Network Easy Setting - Panasonic SC-BTT755 Operating Instructions Manual

SCBTT755_350EBGN_VQT2W23.book 22 ページ ２０１０年６月１８日 金曜日 午後４時５８分

Network Easy Setting

Select "Wired" or "Wireless" and press [OK].
Network Easy Setting (Connection Test)
Select a connection mode.
Current setting
LAN cable connection:
Connect a LAN cable to the unit and select "Wired".
Wireless LAN connection:
Connect the Wireless LAN Adaptor (DY-WL10) to the USB
port and select "Wireless".
OK
RETURN
∫ "Wired" connection
Follow the on-screen instructions to make your connection settings.
≥ When you experience problems (
∫ "Wireless" connection
If you select "Wireless" and "Wireless LAN Adaptor is not
connected." is displayed, check that the Wireless LAN Adaptor
is fully inserted. Alternatively, disconnect and reconnect it. If
there is still no change in the display, consult your dealer for
advice.
Select "WPS (PUSH button)" or "Search for
access point" and then follow the on-screen
instructions and make the settings.
Access Point Connection Setting
Select a connection method for access to
Wireless LAN.
Please refer to the operating instructions of
the access point about connection methods.
WPS (PUSH button):
If your Wireless router (Access point)
supports WPS (PUSH button), you can
easily perform the settings by pressing
WPS button on it.
WPS (Wi-Fi Protected Setup) is a
standard that facilitates settings relating
to the connection and security of
wireless LAN devices.
1 Press WPS button or corresponding button of Wireless
router (Access point) until the lamp starts flashing.
≥ For details, refer to the operating instruction of Wireless
router (Access point).
2 Press [OK].
*1 Wi-Fi Protected Setup-compatible Wireless router (Access point) may
have the mark.
Search for access point:
Available Wireless routers (Access points) are searched and
listed. You can select the one to use from the list.
1 Press [3, 4] to select SSID*
point) you want to connect with. Then press [OPTION] to
show information of the selected router, make a note of the
authentication and encryption type.
Access Point Connection Setting
Select an access point to connect with.
To search for access point again, please
select "Search again" below.
SSID
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
SSID
XXXXXXXXXX
Wireless type
XXXXXXXXXX
Authentication type
XXXXXXXXXX
XXXXXXXXXX Encryption type
XXXXXXXXXX
VQT2W23
22
≥ If you can not find the SSID*
: Wired
Wired
Wireless
right)
WPS (PUSH button)
Search for access point
e.g.,
of Wireless router (Access
2
Reception
:XXXXXXXXXXXXXXX
:802.11n/g/b (2.4GHz)
:WPA-PSK
:AES
Search again
OK
, select "Search again".
2
2 Press [RETURN] and then press [OK].
Then select an item on the following screen which
corresponds to the authentication type noted down in step
1 ( left).
Access Point Connection Setting
Select authentication type.
Follow the on-screen instructions to make the settings.
≥ Input your encryption key code in "Encryption Key"
supplied with your Wireless router (Access point).
When you experience
problems with settings
Access Point Connection Setting
Access Point Connection Setting
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point
Connection Setting again ?
OK
Display
A conflict with other
devices occurred.
A time out error occurred.
1
An authentication error or a
time out error occurred.
A device error occurred.
WPA2-PSK (AES/TKIP)
WPA-PSK (AES/TKIP)
Open/Shared Key (WEP)
Open system
Yes No
Check the following
≥ Please wait a few moments,
and then try again.
≥ Setting of the Wireless
router (Access point) for
MAC Address etc.
≥ The signal may be weak.
Using the USB extension
cable supplied with the
Wireless LAN Adaptor,
adjust the position of the
Wireless LAN Adaptor.
≥ The SSID* and the
2
encryption key of the
Wireless router (Access
point).
≥ Please wait a few moments,
and then try again.
≥ Connection of Wireless LAN
Adaptor
If there is no improvement in
symptom, consult your
dealer.