Subscribe to Our Youtube Channel
Related Manuals for MyBinding Challenge Spartan 150M
Summary of Contents for MyBinding Challenge Spartan 150M
- Page 1 CHALLENGE SPARTAN 150M PAPER CUTTER Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 Serial Numbers 041001 & Up PERATOR’S ANUAL SPARTAN 150 M DIGITAL/LEVER PAPER CUTTER Sold and Serviced by The Challenge Machinery Company 6125 Norton Center Drive Norton Shores, MI. 49441 www.challengemachinery.com F.150M-O Apr 2007...
-
Page 3: Introduction
1.0 Introduction 1.0 Introduction THIS MANUAL is designed to help you get the most from your Challenge equipment. Keep this manual in a safe, convenient place for quick reference by operators and service personnel. SAFETY ALERT! This symbol means CAUTION: Personal safety instructions! Pay special attention to the instructions in bold type. -
Page 4: Table Of Contents
1.0 Introduction TABLE OF CONTENTS 1.0 Introduction ............................2 2.0 Safety ..............................4 2.1 Precautions ...........................4 2.2 Power Lockout Procedure ......................4 2.3 Warning Label Definitions......................5 3.0 Packing List............................7 4.0 Specifications ............................8 5.0 Installation & Setup ...........................9 5.1 Inspecting Shipment ........................9 5.2 Uncrating ............................9 5.3 Cleaning............................9 5.4 Power Hook-Up ..........................9 5.5 Mounting to Optional Stand ......................9... -
Page 5: Safety
2.0 Safety 2.0 Safety 2.1 Precautions • This machine is designed for one-person operation. Never operate the machine with more than one person. • Safe use of this machine is the responsibility of the operator. Use good judgment and common sense when working with and around this machine. -
Page 6: Warning Label Definitions
2.0 Safety 2.3 Warning Label Definitions The following warning labels are found at various locations on your machine. Read and understand the meaning of each symbol. If a label is lost from the machine, it should be replaced. HAZARDOUS AREA Disconnect power before cleaning, servicing, or making adjustments not requiring power. - Page 7 2.0 Safety !OJO! This Este simbolo de alerta de seguridad significa ¡ OJO ! - INSTRUCCIONES DE SEGURIDADPERSONAL. Lea las instrucciones porque se refieren a su seguridad personal. Fall de obedecer las instrucciones que siguen podria resultar en lesiones corporales. •...
-
Page 8: Packing List
3.0 Packing List 3.0 Packing List Part No. Description Qty. Spartan 150 M 15” Digital/Lever Paper Cutter 60011-2 Knife – Standard (installed in machine) 60057 Cutting Stick F.150M-O Operator Manual 60058 Jogging Aid 60061 Knife Lifter Assembly 61036 Lever Handle 5064 Cut Stick Puller W-189... -
Page 9: Specifications
4.0 Specifications 4.0 Specifications Description Inch Units Metric Units Cutting Width 15-3/4” 40 cm Minimum Cut 1-15/16” 4.9 cm Clamp Opening 1-1/2” 3.8 cm Table Space Front: 6-1/4” 15.9 cm Back: 15-1/4” 38.7 cm Dimensions Overall Height 12-1/2” 31.8 cm Overall Height with Optional 45-1/4”... -
Page 10: Installation & Setup
5.0 Installation & Setup 5.0 Installation & Setup 5.1 Inspecting Shipment This machine has been carefully packed to prevent damage during shipment. However, claims for damage or loss are the responsibility of the recipient. Inspect all shipments as soon as they are received. -
Page 11: Operation
6.0 Operation 6.0 Operation IMPORTANT: DO NOT ATTEMPT TO OPERATE THE CUTTER UNTIL YOU HAVE THOROUGHLY READ AND UNDERSTAND ALL OF THE FOLLOWING INSTRUCTIONS. CALL YOUR AUTHORIZED CHALLENGE DEALER IF YOU STILL HAVE ANY QUESTIONS. Cutting Lever Handle Cutting Lever Clamp Handle Knife Latch Lever... -
Page 12: Backgauge Control
6.0 Operation 6.2 Backgauge Control The backgauge is used to position paper to the desired location when cutting. The backgauge is operated by the hand crank at the front of the machine. The backgauge position is shown by a lighted LED display. When the machine is first powered up, the display shows four lines as follows, indicating the display needs to be reset. -
Page 13: Jogging Aid
6.0 Operation 6.3 Jogging Aid Always remove the jogging aid from the table before making a cut. A jogging aid is included as standard equipment with the Spartan 150. This tool allows the operator to load and align paper without the need to place hands or arms under the knife or clamp. To use, load the paper against the side and backgauge using the jogging aid (Figure 7 &... -
Page 14: Line Light
6.0 Operation 6.4 Line Light The Spartan 150 comes standard with an LED line light. The line light switches on and stays on whenever the power is on. To use, simply align paper under clamp, and use the red light line as an indicator of where the cut will be made (Figure 9). -
Page 15: Adjusting The Knife Depth
6.0 Operation 6.6 Adjusting the Knife Depth The depth of cut can be adjusted using the knife depth adjusting screw located on the left side of the machine. The same T-handled wrench used for changing the knife can be used to adjust the screw. Turn the screw counter-clockwise to increase knife depth, and clockwise to decrease knife depth. -
Page 16: Knife Installation/Changing
7.0 Knife Installation/Changing 7.0 Knife Installation/Changing Changing knives can be very dangerous unless safety precautions are observed and extreme care is taken when handling knives. • Make sure knife lifters are used properly, see instructions following. • Keep handling of unprotected knives to an absolute minimum. •... -
Page 17: Knife Installation
7.0 Knife Installation/Changing 3. With the knife at its extreme up position, lift the hood. 4. Remove the two knife bolts that are mounted in open slots in the knife bar. 5. Install the knife lifter onto the knife holder. Screw the handles into the holes from which the two, knife bolts were removed. -
Page 18: Knife Care Tips
7.0 Knife Installation/Changing entire width of paper is cut completely through. Do not allow the knife to cut too deep into the cut stick. Cutting excessively deep into the stick will reduce its life. 10. Send dull knives to a knife grinder – do not attempt to sharpen your own knives! Knives that do not have a minimum height of 1-1/2”... -
Page 19: Bevel Angle
7.0 Knife Installation/Changing 7.3.3 Bevel Angle Challenge recommends that the bevel angle for the Spartan 150 knives be 20° . Order a re- sharpened knife to the following specification, “20 , DEAD SHARP, NO MICRO-BEVEL.” A micro- bevel on this knife will cause strenuous cutting. If an operator requires cutting with less physical strain, knives may be re-sharpened to 18 . -
Page 20: Footprint
8.0 Footprint 8.0 Footprint... -
Page 21: Safety Systems Test
9.0 Safety Systems Test 9.0 Safety Systems Test Machine manufacturer CHALLENGE Model SPARTAN 150 M Serial Number __________________ Frequency of test: THESE TESTS SHOULD BE PERFORMED WEEKLY. Test #1: Move the cutting lever to its right-most position. Move the knife latch to the right and the cutting lever slightly to the left. - Page 22 9.0 Safety Systems Test Please enter date and initials for both tests. Date ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ Test 1 ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ Test 2 ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ Date ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ Test 1 ______ ______ ______ ______ ______ ______ ______ ______ ______ ______ ______...
Need help?
Do you have a question about the Challenge Spartan 150M and is the answer not in the manual?
Questions and answers