LCD MONITOR SERVICE MANUAL CHASSIS : MF-02HA MODEL : MW-30LZ10 CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. Aug., 2002 P/NO : 3828VD0120B Printed in Korea...
SAFETY PRECAUTIONS IMPORT ANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
ADJUSTMENT INSTRUCTION 1. Application Object 3-2. EDID (The Extended Display These instructions are applied to all of the MODELS of LCD Identification Data) Adjustment MONITOR, MF-02HA. (1) This is the function that is made for the realization of “Plug and Play” which makes possible to use the user environment right after reorganization by communicating with monitor automatically.
Page 5
(2) Connection Diagram of Equipment for Key and adjust it until color coordination becomes (B GAIN is fixed) Measuring (Automatic Adjustment) color coordination : X=0.283±0.003, Y=0.296±0.003 color temperature : 9,350°K ± 500°K COLOR ANALYZER TYPE;CA-100 (R Gain is used to adjust X-coordinates while adjusting and X-coordinates could be shortened when R Gain is RGB Signal Input High Light...
TROUBLESHOOTING Symptom Cause Check Point 1) Check BD801, Q801, Q802, Q804 1. No power from all outputs 1) Fuse open 2) Check BD801, L801, L802, TH800, TH801 2) Error of rectying circuit/EMI Filter 1) Check the second side parts and Pattern short 2.
2. System Block Diagram & Function 2-1. Input Source Ranges (1) Input Paths : CVBS, S-Video, Component (480i, 480p, 720p, 1080i), RGB 1, RGB 2, RS-232C (2) Video System Recognition (Multi-system ; Refer to Product Specification) : NTSC M, NTSC 4.43, PAL, PAL M, PAL N, PAL 4.43, SECAM (3) RGB 1 Mode Compatibility : Up to SXGA 75Hz (See Compatibility Table in Product Specification in detail.) (4) RGB 2 Mode Compatibility...
Page 14
3-1. Explanation of Circuit Movement If the AC Input voltage(1) is confirmed to power device, this Input voltage is adjusted as DC wave form through EMI FILTER(2) and the first adjusting part(3). This adjusted wave form is input to PFC(4, Power Factor Correction) and makes the PFC circuit works and the output voltage(+390Vdc) by PFC circuit becomes a Main Input voltage of MAIN(5), STANBY(10) Switching part.
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION IC802 0IMCRSG003A L4973D5.1 SGS-THOMSON 20P SOP TRANSISTOR 0IMCRRS001A IC001 R8820LV RDC SEMICONDUCTOR LTD IC002 0IDS232000A DS232AS 16P,SOP TP RS-232 DRIV FET,SI4925DY TP TEMIC 30V 6.1A SO IC709 0TF492509AA IC003 0IDS170800A...
Page 19
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.
Page 20
For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible LOCA.