Ozito OZSNG16A Instruction Manual

Ozito OZSNG16A Instruction Manual

8mm-14mm staple nail gun
Hide thumbs Also See for OZSNG16A:

Advertisement

STAPLE
NAIL GUN
8MM-14MM
INSTRUCTION MANUAL
SPECIFICATIONS
Input:
230V ~ 50Hz
Impact Rate:
20/min
Magazine Capacity:
100Pcs
Staple Type:
T50 18 Gauge
Staple Length:
8-14mm
Nail Type:
Brad 18 Gauge
Nail Length:
14-16mm
Weight:
0.95kg
ozito.com.au
WHAT'S IN THE BOX
Staple Nail Gun
Staples
Nails
OZSNG16A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OZSNG16A and is the answer not in the manual?

Questions and answers

Prisco
February 24, 2025

The ozsng16a staple/nil gun has a cassette where I can load staples, but I can't see where I would load nails. Have I got the wrong tool

User image 67bbfe53b27a6
1 comments:
Mr. Anderson
February 24, 2025

Yes, the Ozito OZSNG16A staple/nail gun has a loading mechanism for nails. To load nails, hold the tool upside down, squeeze the magazine latch, pull the magazine out, insert a row of nails into the opening behind the nose piece, align them to the marked side, and push the loaded magazine back into the unit until it clips into place.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Ozito OZSNG16A

  • Page 1 NAIL GUN Staple Nail Gun 8MM-14MM INSTRUCTION MANUAL Staples SPECIFICATIONS Input: 230V ~ 50Hz Impact Rate: 20/min Magazine Capacity: 100Pcs Staple Type: T50 18 Gauge Staple Length: 8-14mm Nail Type: Brad 18 Gauge Nail Length: 14-16mm Nails Weight: 0.95kg ozito.com.au OZSNG16A...
  • Page 2: Know Your Product

    KNOW YOUR PRODUCT SETUP & PREPARATION STAPLE NAIL GUN 1. LOADING STAPLES 1 Safety Striker Pin 5 Handle 2 Nosepiece 6 Power Switch NOTE: THIS STAPLER ONLY ACCEPTS T50 3 Magazine Window 7 Magazine Latch 18 GAUGE STAPLES. OTHER TYPES OF STAPLES, INCLUDING PAPER STAPLES, WILL JAM THE UNIT.
  • Page 3: Operation

    OPERATION 2. LOADING NAILS 3. CONTROLS 1. Hold the tool upside down. The tool is recommended for use with a residual current device with a rated residual current of 30mA or less. 1. To supply the tool with power, push the power switch to the “I”...
  • Page 4: Troubleshooting

    OCCURS THE UNIT WILL BE INOPERABLE. staple/nail. 4. With the magazine still open, tap the safety striker pin against a surface to disloge any loose NOTE: The on/off trigger cannot be squeezed unless the safety staples. striker pin is fully depressed. OZSNG16A...
  • Page 5: Maintenance

    Wall Decorations, Crafts, Covering Cornices, (8mm) Webbing, Light Fabrics. Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the staple nail gun by an unauthorised person or by Insulation, Carpeting, Wire Mesh, Plastic mishandling of the staple nail gun.
  • Page 6: Spare Parts

    Model No. OZSNG16A How To Order Available spare parts can be ordered through the Special Orders Desk at any Bunnings Warehouse. If you have any further questions, please contact Ozito Customer Service on: Australia: 1800 069 486 New Zealand: 0508 069 486...
  • Page 7: Electrical Safety

    Replace the extension lead if damaged or defective. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock.
  • Page 8: Warranty

    • Failure to perform maintenance as set out within the instruction manual. • If the tool is disassembled or tampered with in any way. • Professional, industrial or high frequency use. OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175. 0613...

Table of Contents

Save PDF