Cisco SPA232D Quick Start Manual
Mobility enhanced ata
Hide thumbs
Also See for SPA232D:
- Provisioning manual (213 pages) ,
- User manual (10 pages) ,
- Administration manual (236 pages)
Related Manuals for Cisco SPA232D
Summary of Contents for Cisco SPA232D
-
Page 1: Quick Start Guide
Quick Start Guide Cisco SPA232D Mobility Enhanced ATA Package Contents • Analog Telephone Adapter • Ethernet Cable • Phone Cable • Power Adapter • Quick Start Guide • Product CD-ROM... -
Page 2: Before You Begin
Enhanced Cordless Handset with the Cisco SPA232D, which has an integrated DECT Base Station. Cisco SPA302D handsets registered to the Cisco SPA232D can make and receive calls through a Voice over IP (VoIP) service provider and through the local telephone system (via the LINE port). -
Page 3: Product Features
Restart the ATA: Press quickly (less than a second) with a paperclip or similar object. Restore the factory default settings: Press and hold for 10 seconds. LINE (Green) Connects to an analog phone line, using an RJ-11 phone cable. Cisco SPA232D Quick Start Guide... - Page 4 (Also the address for the web- based configuration utility.) DHCP Range 192. 1 68. 1 5. 1 00-149 (DHCP server enabled by default.) Netmask 255.255.255.0 PIN for handset registration, IP Blank settings, and SIP settings Cisco SPA232D Quick Start Guide...
-
Page 5: Connecting The Equipment
Connect an analog phone line to the LINE (Green) port to connect the ATA to your local telephone system. Connect the provided power adapter to the POWER port. The unit powers on. Cisco SPA232D Quick Start Guide... -
Page 6: Configuration And Management Of The Ata
The password is case sensitive. NOTE: A user account allows access to limited settings and status pages. To log in as a user, enter cisco as the username and the password. Use the Quick Setup page as needed to register your VoIP accounts in the fields for Line 1 and DECT Line1. -
Page 7: Registering A Cisco Spa302D Handset
Note: The Cisco SPA232D assigns DECT Line1 as the default line for outgoing calls from Cisco SPA302D handsets. If needed, you can configure additional VoIP accounts as separate “DECT Lines.” To do so, choose the Voice menu, and then use the DECT Line 1~10 links in the navigation tree. -
Page 8: Additional Information
**** will need to re-enter the menu by pressing the star key four times: Your settings take effect after you hang up the telephone or exit the IVR. The ATA may reboot at this time. Cisco SPA232D Quick Start Guide... - Page 9 Press the * (star) key to enter a decimal point. Note: This option is available only after you choose Static IP as the Internet Connection Type, through option 101. Cisco SPA232D Quick Start Guide...
- Page 10 1910 Transport Set Line 1 SIP Transport 1911 0: UDP 1: TCP 2: TLS Check Line 2 SIP Transport 1920 Set Line 2 SIP Transport 1921 0: UDP 1: TCP 2: TLS Exit IVR 3948 Cisco SPA232D Quick Start Guide...
- Page 11 This successful,” hang up the includes network and phone. The ATA reboots. service provider data. Reboot of Voice System 732668 After you hear “Option successful,” hang up the “REBOOT” phone. The ATA reboots. Cisco SPA232D Quick Start Guide...
-
Page 12: Mounting The Ata
Recommended hardware (not included): Two number-six pan-head tapping screws, 5/8-in. length, with anchors for sheet rock installation. 15,8 mm Insecure mounting might damage the ATA or cause injury. Cisco ARNING is not responsible for damages incurred by insecure wall- mounting. - Page 13 Place the unit wall-mount slots over the screws and slide the unit down until the screws fit snugly into the wall-mount slots. Cisco SPA232D Quick Start Guide...
-
Page 14: Where To Go From Here
Cisco Small Business www.cisco.com/go/smallbiz_opensource_ Open Source Requests request Product Documentation Cisco Small Business www.cisco.com/go/smallbizvoicegateways Analog Telephone Adapters Cisco Small Business Cisco Partner Central www.cisco.com/web/partners/sell/smb for Small Business (Partner Login Required) Cisco Small Business www.cisco.com/smb Home Cisco SPA232D Quick Start Guide... - Page 16 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners.