Electrical Connection - Westinghouse Cooker Instruction Booklet

TO FIX THE COOKER TO THE REAR WALL
WARNING - For safety reasons and to prevent tipping of the appliance,
these stabilizing means must be installed.
The cooker is equipped with 2 chains fixed on each side at the rear of
the cooker near the top (see Fig. A). The chains are fitted with “spring
clips” which must be clipped to the “screw eyes” provided with the cooker.
Install the “screw eyes” as follows :
1. Drill four 6mm holes (position 1 - 2 - 3 - 4) in the wall
as in Fig. A.
2. Insert part “R” into the holes then screw in the “screw eyes” part
“G” see Fig. B.
Note: If the part provided is not suitable for the wall material please
use an appropriate device to ensure secure holding of the “screw
eyes” to the wall.
3. Bring the cooker near the wall and clip the chains on the
“screw eyes” as in Fig. C.
IMPORTANT: If the cooker is moved for any reason
(e.g. maintenance) resulting in the cooker being unclipped from the
wall, the cooker must be re-clipped to the wall at the completion of
the task.
Fig. A
Fig. B
G R
The cooker is fitted with 4 legs for an eventual alignment in height
with the furniture (Fig. D) .
Fig. D
Fig. C
wall
G
OK NO

ELECTRICAL CONNECTION

This appliance must be earthed by law. Before connecting the
appliance to the electrical supply, check that the earth system in
your house is working correctly.
Check that unit voltage and power, marked on the rating plate applied on
the appliance, are correct for the supply. Ensure disconnection from the
supply is easily accessible by installation of an isolation switch, in
accordance with local wiring rules.
It is necessary that the feeding network is protected by a powerful switch
able to disconnect completely the network with a contacts separation of
at least 3 mm. Be sure that the earth wire green/yellow is not interrupted
by the switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
Connecting the mains cable
Open the mains terminal block cover as shown, unscrew the cable
clamp «A» and unscrew (not fully) the screws in the mains terminal
block which secure the three wires of the mains cable.
Fit the cable and refit the cable clamp «A» (fig. 1) .
IMPORTANT
The wires in the mains lead are coloured in accordance with the following
code:
GREEN & YELLOW .....................................................................EARTH
BLUE .......................................................................................NEUTRAL
BROWN ............................................................................................LIVE
The supply cable must not come into contact with any component the
temperature of which exceeds the ambient temperature by 50°C.
Easy access to the plug or the switch is ensured once the appliance is
installed.
Ensure that there is sufficient cable allowed for any subsequent removal
of the unit.
‘In order to avoid hazard, any electrical work performed on this equipment
or its associated wiring, should only be done by persons authorised by
the supplier or similarly qualified persons.’
Note: this product is supplied from the factory ready for single phase 230-
240V installation.
Some models with single-phase supply can be supplied from a three
phase source by performing the following.
Move the connection U bolts depending on the type of supply
(see table below).
*
TAKING ACCOUNT OF CONTEMPORANEITY FACTOR OF 0,62
Single phase Three phases
connection connection
230-240 V~ 400V 2N~
*
Cable Type
H05 RR-F ø
3 x 6 mm2 4 x 4 mm2 5 x 2,5 mm2
H05 VV -F
230-240 V ~ 400 V 2N~
1 1
L1
L1
2
2
3 3
L2
4
4
5 5
N N
E
E
E = GREEN and Yellow / N = BLUE / L = BROWN
Ensure that there is sufficient cable allowed for any subsequent removal
of the unit.
SE RVI C E I N S T R U C T I ON S
All service should be carried out be a authorised service technician only.
WARNINGS
Before performing any repair or operation, switch the appliance off.
The manufacturer declines all responsibility for any damage to persons,
animals or things caused by failure to observe the rules indicated above.
OVEN LIGHTS
Always ensure the oven unit is switched off at the
mains before replacing the oven light bulb to avoid
possible electric shock.
To remove the light bulb, unscrew the glass cover
anticlockwise and remove. Turn the bulb
anticlockwise and remove (Fig. 1A). Replace with
the same type of bulb (Type E14 threaded clear
lamp 230/240 V. 25 watt T 300°C). Replace the
light carefully and turn it clockwise.
4
Three phases
connection
400V 3N~
1
L
2
3
4
400 V 3N~
1
L1
N 5
2
L2
3
L3
4
5
N
E
A
Fig. 1A
Fig. 1