Program Menus - Wilbur Curtis Company CBS Service Manual

Your Curtis ADS System is Factory Pre-Set for Optimum Performance.
After connection to water and power; the rear toggle switch must be on. You will hear a beep sound, indicating power is available to the controller.
The control displays
CURTIS
Water will fi ll the tank (approximately 2-3 minutes depending on water fl ow rate). When the proper level is reached
screen. It takes approximately 20 minutes to reach setpoint temperature of 204°F.
Control will display
CURTIS
READY TO BREW
To Go Into Programming
Turn off (dark display) by pressing ON/OFF button (yellow). Press and hold BREW button 4 (green) and then press and release ON/OFF button (yellow).
Continue holding BREW button. Display will read
spond to the buttons (see illustration below).
The default code set at the factory is 1-2-3-4. Then
1 2

PROGRAM MENUS

Program Menus
Tea Recipes
Tea By Volume
Tea By Time
Tea Dilut. Delay
Tea Dilut. Volume
Tea Dilut. Time
. Press ON/OFF button and the screen will display
when temperature reaches the setpoint (204°F). Unit is now ready to brew.
ENTERING PROGRAM
MODE
PROGRAM MENUS
< SELECT >
3 4
Brew Volume (Factory set to 3.0 Gallons)
Selecting Brew by Volume or Brew by Time depends on whether you know your brew time before starting.
From Program Menus press > display will now show the next feature.
Tea Recipe (Factory set to Standard Tea)
Press  to Select. Press < or > to toggle between STANDARD TEA, TROPICAL TEA and RECIPE #3 76/308. Set
and exit by pressing .
Tea by Volume: Scroll until Brew by Volume is displayed. Press  to Select. The display will read Select Brew
Button! Button! Once the desired brew button is selected, the display will read Button! Once the desired brew button is selected, the display will read
BREW button and hot water starts dispensing. When the desired volume is reached, press BREW BREW button and hot water starts dispensing. When the desired volume is reached, press
the fl ow. The brew volume has now been set. When EXIT is displayed, Press
ming mode. Pressing > button will display the subsequent menu features.
Tea by Time. Press  to Select. Press < or > to toggle between STANDARD TEA (4 min, 12 sec), TROPICAL
TEA (3 min, 30 sec) and RECIPE #3 76/308 (4 min). Set and exit by pressing . Tea by Time has a range of 0:00
to 9:59 (Increments are minutes and seconds).
Dilution Delay Press  to Select. Press < or > to toggle between STANDARD TEA (30 sec), TROPICAL TEA (9 Dilution Delay: Dilution Delay:
min) and RECIPE #3 76/308 (4 min). Range is from 0 seconds, 1 minute to 10 minutes.
Dilution Volume: Press  to Select, Display will now show Push START To Begin... Press the BREW button then
water starts running, when desired volume is reached press BREW button again to stop the fl ow. Now the volume
has been set. Pressing > button will display the subsequent menu features.
Dilution Time: Press  to Select. Press < or > to toggle between STANDARD TEA (4 min, 05 sec), TROPICAL
TEA (4 min, 26 sec) and RECIPE #3 76/308 (4 min 55 sec). Dilution Time is from 30 sec to 9 min, 59 sec.
<Coffee/TeaBrewer>
CURTIS
hold hold BREW button 4 (green) and then press and release ON/OFF button (yellow).
, wait until is displayed Enter the 4-digit access code, the digits 1-4 corre-
ENTER CODE
– – – –
will be displayed.
All programming selections are performed with the three center buttons.
The symbols below the buttons are:
Scroll LEFT
 SELECTION or ENTER to save new parameter
Scroll RIGHT Scroll RIGHT
EXIT EXIT is displayed, Press
. After three seconds,
CURTIS
FILLING
CURTIS
HEATING HEATING
Press BREW to Start 0:00 Time. Press the
BREW BREW again to stop BREW again to stop
 to select and exit the program-
Continued on Page 4
is displayed.
will appear on the
3