Samsung 4 Series Quick Setup Manual

Quick Setup Guide
Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two persons lift and move the LED TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the LED TV placed down, it may lean to one side.
UN19C4000, UN22C4000, UN22C4010
1
Insert the stand body into the stand
base.
2
Screw the stand base to the stand
body.
UN26C4000
1
Connect the Guide Stand to the
Stand using four screws (M4 X
L12) as shown
2
With your TV upright, connect the
TV to the Stand as shown.
Front
Rear
All manuals and user guides at all-guides.com
3
Slide the TV onto the stand
body.
Screws (M4 X L12)
Guide Stand
Stand
Rear
3
Fasten three screws (M4 X L8) at
position 1, and then fasten three
screws (M4 X L8) at position 2.
2
1
Step 2
: Connect Antenna or Cable
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
Using your remote control, select
the language for the On Screen
Display (OSD), and then press the
ENTERE button.
2
Select Home Use, and then
press the ENTERE button. If
you select Store Demo, the TV
will reset your picture and audio
settings every 30 minutes.
3
Select Antenna Source to
memorize. If Antenna Source is
Cable or Auto, you must select
your cable system type. After
selecting source, select Search; then press the ENTERE button on your
remote.
✎
Most cable systems are Standard (STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
The TV memorizes the available channels. This process can take up to 45
minutes.
5
Top view
After the TV has memorized the channels, choose the Clock Mode. Select
Auto if you have a digital channel in your area. Select Manual if you don't, or
if you have a cable or satellite box. When done, press the ENTERE button.
✎
If you select Manual, the clock setting screen appears.
6
Select the daylight savings time setting: Off or On, and then press the
ENTERE button.
7
Select the time zone in which you live, and then press the ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
The Enjoy your TV. screen appears. Then press the ENTERE button.
If You Want to Rerun Plug & Play
1. Press the SOURCE
2. Press the MENU
3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE
button.
VHF/UHF Antenna
Antenna Cable (Not Supplied)
or
Use a 75 ohm (round) cable.
MENU button. To turn on your TV, press the
Select Language of the OSD.
Menu Language
Anrenna Source
Digital Cable System
Analog Cable System
button on your remote, then select TV mode.
button on your remote to display the menu.
Connect Ant In to
• Wall cable jack
• VHF/UHF Antenna
• Cable or Satellite box
Ant or Cable Out
POWER
Plug & Play
English
Español
:
Français
U Move E Enter
Plug & Play
:
Air
:
Cable
Auto
:
Search
U Move E Enter