Table of Contents
Advertisement
Quick Links
36" & 48" VENTILATION HOOD
INSTRUCTION & INSTALLATION MANUAL
Contact Information:
Customer Service:
Business (519) 650-5775
Fax (519)650-3773
Toll Free Telephone 1-877-650-5775
Toll Free Fax 1-800-327-5609
C
Please read entire instructions before proceeding.
Installation must comply with all local codes.
IMPORTANT: Save these instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
SAFETY WARNING: Before servicing or cleaning the unit, switch the power
off at the service panel and lock out the service disconnect switch to prevent
power from being switched on accidentally. When the service disconnect
switch cannot be locked, securely fasten a prominent warning device, such
as a tag to the service panel.
Record the model and serial numbers before installing the Aga ventilation
hood. Both numbers are listed on the rating plate, located on the left wall of
the hood shell.
Model Number_______________________________
Serial Number_______________________________
070208
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AGA VENTILATION HOOD
Summary of Contents for AGA VENTILATION HOOD
- Page 1 Record the model and serial numbers before installing the Aga ventilation hood. Both numbers are listed on the rating plate, located on the left wall of the hood shell.
-
Page 2: Important Safety Instructions
Important Safety Instructions To Reduce the risk of injury, please observe the instructions provided Prevent Injury to Persons in the Event For general ventilating use: observe of a Range Top Grease Fire. the following. 1. Local building codes may require the use of make-up 1. -
Page 3: Table Of Contents
Installation Planning Overall Dimensions Installation Methods Method 1: Ventilation Hood - Ceiling Mounted Method 2: Ventilation Hood - Wall Mounted Method 3: Ventilation Hood - Rough-In Plate Mounted Installation Assembly Rough-in Plate Mount Installation Mounting the In-Hood Fan Ducting Connection... -
Page 4: Installation Precautions
Installation Precautions The high degree of craftsmanship in the construction and Cotton gloves are preferable. They will protect the surface finish of your hood requires careful handling to ensure from fine scratches and eliminate finger prints. proper installation. Remove all rings, watches, belt buckles, and jackets Do not remove your hood from its carton until you are (snaps-zippers) to prevent scratch marks. -
Page 5: Installation Planning
48” Models 48” Models How to Steps How to Steps Aga Vent Hood Clearances: Optional Accessories - Duct Covers: • Vent Hood to either side of cabinetry: 0” • Duct Cover - depth: 12” Cooktop to underside vent hood: 30”-36” max (76-92cm) standard heights:12”,18”,or 24”... -
Page 6: Overall Dimensions
Overall Dimensions Dimensions 12” UPPER REVEAL DEPTH 5” 18” HEIGHT 36” 48” WIDTH 2-1/2” ELECTRICAL INLET CENTER 24” LINE 20-3/4” FRONT BACK INSTALLING HOOD AT TOP INSTALLING HOOD FROM REAR 8” Transition for 36” Models 8” Round Duct for 36” Models 10”... -
Page 7: Installation Methods
(allthreads, nuts, etc.). Be sure the location will not interfere with wiring, other utilities, or structural considerations. Method 1: Ventilation Hood - Ceiling Mounted 1. Use 2x4s, Unistrut or Angle Iron, to construct the framing. The considerable weight of the hood makes this necessary. -
Page 8: Method 2: Ventilation Hood - Wall Mounted
Position screws such that damper assembly can open and close. 10. Make electrical connections.(An electrical contractor should make all electrical connections. See wiring diagram.) Method 3: Ventilation Hood - Rough-In Plate Mounted 8” or 10” round duct Transition rough-in plate... -
Page 9: Installation Assembly
Installation Assembly Rough-in Plate Mount Installation WARNING CAUTION Framing must be tied together and to ceiling joists to provide enough If wall framing is not available, wall structural strength to support the anchors must be used. weight of the hood and internal blower, if applicable The hood unit is shipped with the rough-in plate and Shipping Screws... -
Page 10: Mounting The In-Hood Fan
Fig. 2 Fig. 1 Mounting the In-Hood Fan Install the fan by aligning the holes on the fan to the weld studs on the rough-in plate. Tighten the fan to Fan Plate the plate using the nuts provided. Keyhole Plug the “Molex” plug on the fan to the “Molex” plug on the hood. -
Page 11: Electrical Connection
Electrical Connection Run power cable to installation location. Remove wiring cover, Power Supply install wire clamp, insert cable in hood through wire clamp and To Remote Fan (if used) secure by tightening the wire clamp. Connect cable into wiring box, located on rough-in plate, using wire nuts. -
Page 12: Installation Of Grease Troughs, Filters,Lamps
Installation of Grease Troughs, Filters,Lamps Grease trough location is on the underside (bottom), rear area of the hood. In the center of the space provided for the filters, insert one Hood filter on the top ledge and pull back until the bottom of the Assembly filter slips into bottom ledge. -
Page 14: Ventilation Hood Customer Warranty
2. Warranty applies to product only in the country in which it was purchased. 3. AGA-Heartland is not liable for any claims or damages resulting from any failure of the range hood or from service delays beyond their reasonable control.
Need help?
Do you have a question about the VENTILATION HOOD and is the answer not in the manual?
Questions and answers