Table of Contents
Advertisement
Page 5
Accurate Temperature Regulation
The CZ Infrared™ heating system utilizes state of the art electronics and
internal power sourcing to accept a low‐voltage thermostat of your choosing.
Low voltage wall thermostats provide more accurate temperature control and
can be linked to a central control system if desired.
The unique low‐voltage thermostat controls on a CZ Infrared™ heater allow
the heater to be linked to a central zoned control system without modification
or special switching devices to control the voltage to the heating elements
themselves. This feature allows the CZ Infrared™ system to be operated in the
most economical manner possible by utilizing the infrared heat only in those
spaces which are currently being occupied and require the heat. Zoned
heating is as much as 50% more economical to use when the entire home or
office does not require heat in all areas 100% of the time. The cost savings from
this feature alone makes initial installation of the CZ Infrared™ heating system
pay for itself in a matter of months.
Cost‐Effective to Install
* Components in the CZ Infrared™ heating system are designed to last 10 times
longer than other in‐wall heaters. CZ Infrared™ warranty coverage and service
procedures are simple to follow and they can be serviced in ten minutes or less
should repair be required.
* The cost to purchase and install a CZ Infrared™ infrared heating system for
your entire home is usually much cheaper than the cost of installing a central
forced air heating system.
Stylish & Functional
The CZ Infrared™ heater service panel and wall registers are stylish and
functional with a modest design flare making them more favorable for custom‐
home installation than conventional registers and intake ducts. The designer
panel on the wall register can be left white or custom painted to match or
contrast the walls.
Patented Proprietary Technology
CZ Infrared™ heaters contain a proprietary high‐efficiency, ceramic infrared
emitter ( or heating element) which produces more infrared heat per kilowatt
than conventional ceramic. quartz, or carbon plates.
Customer/Warranty Service: (800) 595-9605
CZ Infrared
Heater Specifications
™
Model CZ‐500F
Cabinet: All Metal –22 & 24 gauge
Weight: 8.0 lbs
3
Dimensions: 18" x 4
/
" x 4" (H,W,D)
8
Power Requirements: 120 Volt AC —500 Watt.
Power Supply: Requires isolated 12 gauge wire to fuse panel.
Chassis Safety Insulation: Exceeds all government and
independent laboratory standards for safety in an installed
heating appliance (a safety standard that exceeds other
manufacturer's specifications).
Internal ceramic blanket provides R45 insulation between the
wall and the heater. The heater cabinet installed in the wall
remains cool to the touch while delivering warm (160° F)
infrared heat into the room.
Life Expectancy: CZ Infrared heaters—25 years+.
Thermostat Power Requirement: None. The unit contains its
own low voltage power supply for thermostat operation.
Thermostat Type: Any 12‐24 volt low‐voltage thermostat (not
supplied).
Zoned Heat Capability: Pre‐wired. Simple two‐wire contact to
any zone control panel—can also accept multiple parallel hook‐ups to a single low‐
voltage thermostat.
Safety Cut‐Off: Yes.
Listed Approvals: CTUV‐US & International (UL Equivalent).
Installation: Any wall with a minimum 3 ½ inches of depth.
Heat Type: Therapeutic far‐infrared heat.
Heat Chamber copper lined for maximum ion transfer.
Heating Elements: One (1) ceramic infrared emitter 500 w.
Ceramic Life Expectancy: Rated at 40,000 hours.
Heat Output: 2,800 BTU infrared heat.
Fan System: One (1) high volume, low noise 90mm DC fan.
Frequency Hum: There is no AC 60Hz frequency hum as with other in‐wall systems.
Fan Noise Level: 18 dB—practically silent.
Warranty: Limited 3 Year P & L. 5 Year—ceramic emitters.
Page 18
CZ-500F
©2009 EarthWise Technologies, Inc
Advertisement
Table of Contents
