Samsung UN19C4000 User Manual page 44

• Wall cable jack
• VHFIUHF Antenna
• Cable or Satellite box
Ant or Cable Out
Connect Ant In to
Make sure the AC power cord is plugged in securely to
the wall outlet and the 1V.
Use a 75 ohm (round) cable. ' " - - - - - - - - '
Step 2:
Connect Antenna or Cable
1-800-SAMSUNG (1-800-726-7864)
Samsung Bectronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
8amsung Bectronics Canada Inc.
ss
Standish Court Mississauga, Ontano L5R 482
Call Center hours of operation: Moo-Sun. 9:00 !WI -12
!WI EST.
To register this product. visit: www.samsung.comI
regISter:
Congratulations on the purchase of your new 8amsung Tv.
Read thiS setup gUIde to get your TV up and running quickly.
Quick Setup Guide
Step I:
Install the Stand
Follow the steps below to connect the 1V to the stand.
~NOTE
• Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
• Make sure that at least two persons lift and move the LED TV.
• Stand the product up and fasten the screws. If you fasten the screws with
the LED TV placed down, it may lean to one side.
Step 4:
Run Plug & Play
When you turn on your 1V for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the 1V's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTER
~
button.
To skip a screen, press the MENU button. To turn on your TV, press the POWER
button on the remote or on the 1V. To run Plug & Play, follow these steps:
Select Home Use, and then
press the ENTER
~
button. If
you select Store Demo, the 1V
will reset your picture and audio
settings every 30 minutes.
Using your remote control, select
the language for the On Screen
Display (OSD), and then press the
ENTER
~
button.
2
Select Antenna Source to
memorize. If Antenna Source is
Cable or Auto, you must select
your cable system type. After
selecting source, select Search; then press the ENTER
~
button on your
remote.
~
Most cable systems are Standard (STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
~
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
3
1
Slide the TV onto the stand
body.
Insert the stand body into the stand
base.
Screw the stand base to the stand
3
body.
2
1
UN26C4000
4
The 1V memorizes the available channels. This process can take up to 45
minutes.
j
Topview :
""",,,("4XU2)
muummu~', ,-"
·"i.@. .
i
Connect the Guide Stand to the
G:~::t~~_~~~~~~---------
...
~
f ••
Stand using four screws (M4
X
L 12) as shown
~
Rear
1111111111111111111111111111111111111111111
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
Select the daylight savings time setting: Off or On, and then press the
ENTER
~
button.
Select the time zone in which you live, and then press the ENTER
~
button.
The Enjoy your
TV.
screen appears. Then press the ENTER
~
button.
After the 1V has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTER
~
button.
~
If you select Manual, the clock setting screen appears.
6
5
9
7
8
If
You Want to Rerun Plug
&
Play
1. Press the SOURCE button on your remote, then select TV mode.
2.
Press the MENU button on your remote to display the menu.
3.
Press the
~
or
T
button to select Setup, and then press the ENTER
~
button.
4. Press ENTER
~
again to select Plug
&
Play.
BN68-02628A-OO
Fasten three screws (M4
X
L8) at
position
0,
and then fasten three
screws (M4
X
L8) at position
8.
3
With your 1V upright, connect the
1V to the Stand as shown.
2
1