1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Wireless Router
  5. DVG-N5402FF
  6. User manual

D-Link DVG-N5402FF User Manual

Voip wireless router
Hide thumbs Also See for DVG-N5402FF:
Table of Contents

Advertisement

Quick Links

Download this manual
DVG-N5402FF
VoIP Wireless Router
User's Manual
Version 1.0
(July 2011)

Advertisement

Table of Contents
loading

Related Manuals for D-Link DVG-N5402FF

Summary of Contents for D-Link DVG-N5402FF

  • Page 1 DVG-N5402FF VoIP Wireless Router User’s Manual Version 1.0 (July 2011)
  • Page 2 Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

  • Page 3: Table Of Contents

    Contents 1. Introduction ..............................4 1-1 Product Overview ............................. 4 1-2 Hardware Description ..........................5 2. Getting Started ..............................8 3. VoIP Router Web Configuration ........................16 3-1 SETUP ..............................16 3-1-1 Internet Setup ..........................16 3-1-2 VoIP Setup ........................... 22 3-1-3 Wireless Setup ..........................

  • Page 4: Introduction

    Internet connection. The DVG-N5402FF can be configured a fixed IP address or it can have one dynamically assigned by DHCP or PPPoE. It adopts either the G.711, G.726, G.729A, G.723.1 or iLBC voice compression format to save network bandwidth while providing real-time, toll quality voice transmission and reception.

  • Page 5: Hardware Description

    Power: Power LED. A steady light indicates a proper connection to a power source. Prov./Alm.: A blinking light indicates the DVG-N5402FF can not register with SIP Server or can not get the IP address. A blinking light also indicates the DVG-N5402FF is attempting to connect with the Provisioning server.

  • Page 6: Rear Panel

    Ground: A conducting connection with the earth. Connect with the ground so as to make the earth a part of an electrical circuit using metal wire. Power Receptor: Receptor for the provided power adapter. Power Switch: Press down to turn-on DVG-N5402FF. WARNING: DO NOT (1) connect the phone ports to each other (FXS to FXS) or (2) connect any phone port directly to a PSTN line (FXS to PSTN) or to an internal PBX line (FXS to PBX extension).
  • Page 7 DVG-N5402FF User’s Manual Telephone Interface Description WPS: WPS button for wireless WPS-PBC setup method. Antenna: Connect to a wireless network. Reset button: Use to restore factory default settings. Use Reset Button to restore factory default settings: 1. Press and hold the reset button for 5 seconds.

  • Page 8: Getting Started

    SETUP 2. Getting Started To access the web-based configuration utility, open a web browser such as Internet Explorer and enter the IP address of the DVG-N5402FF from WAN port. Open your Web browser and type http://192.168.8.254 into the URL address box.
  • Page 9 DVG-N5402FF User’s Manual SETUP Click Setup Wizard. Click Next. D-Link Systems, Inc.
  • Page 10 DVG-N5402FF User’s Manual SETUP The username of ADMIN and USER have been defined and locked by default. It is highly recommended to create a login password to keep your VoIP Router secure. Click Next. D-Link Systems, Inc.
  • Page 11 DVG-N5402FF User’s Manual SETUP Enter a NTP server or use the default server. Select your time zone from the drop-down menu. Enable Daylight Saving for your local time if required. Click Next. D-Link Systems, Inc.
  • Page 12 DVG-N5402FF User’s Manual SETUP Select your Internet connection type: DHCP – Most Cable ISPs or if you are connecting the DVG-N5402FF behind a router. Static IP – Select if your ISP supplied you with your IP settings. PPPoE – Most DSL ISPs.
  • Page 13 DVG-N5402FF User’s Manual SETUP Register to the SIP Proxy Server by clicking Enable support of SIP Proxy Server. Enter Proxy Server IP/Domain and Port. Outbound Proxy Support is optional. To register, please click on the Outbound Proxy Support box and enter Outbound Proxy IP/Domain and Port in it.
  • Page 14 DVG-N5402FF User’s Manual SETUP Click on the Enable wireless LAN interface check box to build a wireless network. Enter the SSID to name your wireless network. All devices must have the same SSID to communicate on the wireless network. Select a clear wireless channel. Select the 802.11 Mode of your network which can work in different speed of wireless connection.
  • Page 15 DVG-N5402FF User’s Manual SETUP Setup is finished. Check the summary of your settings. To make new settings effective, you must click on the Restart button to reboot the DVG-N5402FF. Click Restart D-Link Systems, Inc.

