Table of Contents
Advertisement
Quick Links
VMD1
(6901-002123 <01>)
I N S T A L L A T I O N I N S T R U C T I O N S
Sanus
6436 City West Parkway
Eden Prairie, MN 55344 USA
Customer Service
Americas: 800-359-5520 • 952-225-6013 • info@sanus.com
Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com
Asia Pacific: 86 755 8996 9226 • sanus.ap@milestone.com
www.sanus.com
Advertisement
Table of Contents
Related Manuals for Sanus VMD1
Summary of Contents for Sanus VMD1
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Sanus 6436 City West Parkway Eden Prairie, MN 55344 USA Customer Service Americas: 800-359-5520 • 952-225-6013 • info@sanus.com Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com Asia Pacific: 86 755 8996 9226 • sanus.ap@milestone.com www.sanus.com...
-
Page 2: Installation Instructions
Milestone AV Technologies, a Duchossois Group Company. component. The wall to which the mount is being attached All rights reserved. Sanus is a division of Milestone. may have a maximum drywall thickness of 5/8" (1.6cm). All other brand names or marks are used for identification purposes and are trademarks of their respective owners. - Page 3 VMD1 Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
-
Page 4: Tools Required For Installation
VMD1 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (included) 1/8" (included) PARTS A (1) [monitor arm] B (4) C (4) D (4) M4x14mm M4x25mm M10x5.3x10 E (1) F (1) 3/16" 1/8" (6901-002123 <01>) - Page 5 Installation Instructions VMD1 Connecting VMD1 to Desk Loosen clamp screw until enough space is created between clamp and mount to allow for desk mounting. (See Figure 1) NOTE: If space is limited behind desk (i.e. against wall, etc.), remove clamp entirely in Step 1 and reattach clamp prior to Step 3! Place mount on top of desk at desired mounting location.
-
Page 6: Display Installation
VMD1 Installation Instructions Display Installation For recessed mounting hole installation: • Place four spacers (D) on top of mounting holes Remove quick release faceplate from mount by pressing on back of display. (See Figure 9) quick release tab and sliding faceplate off mount. (See Figure 2) •... - Page 7 Installation Instructions VMD1 Adjustments edge of desk (top view) Head Tilt Adjustment Adjust head tilt to desired tilt position. (See Figure 6) Adjust head tilt tension screw to change the adjustment tension. (See Figure 6) Height Adjustment CAUTION: OVERTENSIONING THE HEIGHT-...
-
Page 8: Cable Management
VMD1 Installation Instructions Cable Management Route cables through cable management channels. (See Use screwdriver to unhinge tab on either end of cable Figure 10) management cover on upper arm. (See Figure 9) IMPORTANT! Be sure to leave enough slack in the...
Need help?
Do you have a question about the VMD1 and is the answer not in the manual?
Questions and answers