Technics SL-PI 200 Operating Instructions Manual page 8

Front panel controls and their functions
0 Power switch
press (1-m
) to switch the power on.
Press again (m-l) to switch the power off.
63 Open button
Press this button to open the disc compartment
cow?r.
Close the cover by hand after loading a disc.
Note:
The oover does not open if this button is pressed during
the following operating modes:
1. While disc information is being read (disc ie
spinning).
2. During disc play.
3. While the unit is in the pause mode.
0 Insulator
(See page 26 for details.)
0 Disc compartment
The disc is inserted here with the label side up.
Q Control panel
m Forward and backward rocking/search
buttons
These buttons are used for the following search
operations.
H To move the pickup forward or backward by one
pit-track (rocking search play)
n To move the pickup forward or backward to a
desired point (search play).
(See page 17 for details.)
@ Forward and backward track skip buttons
These buttons are used to move the pickup to the
beginning of the next or previous track in the
forward or backward direction (skip play)
(See page 16 for details.)
aNumeric buttons
These buttons (O-S) are used for the following two
operations.
1. TO specify track numbers for program play or random
access play.
(See pages 12-15 for details.)
2. To specify a specific point on the disc as the diet play
starting time (min., sec., 0.1 set).
(See page 13 for details.)
aAsterisk (*) button
Press this button to eeparate track number, minutes,
and seconds when entering specific play starting time.
(See page 13 for details.)
0 Stop button
Press this button to stop play.
Press this button to stop play and cancel all previous
settings.
Note:
When this button is pressed, the player returne to the
stop mode.
the filet track and the display shows the total
-a-
0 Pause button/pause indicator
Press thie button to briefly stop play.
The pause indicator will illuminate.
TO continue play, press the play button.
The pause indicator will go out.
(See page 11 for details.)
Play is stopped, but the pickup remains where it
was at the time when the pause button was
The diet rotates while the unit is in the pause
m Play button/play indicator
Press thie button to begin play.
.I, presseo aur,ng play, me pIcKUp returns 10 me
beginning of the first track, playing the disc again.
*During program play, the pickup returns to the begin-
ning of the current track.
(Auto-return play function)
*The play indicator illuminates when the play button is
pressed and goes out when piay is stopped.
(See page 11 for details.)
a Time recall button
Press this button to confirm the disc play starting time
when playing a disc from a specific point.
(See page 13 for details.)
0 Memory button
Press thie button to enter displayed track numbers
into the memory.
*A maximum of 20 selections can be programmed.
*The letter " :z " will be displayed if you attempt to
enter more than 20 selections.
(See pages 14-15 details.)
@) Clear button
Press this button to clear individual program entries
before program play is started.
If this button is pressed during program play, the entire
program is cleared.
(See page 14 for details.)
m Recall button
Press this button to check the contents of a prog-
ram.
When this button is pressed, the programmed track
numbers are displayed one by one.
(See page 15 for details.)
Q Index button
Press this button to specify an index number.
(See page 12 for details.)
@ Auto space button/auto space indicator
Press this button to set a silent interval of 3 seconde
between the songs on a disc.
(The auto space indicator will illuminate.)
Press this button again to cancel the auto space
function.
(The indicator will go out.)
Note:
If auto space is used together with auto cue, only the
auto cue function will operate.
(See page 19 for details.)