Extron electronics RGB 190F User Manual page 12

Reference Information
Reference Information, cont'd
Specifications
Video
Gain ............................................... Unity (0.7V), (0.80V) 15% with 3dB
peaking
Bandwidth .................................... 300 MHz (-3dB)
Rise time ........................................ 1.5 ns
Video input
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB
Connectors .................................... (1) 15-pin HD female
Nominal level ............................... 0.7V p-p for RGB
Minimum/maximum levels ...... Analog: 0.3 to 1.45 volts p-p with no offset
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 170 Hz
Return loss .................................... -41dB @ 5 MHz
Maximum DC offset .................... 4V
Video output
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB
Connectors .................................... 6 BNC female
(1) 15-pin HD female (buffered local
monitor output)
Nominal level ............................... 0.7V p-p for RGB
Minimum/maximum levels ...... Analog: 0.7V to 0.8V p-p (DIP switch
selectable) w/peaking
Impedance .................................... 75 ohms
Return loss .................................... -45dB @ 5 MHz
DC offset ....................................... ±5mV maximum with input at 0 offset
Sync
Input type ..................................... RGBHV, RGBS, RGsB (accepts RGsB but
does not strip sync from video)
Output type .................................. RGBHV at all times
RGBS at all times
RGsB (switch-selectable)
Input level ..................................... 2V p-p to 5.5V p-p with ±0.2VDC offset
max.
Output level .................................. 4V to 5V p-p
Input impedance .......................... 510 ohms
A-2 RGB 190F, RGB 192 • Reference Information
at unity gain
Output impedance ...................... 75 ohms
Max. propagation delay .............. 57 ns
Max. rise/fall time ....................... 4 ns
Polarity .......................................... RGBHV ...................... when RGBHV is
RGBS, RGsB .............. negative
Audio — RGB 192 only
Gain ............................................... Unbalanced stereo or mono 0dB, balanced
+6dB
Frequency response ..................... 20 Hz to 20 kHz, ± 0.05dB
THD + Noise ................................ 0.03% @ 1 kHz, 0.3% @ 20 kHz at rated
maximum output drive
S/N ................................................ >90dB at rated maximum output (14dBm),
balanced
Crosstalk ....................................... <-90dB @ 1 kHz
Stereo channel separation .......... >90dB @ 1 kHz to 20 kHz
Audio input — RGB 192 only
Number/signal type ................... 1 stereo, unbalanced, or mono
Connectors .................................... (1) 3.5 mm stereo jack (2 channel),
unbalanced; tip (R), ring (L), sleeve
(ground)
Impedance .................................... >10 kohms, unbalanced, DC coupled
Maximum level ............................ +9.5dBu at stated %THD+N
Audio output — RGB 192 only
Number/signal type ................... 1 buffered, stereo (2 channel) or mono,
balanced or unbalanced
Connectors .................................... (1) 3.5 mm captive screw connector, 5
pole
Impedance .................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ...................................... ±0.1dB channel to channel
Maximum level (Hi-Z) ................ >+14dBm, balanced at stated %THD+N
Maximum level (600 ohm) ......... >+9dBm, balanced at 1% THD+N
General
Power ............................................. 100VAC to 240VAC, 50/60 Hz, 3.2 watts,
external, autoswitchable; to 12VDC, 1.0 A
power supply (included). Product
requires 0.35 A.
RGB 190F, RGB 192 • Reference Information
input, polarity
follows input;
otherwise negative
A-3