Table of Contents
Advertisement
WOOD BEL
WOOD BEL
WOOD BEL T SANDER
WOOD BEL
WOOD BEL
6 X 48 INCHES
6 X 48 INCHES
6 X 48 INCHES
6 X 48 INCHES
6 X 48 INCHES
ASSEMBLY AND OPERATING
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
©
Copyright
1999 by Harbor Freight Tools
manual or any artwork contained herein may be reproduced in any shape or
form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
T SANDER
T SANDER
T SANDER
T SANDER
40643
INSTRUCTIONS
®
. All rights reserved. No portion of this
®
Advertisement
Table of Contents
Related Manuals for Central Machinery 40643
Summary of Contents for Central Machinery 40643
- Page 1 T SANDER 6 X 48 INCHES 6 X 48 INCHES 6 X 48 INCHES 6 X 48 INCHES 6 X 48 INCHES 40643 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com ©...
-
Page 2: Specifications
Do not force tool. It will do the job better and more safely at the rate for which it was intended. Do not use inappropriate attachments in an attempt to exceed the tool capacity. REV 01/04; 09/05 SKU 40643 For technical questions, please call 1-800-444-3353. Page 2... - Page 3 19. Avoid causing fires. When sanding metals remove dust collecting bags and hoses from the machine. Sparks or hot metal could start a fire. Clean all wood dust before and after sanding metal. SKU 40643 For technical questions, please call 1-800-444-3353. Page 3...
-
Page 4: Using Extension Cords
Base (46) (for example, the end that the on/off switch is located on.) Place the top of the Leg (74) under the corner of the Base, lining up the REV 01/04 SKU 40643 For technical questions, please call 1-800-444-3353. Page 4... -
Page 5: Operation
If the Table is not 90 degrees with the Pad, loosen the table angle Lock Handle (32) and tilt the Table until the square is flush with the Pad. REV 01/04 SKU 40643 For technical questions, please call 1-800-444-3353. Page 5... - Page 6 Turn the tracking Knobs (66) on both sides of the Idle Roller (64) until the belts rides on the center of the Idle Roller (64) and the Driving Roller (11). Retighten the locking Knob (61). Tracking Knobs (66) Locking Knob (61) Switch (49) REV 12/00 SKU 40643 For technical questions, please call 1-800-444-3353. Page 6...
- Page 7 To lock switch in Off position, pull out the key and store in a secure place. CAUTION: Never walk away from sander when the machine is running. Always lock the switch in the Off position when not in use. REV 09/00 SKU 40643 For technical questions, please call 1-800-444-3353. Page 7...
-
Page 8: Maintenance
1/4 inch give to the V-Belt for proper tension. NOTE: Too much tension on the V-Belt can load-down motor and cause possible damage. If the V-Belt is loose, it may fail prematurely. Replace Pulley Cover (47). SKU 40643 For technical questions, please call 1-800-444-3353. Page 8... -
Page 9: Troubleshooting
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 40643 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Parts List
" 2 " 2 l l u l l o " 4 d i l REV 12/00 SKU 40643 For technical questions, please call 1-800-444-3353. Page 10... -
Page 11: Assembly Drawing
Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available indi- vidually as replacement parts. SKU 40643 For technical questions, please call 1-800-444-3353. Page 11...