Page 1
Retain it for future reference. Record model number and serial number of the set. See the label attached on the back of the set and quote this information to your dealer when you require service. MW-30LZ10 Model number : OWNER’S MANUAL Serial number :...
Page 2
Multimedia Display This LCD monitor can be connected to a PC in place of the PC Monitor. The LCD Display panel The panel is composed of 2.9 million individual cells and a few defective cells are likely to appear as coloured dots on the screen as a result of the manufacturing process.
Table of Contents First step Safety instructions ............4 Monitor Overview Front Panel Controls ..........12 Connection Panel Overview ........13 Remote Control Key Functions ......14 Accesories/Optional extra........16 Using the remote control ........17 Equipment Connections and Setup VCR Setup..............18 Cable TV Setup ............20 External AV Source Setup ........21 DVD Setup..............22 DTV Setup ..............23...
Safety Instructions - Use the Monitor at the place lower than the altitude of 6562 feet (2000m) to get the best quality of picture and sound. WARNING Do not place the Monitor in direct sunlight or near heat In the event of a lightning or thunder storm unplug sources such as heat registers, stove and so on.
Page 5
Safety instructions have two kinds of information, and each meaning of it is as below. The violation of this instruction may cause serious injuries and even death. WARNING The violation of this instruction may cause light injuries or damage of the NOTES product.
Page 6
Safety Instructions WARNING Do not use the Monitor in a damp place such as a bathroom where it is likely to get wet. - This may cause a fire or an electric shock hazard ! WARNING In case of using a receiver (VCR, In case of using a receiver Digital Set Top Box), do not place an (VCR, Digital Set Top Box),...
Page 7
WARNING In case of using a receiver (VCR, Digital Set Top Box), Bend antenna cable between inside and outside building to prevent rain from flowing in. - This may cause water damaged inside the Monitor and could give an electric shock. NOTES In case of using a receiver (VCR, Digital Set Top Box), there should be enough distance between an outside antenna and power lines to keep...
Page 8
Safety Instructions NOTES Hold the plug firmly when Prevent dust collecting on the unplugging. If you pull the power plug pins or outlet. cord the cord may be dam- - This may cause a fire hazard ! aged. - This may cause a fire hazard ! WARNING Do not place anything containing liquid on top of the monitor such as flowerpot, cup, cosmetics or candle.
Page 9
NOTES Do not plug when the power cord or the plug is Ensure the power cord does not come into contact with sharp or hot objects such damaged or the connecting part of the power outlet is loose. as a heater. - This may cause a fire or an electric shock hazard ! - This may cause a fire or an electric shock hazard ! NOTES...
Page 10
Safety Instructions WARNING In the event that an image does not appear on the screen please switch it off and unplug it from the mains suuply and contact your Service Centre. - This may cause a fire or an electric shock hazard ! WARNING In the unlikely event of smoke Do not use water while...
Page 11
WARNING NOTES Do not place heavy objects Do not watch the monitor while driving or on the Monitor. walking. - This may cause serious injury to - This may cause an accident. a child or adult. NOTES Contact the service center once a year to clean Unplug this product from the wall outlet the internal part of the monitor.
Front Panel Controls <Front Panel Controls> POWER INPUT MENU ON OFF SELECT Remote control sensor POWER INPUT MENU ON OFF SELECT Power standby indicator Illuminates orange in stand- by mode, Illuminates green when the Monitor is turned Main power button Sub power button MENU button INPUT SELECT button...
Connection Panel Overview <Back Panel> DC OUTPUT AUDIO L MONO VIDEO AC INPUT (DC 12V) S-VIDEO AUDIO RGB 2 INPUT RGB 1 INPUT RS 232C INPUT COMPONENT (DVD/DTV INPUT) AV INPUT (DIGITAL RGB INPUT) (PC/DTV INPUT) (CONTROL/SERVICE) AC INPUT jack DC OUTPUT (DC 12V) jack - The DC OUTPUT jack is Audio Input sound (R)(L)jacks...
