Infinity Kappa Series 3-Way Component System 1.1cs Instructions page 3

Bi-Amp
RIGHT
+
–
Amplifier
GRN/WHT
(Tweeter & Mids)
GRN/BLK
–
GRN
+
+ –
LEFT
RED
Connect Pigtail
+ –
Jumpers As Shown BLK
RIGHT
+ – + –
WOOFER MIDRANGE TWEETER
+
AMPLIFIERS LEFT FROM
–
Amplifier
BLU/BLK
(Woofers)
–
–
+
To LEFT
LEFT
REFERENCE STANDARD AUTOMOTIVE
Woofer
+
Component System Crossover Network
HI
BLU
TO LEFT TO LEFT
MIDRANGE TWEETER
+
– LO HI – LO
GRY/ RED/
BLK BLK
GRY RED
– +
HI
To LEFT
4" Midrange
– +
Tri-Amp
To LEFT
Tweeter
RIGHT
+
–
Amplifier
GRN/WHT
(Tweeters) GRN/BLK
–
GRN
+
LEFT
+
Remove Pigtail + –
WOOFER MIDRANGE
RIGHT
AMPLIFIERS
+
–
Amplifier
BLU/BLK
–
(Midrange)
–
To LEFT
+
Woofer REFERENCE STANDARD AUTOMOTIVE
LEFT
+
HI Component System Crossover Network
BLU
TO LEFT
MIDRANGE
+
– LO HI
GRY/
BLK
RIGHT
GRY
+
– – +
Amplifier HI
To LEFT
(Woofers)
– 4" Midrange
+
LEFT
To LEFT
Tweeter
GRN
To Woofer Amplifier
RIGHT
– +
RED
– +
BLK
+ – – + – + – +
EMIT TWEETER EMIT MIDRANGE WOOFER
AMPLIFIERS RIGHT FROM
BLU/WHT
–
To RIGHT
Woofer
+
HI
BLU
TO RIGHT TO RIGHT
TWEETER MIDRANGE
+ + +
MID HI HI MID LO – HI LO –
RED/ GRY/
WHT WHT
RED GRY
+ –
HI
Figure 2. This application shows
To RIGHT
4" Midrange
connections for a Kappa1cs sys-
+ –
MID MID tem and two stereo amplifiers.
To RIGHT
Tweeter
GRN
To Midrange Amplifier
RIGHT
To Woofer Amplifier
RIGHT
– – +
+ – + – – + – + – +
TWEETER EMIT TWEETER EMIT MIDRANGE WOOFER
LEFT FROM AMPLIFIERS RIGHT FROM
BLU/WHT
–
To RIGHT
Woofer
+
HI
BLU
TO LEFT TO RIGHT TO RIGHT
TWEETER TWEETER MIDRANGE
+ + +
– LO MID HI HI MID LO – HI LO –
RED/ RED/ GRY/
BLK WHT WHT
RED RED GRY
+ –
HI
To RIGHT
4" Midrange
Figure 3. This application shows
– + + –
MID MID
connections for a Kappa1cs sys-
To RIGHT
Tweeter tem and three stereo amplifiers.
M I
IDRANGE NSTALLATION
sacle = 70%
Figure 5. Installing a Kappa 1.1cs/653.1cs midrange driver
in a door panel.
W I
OOFER NSTALLATION
Figure 4. Installing a Kappa1.1cs/653.1cs woofer
above a deck or (with the enclosed spacer) below
a deck.
NOTE: Use the mounting clips as nuts to secure
the below-deck installation.
T I
WEETER NSTALLATION
Figure 6. After installing the surface-mount plate, slide the
Kappa1.1cs EMIT-N™ tweeter down on the plate to lock in
place.
Figure 7. After sliding down the flush-mount clip onto the
back of the Kappa1.1cs EMIT-N tweeter, use the supplied
hardware to fasten the cup to the panel.
- 3 -