac from the mains.
■
Empty the contents via the zip at the bottom of the
■
bag.
Alternatively, detach the dust bag from the motor
■
housing and empty through the top.
MAINTENANCE AND STORAGE
Take care of your machine and clean it regularly to
■
Obtain long-lasting efficiency and performance.
When you have finished work, remove the dust bag,
■
turn it upside down and clean it thoroughly.
Use only a warm damp cloth and soft brush to clean
■
your machine. Do not use petrol, turpentine, lacquer or
paint thinner, dry cleaning fluids or similar products.
If vacuum power decreases and the dust bag is empty,
■
clean the shredding chamber carefully.
Prior to storing your Blower / Vacuum after use, check
■
to ensure the product is not clogged with dirt or debris
and that the blow / vacuum mode selection lever is
operating smoothly. Keep all nuts, bolts and screws
tight to be sure your machine is in a safe working
condition. Use only Ryobi replacement parts and
accessories.
CLEANING THE DUST BAG
Empty the dust bag after each use to avoid
■
deterioration and obstruction of the air flow which will
reduce the performance of the unit.
Clean the dust bag as needed. With eye protection
■
on, turn the dust bag inside out after initial emptying
and vigorously shake out the dust and debris.
5

MAINTENANCE