Remote Control Key Functions - When using the remote control aim it at the remote control sensor on the Monitor. POWER POWER button SLEEP INPUT SELECT SLEEP button (Refer to p. 31) DASP APC button PIP ARC ARC button TWIN PICTURE PIP button SUB INPUT SWAP...
Page 15
input select button on the remote control Each press of this button changes the mode as shown below. RGB1 RGB2 COMPONENT INPUT SELECT button DASP button (Refer to p. 34) S-VIDEO VIDEO PIP ARC select button TWIN PICTURE button (Refer to p. 42~46) SUB INPUT button MUTE button switches the sound on or off.
Using the remote control Installing batteries • Open the battery compartment cover on the back of the remote control and insert the batteries with correct polarity, match “+” with “+”, and match “-” with “-”. • Install two 1.5V “AAA” alkaline batteries. Don’t mix used batteries with new batteries.
VCR Setup - As shown below, when connecting the Monitor to a VCR, match the colors of AV input jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) = white, Audio (Right) = red. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input of the Plasma Monitor.
DC OUTPUT AUDIO VIDEO L MONO AC INPUT (DC 12V) S-VIDEO RGB 2 INPUT RGB 1 INPUT RS 232C INPUT AUDIO COMPONENT (DVD/DTV INPUT) AV INPUT (DIGITAL RGB INPUT) (PC/DTV INPUT) (CONTROL/SERVICE) Back panel of the Monitor To watch VCR INPUT SELECT Press INPUT SELECT button on the remote control and select...
Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming without a TV tuner or cable TV converter box. AUDIO DC OUTPUT L MONO...
External AV Source Setup - As shown below, when connecting the Monitor to an external source, match the colors of AV input jacks on the Monitor with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red. AUDIO DC OUTPUT L MONO...
DVD Setup How to connect a DVD (digital video disk player) • Connect DVD video inputs to Y, P of COMPONENT (DVD/DTV INPUT) and audio inputs to Audio jacks of AV INPUT. • Component Input is available to 480i, 480p, 720p, 1080i mode. Back panel of the Monitor AUDIO L MONO...
DTV Setup - To watch digitally broadcast programs, purchase/connect a digital SET-TOP BOX. How to connect • You can use either the Monitor’s COMPONENT (DVD/DTV INPUT) inputs or the single RGB1(PC/DTV INPUT) for video connections, depending on your Set Top Box connectors. Then, make the corresponding Audio connections.
Connecting to a wireless trasmitter (option) • Only adjust this function in some models. • When connecting the wireless transmitter with external equipments, match the colors of connecting ports (Video - yellow, Audio(L) - white, Audio(R) -red). • If you have a mono VCR, connect the audio cable from the VCR to the AV input of the wireless AV transmitter.
Connecting to a wireless receiver (option) • Only adjust this function in some models. • When connecting the wireless receiver with external equipments, match the colors of con- necting ports (Video - yellow, Audio(L) - white, Audio(R) -red). Receiver rear AV INPUT 12V DC INPUT DC OUTPUT...
PC Setup - You can easily connect the Plasma Display to your PC for outstanding image and sound. Setup Instructions to Connect a PC to your Monitor • To setup this monitor in your PC window environ- • Connect the audio cable from the PC to the Audio ment, select Normal, Standard or Default Monitor.
Turning on the Monitor - When using the remote control, aim it at the sensor on the Monitor. Turning on the Monitor just after installation Connect power cord correctly. Press the main ON OFF button on the Monitor. At this moment, the Monitor is switched to standby mode.
Checking features - Use the remote control to make adjustments. - Select VIDEO input source. Press the MENU button. Press the UP/DOWN button. • Each press will cycle through the menus shown below. PICTURE SOUND DASP Contrast Treble Brightness Bass Color Balance Sharpness...
Setting Sleep Timer Sleep Timer turns the Monitor off after a preset time Press the SLEEP button to set sleep time. SLEEP Each time you press SLEEP button, the next pre- set setting time is changed as follows: SLEEP: • To release sleep time setting, press the SLEEP button repeatedly to select Tips •...
