Sony CDX-V2800 Installation

2-661-354-12 (1)
FM/AM
Multi Media Player
Installation/Connections
CDX-V2800
© 2006 Sony Corporation
Printed in Thailand
  
  
× 4
 
Equipment used in illustrations (not supplied)
Front speaker Power amplifi er
Rear speaker Mobile colour TV
Active subwoofer
A
B
AUDIO
VIDEO OUT
OUT REAR
Cautions Connection example
• This unit is designed for negative earth 12 V DC
Notes (-B)
operation only. • Be sure to connect the earth lead before connecting the
amplifi er.
• Do not get the leads under a screw, or caught in moving
• If you connect an optional power amplifi er and do not use the
parts (e.g. seat railing).
built-in amplifi er, the beep sound will be deactivated.
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
Connection diagram
after all other leads have been connected.
• Run all earth leads to a common earth point.
• Be sure to in su late any loose un con nect ed leads with  To a metal surface of the car
electrical tape for safety.
First connect the black earth lead, then connect the yellow
and red power input leads.
Notes on the power supply lead (yellow)
 To the parking brake switch cord
• When connecting this unit in combination with other
Be sure to connect the parking cord (light green) to the
stereo components, the connected car circuit's rating
parking brake switch cord. The mounting position of the
must be higher than the sum of each component's fuse.
parking brake switch cord depends on your car. Refer to
"Connecting the parking cord" on the reverse side and
• When no car circuits are rated high enough, connect
consult your car dealer or your nearest Sony dealer for
the unit directly to the battery.
further details.
 To the power aerial control lead or power
supply lead of aerial booster amplifi er
Parts Iist
Notes
• It is not necessary to connect this lead if there is no power
× 2 aerial or aerial booster, or with a manually-operated
• The numbers in the list are keyed to those in the
telescopic aerial.
instructions.
• When your car has a built-in FM/AM aerial in the rear/side
• The bracket  and the protection collar  are
glass, see "Notes on the control and power supply leads."
attached to the unit before shipping. Before mounting  To AMP REMOTE IN of an optional power
the unit, use the release keys  to remove the bracket
amplifi er
 and the protection collar  from the unit. For
This connection is only for amplifi ers. Connecting any other
details, see "Removing the protection collar and the
system may damage the unit.
 To the +12 V power terminal which is
bracket ()" on the reverse side of the sheet.
• Keep the release keys  for future use as they
energized in the accessory position of the
are also necessary if you remove the unit from ignition key switch
your car.
Notes
• If there is no accessory position, connect to the +12 V
Caution
power (battery) terminal which is energized at all times.
Handle the bracket  carefully to avoid injuring your
Be sure to connect the black earth lead to a metal surface
fi ngers. of the car fi rst.
• When your car has a built-in FM/AM aerial in the rear/side
glass, see "Notes on the control and power supply leads."
 To the +12 V power terminal which is
energized at all times
Be sure to connect the black earth lead to a metal surface
of the car fi rst.

Catch
Note
Before installing, make sure that the catches on both sides of
the bracket  are bent inwards 2 mm. If the catches are straight
or bent outwards, the unit will not be installed securely and may
spring out.
* 1
VIDEO OUT AUX IN
*
AUX IN 4
L
R
from car aerial
AUDIO OUT
Fuse (10 A)
* 5
REAR
Blue/white striped
 AMP REM
Max. supply current 0.3 A
White
Left
White/black striped
Grey
Right
Grey/black striped
Green
Left
Green/black striped
Purple
Right
Purple/black striped
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V DC when
you turn on the tuner.
• When your car has built-in FM/AM aerial in the rear/side glass,
connect the power aerial control lead (blue) or the accessory
power input lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit's speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, "FAILURE"
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
* 1
* 1 RCA pin cord (not supplied)
* Supplied with the auxiliary equipment
2
* 3 Auxiliary optional equipment such as
* 3 portable DVD player (not supplied)
* 4 Be sure to match the colour-coded
cord for audio to the appropriate jacks
* 2
from the unit.
* 5 AUDIO OUT can be switched SUB or
REAR. For details, see the Operating
Instructions.
* 4 * 6 For details on connecting to the
parking brake switch cord, and
attaching the tap 8, see "Connecting
the parking cord" on the reverse side.

Black

*
6
Light green

Blue

ANT REM
Max. supply current 0.1 A
Red

Yellow
