Table of Contents
Advertisement
Vorderer Weinberg 26
• D-71522 Backnang •
Models:
Available powers (kVA / kW)
Generals
Cold start
Green mode
IEC inlet connectors
IEC outlet connectors
Communication ports
Dry contacts
Protection connectors for Modem / ADSL
/ Fax
Installation connector for external EPO
Slot for COM option cards
Option cards (to insert into the slot)
Monitoring software
Ruido acústico a 1 m en modo línea
Acoustic noise at 1 m on battery mode
Operating temperature
Storage temperature
Storage temperature with no batteries
Operating altitude
Relative humidity
Protection degree
UPS dimensions -Depth x Width x Height-
(mm)
Bat. dimensions -Depth x Width x Height- (mm)
UPS weight (kg)
Battery modules weight (kg)
Safety
Electromagnetic compatibility (EMC)
Marking
Quality system
Tabla 13. General technical specifications.
8.2.
Glossary.
AC.- It is nominated as alternating current (abbrevia-
tion in Spanish CA and in English AC) to the electrical
current in which the magnitude and direction varies
in a cyclic way. The most common wave shape of the
alternating current is sinewave, because the energy
transmission is better. Nevertheless, some applications
could need other period wave shapes, like triangular or
square.
Bypass.- Manual or automatic, it is the physical junction be-
tween the input and the output electric device.
DC.- The direct current (CC in Spanish, DC in English) is the
continuous electron flow through a cable between two points
with different potential. Unlike the alternating current, in direct
current the electrical loads always flow in the same direction
from the highest potential point to the lowest one. Although,
usually the direct current is identified with the constant cur-
rent (for example the one supplied by the battery), it is con-
tinuous any current that always maintain the polarity.
DSP.- It is the acronym of Digital Signal Processor. A DSP is
a system based on a processor or microprocessor that has
instructions in it, a hardware and an optimised software to
develop applications where numerical operations are needed
with very fast speed. Due to this, it is very useful to process
analogical signals in real time: in a system that runs in this
way (real time) samples are received, usually coming from an
analogical/digital converter(ADC).
Power factor.- It is defined as power factor, p.f., of an alter-
nating current circuit, as the ratio between the active power,
SALICRU
Tel.:+49 (0)7191 3560-0 (Fax.:-19)
0.750 / 0.675
1 / 0.9
1.5 / 1.35
10 A
4 x IEC 10A
2 (RS232 -DB9- and USB, mutually exclusive)
Yes, through optocouplers (low battery and mains fault). Included in the same connector as the RS232 port.
No
No
No
< 40 dB
< 45 dB
436 x 438 x 86.5 (2U)
-
436 x 438 x 86.5 (2U)
13
14
18.5
-
20.5
SPS.ADV RT
1.5 / 1.35 (B1)
2 / 1.8
2 / 1.8 (B1)
Yes
Yes (selectable)
8 x IEC 10A (4 x LS1 + 4 x LS2) + 1 IEC 16 A (3kVA UPS only)
1 input / 1 output
Yes
Yes
AS400, SNMP, remote management internet or intranet
WinPower (free download)
0.. +40 ºC
–15.. +50 ºC
–20.. +70 ºC
1501 - 3000 m (0.. +35 ºC)
0-95 % non-condensing
IP20
608 x 438 x 86.5 (2U)
608 x 438 x 86.5 (2U)
12.5
28
15
EN-IEC 62040-1; EN-IEC 60950-1
EN-IEC 62040-2
CE
ISO 9001 and ISO 140001
P, and the apparent power, S, or as the cosines of the angle
that make the current and voltage vectors, designating as
GND.- The term ground, as its name states, refers to the po-
tential of the earth surface.
EMI filter.- Filter able to decrease the electromagnetic inter-
ferences, which is the perturbation that happens in a radio
receptor or in any other electrical circuit caused by the elec-
tromagnetic radiation coming from an external source. Also
it is known as EMI, ElectroMagnetic Interference, Radio Fre-
quency Interference or RFI. This perturbation can derate or
limit the efficiency of the circuit.
IGBT.- The Insulated Gate Bipolar Transistor is a semicon-
ductor device that is used as a controlled switch in power
electronic circuits. This device has the feature of the gate
signal of the effect field transistors with the capacity of high
current and low voltage saturation of the bipolar transistor,
combining an isolated FET gate for the input and a bipolar
transistor as switch in a single device. The triggering circuit
of the IGBT is as the MOSFET one, while the driving features
are like the BJT.
Interface.- In electronic, telecommunications and hardware,
an interface (electronic) is the port (physical circuit) through
which are sent or received signals from a system or subsys-
tems toward others.
kVA.- The voltampere is the unit of the apparent power in
electrical current. In direct current is almost equal to the real
power but in alternating current can defer depending on the
power factor.
3 / 2.7
3 / 2.7 (B1)
16 A
< 45 dB
< 50 dB
29
17
33.5
31
Advertisement
Table of Contents