Auto picture control Use APC to set the Monitor for the best picture appearance APC (Auto Picture Control) Press the APC button. Press the APC or UP/DOWN buttons to select your desired picture condition. Clear Soft User User Adjust A Exit •...
Adjusting picture appearance Press the MENU button and then press the UP/DOWN button PICTURE to select menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Contrast and then press the VOL ( ) button. PICTURE Contrast Contrast Brightness...
Auto Sound Control DASP (Digital Auto Sound Processing) • This function lets you enjoy the best sound without any manual adjustment because the Monitor automatically selects the appropriate audio tone levels based on the program content. Press the DASP button. DASP Press the DASP or UP/DOWN button to select a sound setup.
Adjusting Sound Manual Settings Press the MENU button and then press the UP/DOWN button SOUND to select menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Treble and then press the VOL ( SOUND button. DASP Treble Treble...
Selecting language for the menus Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Language and then press the SPECIAL Language ENGLISH VOL ( ) button.
Adjusting color temperature Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Color TEMP. and then press the SPECIAL Language VOL ( ) button.
Using the Screen Saver function - Prolonged display of a still image may cause a permanent image to be ‘burnt’ on the screen - If you select Screen Saver "ON", to prevent the permanent image, the picture moves a little by the sequence of "Right-Bottom-Left-Up" every 10 minutes. - "SCREEN SAVER"...
Setting picture format - Wide and normal size are possible in RGB1(PC) and RGB2 mode, and Wide, normal and zoom size are possible in RGB1(DTV) mode. Press the ARC button to select a desired picture format. • Each time you press ARC buttons, you can select WIDE NORMAL ZOOM...
Using the Zoom in/out function Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Zoom In and then press the VOL ( ) button.
Moving the picture - Adjust the screen with ‘ZOOM IN/OUT’ function to use the ‘POSITION’ function. Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( ) button. MENU Press the UP/DOWN button to select Position and then press the VOL ( PICTURE ADJ.
Picture in picture (PIP) function PIP/TWIN PICTURE will let you view two seperate inputs on your monitor screen at the same time. Color of main picture may be different from PIP’s in PIP/TWIN PICTURE. When the main picture is RGB1/DTV(more than 480p), the sub picture is Input/S- video/DVD(480i) and when the main picture is Input / S- video / DVD(480i), the sub picture is RGB1 / DTV(more than 480p) / RGB2.
Page 43
Moving the sub picture Press the WIN. POSITION button in PIP. • Press the VOL( ) button and UP/DOWN button to adjust the position. WIN.POSITION Window Position Adjust Exit Change the main picture and the sub picture Press the SWAP button in PIP. SWAP VIDEO RGB1...
Zoom in/out main picture Viewing External Equipment Press the ZOOM+ button in PIP mode. ZOOM+ Zoom Pos.Adj. Exit • Enlarge the picture with ZOOM+ button. ‘ZOOM’ is possible to 50. • Press the ZOOM- button to reduce the zoom effect. Moving the enlarged picture Press the VOL button or...
Twin picture function How to use twin picture Press the TWIN PICTURE button to select desired twin picture. TWIN PICTURE • Each time you press TWIN PICTURE buttons, you can select TWIN1 TWIN2 TWIN OFF alternatively. TWIN1 TWIN2 TWIN OFF TWIN 1 TWIN 2 TWIN OFF...
Page 46
Twin picture function PIP/TWIN PICTURE let you view different inputs on your monitor screen at the same time. Color of main picture may be different from PIP’s in PIP/TWIN PICTURE. When the main picture is RGB1/DTV(more than 480p), the sub picture is Input/S- video/DVD(480i) and when the main picture is Input / S- video / DVD(480i), the sub picture is RGB1 / DTV(more than 480p) / RGB2.
Using the screen options - This function works in Video and S-video modes. - Use this option to correct trembling or picture instability while viewing a video tape. Press the MENU button and then press the UP/DOWN button to select PICTURE menu.
PC Mode Feature Check - Use the remote control to make adjustments. - Select RGB 1 input source. Press the MENU button. Press the UP/DOWN button. • Each press will cycle through the menus shown below. PICTURE SOUND DASP Contrast Treble Brightness Bass...
PC Mode Adjustment - This function works only in the RGB1 mode. Press the MENU button and then press the UP/DOWN button PICTURE ADJ. to select menu. Press the VOL ( ) button. MENU Use the UP/DOWN button to select Auto Config.
Page 50
PC Mode Adjustment Horizontal/Vertical position and CLOCK/PHASE adjustment work in RGB1(PC mode) and Horizontal/Vertical position only work in RGB(DTV mode-480p,720p,1080i). Press the MENU button and then press the UP/DOWN button to select PICTURE ADJ. menu. Press the VOL ( ) button. MENU Use the UP/DOWN button to select Clock Adjust...
External Control Device Setup Connect the RS-232C input jack to a PC and control the Monitor’s functions (such as ON/OFF, INPUT SELECT, MUTE) externally. How to connect external control equipment • Connect the RS-232C (serial connector) input jack with the rear of moniter’s RS-232C input jack.
External Control Device Setup SET ID • Use this function to specify a monitor ID number. Press the MENU button and then press the UP/DOWN button to select SPECIAL menu. Press the VOL ( ) button. MENU Use the UP/DOWN buttons to select Set ID and then press the VOL ( ) button.
Page 53
External Control Device Setup The RS-232C input jack is used to control the Monitor’s functions using an external control device. Type of connector : D-Sub 9-pin male Pin name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send)
Page 54
External Control Device Setup 01. Power (Command:p) G To control Power On/Off of the Monitor. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement Transmission / Receiving Protocol [a][ ][Set ID][ ][OK][Data][x] Data 0 : Power Off Transmission 1 : Power On [Command1][Command2][ ][Set ID][ ][Data][Cr]...
Page 55
03. Aspect Ratio (Command:c) 06. Volume control (Command:f) G To adjust the screen format. You can also adjust the screen format using the ARC G To adjust volume. button on remote control or in the Picture Adj. menu. You can also adjust volume with the VOL buttons on remote control.
Page 56
External Control Device Setup 12. OSD select (Command:l) 09. Color (Command:i) G To select OSD (On Screen Display) on/off. G To adjust the screen color. You can also adjust color in the Picture menu. Transmission Transmission [k][l][ ][Set ID][ ][Data][Cr] [k][i][ ][Set ID][ ][Data][Cr] Data 0 : OSD off 1 : OSD on...
Page 57
15. PIP size (Command:e) 17. Treble (Command:r) G To select PIP size. G To adjust the screen treble. Transmission You can also adjust treble in the sound menu. Transmission [k][o][ ][Set ID][ ][Data][Cr] Data 0 : Normal screen (4:3) [k][r][ ][Set ID][ ][Data][Cr] 1 : Wide screen (16:9) Data Min : 0 ~ Max : 64 Acknowledgement...
Page 58
External Control Device Setup 20. Color temperature (Command:u) 23. B-Adjust (Command:$) G To set up with ‘normal, cool, warm, user’ in the color G To adjust ‘B-adjust’ in the color temperature. temperature. Transmission Transmission [k][u][ ][Set ID][ ][Data][Cr] [k][$][ ][Set ID][ ][Data][Cr] Data 0 : Normal Data Min : 0 ~ Max : 64 1 : Cool...
Troubleshooting check list • Check whether the Monitor is turned on. No picture & • Power cord inserted into wall outlet? No sound • Plug another product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. •...
Page 60
Troubleshooting check list No output from one • Adjust Balance in the SOUND menu. (Refer to 35 page) of the speakers • This is normal as the image is muted during the startup Picture appears process of the monitor. slowly, after Please contact your service center, if the picture has not appeared after five minutes.