  • Page 16: Voip Router Web Configuration

    DVG-N5402FF User’s Manual SETUP 3. VoIP Router Web Configuration 3-1 SETUP 3-1-1 Internet Setup WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The WAN settings are provided to you by your ISP and oftentimes referred to as "public settings". Please select the appropriate option for your specific ISP.
  • Page 17 DVG-N5402FF User’s Manual SETUP SETUP → Internet Setup SETUP → Internet Setup DHCP: Select this option if your ISP (Internet Service Provider) provides you an IP address automatically. Cable modem providers typically use dynamic assignment of IP Address. The Host Name field is optional but may be required by some Internet Service Providers.
  • Page 18 DVG-N5402FF User’s Manual SETUP SETUP → Internet Setup PPPoE: Select this option if your ISP requires you to use a PPPoE (Point-to-Point Protocol over Ethernet) connection. Enter the PPPoE Account, PPPoE Password and re-enter Password to confirm. SETUP → Internet Setup PPTP: Point-to-Point Tunneling Protocol (PPTP) is a WAN connection.
  • Page 19 SETUP → Internet Setup 3G USB Adapter: 3G/3.5G WISP. Enter Username, Password, Dial Number and APN to connect to Internet via 3G/3.5G WISP. Users could also select a configured WISP from the list and DVG-N5402FF will fill necessary parameter automatically.
  • Page 20 DVG-N5402FF User’s Manual SETUP SETUP → Internet Setup Factory Default MAC Address: The original MAC address of the VoIP Router. Your MAC Address: It is left blank as you log-in via the WAN port. Current MAC Address: It shows the current MAC Address if you ever used the different MAC address from Factory Default MAC Address.
  • Page 21 DVG-N5402FF User’s Manual SETUP VLAN is optional. It works with the Router or Switch that supports VLAN tag. By adding VLAN tag in packets may improve efficiency of voice traffic performance and security. Enable VLAN Tagging: It is to tag the packets for VLAN Router or Switch identifying.

  • Page 22: Voip Setup

    DVG-N5402FF User’s Manual SETUP 3-1-2 VoIP Setup In this section, it supports registration to multiple Proxy Servers which is allowed to choose ITSP by user manually. If any registration problem occurs, please consult your VoIP Service Provider. SETUP → VoIP Setup Clink Edit icon to modify the settings.
  • Page 23 DVG-N5402FF User’s Manual SETUP SETUP → VoIP Setup Enable Support of SIP Proxy Server / Soft Switch: Check the box to register the VoIP Router with SIP proxy server or soft switch. ITSP Name: Enter the name of ITSP. SETUP → VoIP Setup FXS Representative Number registers to Proxy: Number: Enter the representative number for Line 1 and Line 2.
  • Page 24 DVG-N5402FF User’s Manual SETUP SETUP → VoIP Setup Each line registers to Proxy independently: Number: Enter the number, text or number and text in this field. It is the Caller ID for the called party when you make a VoIP call. If you register the VoIP Router to a SIP proxy server, then it should be the number that provided by SIP proxy server.
  • Page 25 Initial Unregister: Check the box to send an unregistered message initially by the VoIP Router and then it will perform a general register process. Unregister All Contacts: DVG-N5402FF will fill “*”(a star) in Contact field in un-register request to release all registered accounts in this DVG-N5402FF.
  • Page 26 DVG-N5402FF User’s Manual SETUP SETUP → VoIP Setup Outbound Proxy Support: Check the box to send all SIP packets to the destined outbound proxy server. An outbound proxy server handles SIP call signaling as a standard SIP proxy server would do. Further, it receives and transmits phone conversation traffic (media) between two communication parties.
  • Page 27 DVG-N5402FF User’s Manual SETUP For example (Example in Taiwan), If Server 1 is local VoIP Service Provider you can refer to Digit Map page for general settings. If Server 2 is global VoIP Service Provider (VoIP STUN, free to dial to some cities free charge) you can set individual dialing plan for VoIP STUN in Number Translation field.

  • Page 28: Wireless Setup

    DVG-N5402FF User’s Manual SETUP 3-1-3 Wireless Setup This section instructs you how to setup your wireless network on the VoIP Router device. Setup Hint: Every device in the same wireless network must use the same SSID. To avoid wireless network overlap, a specific and different channel is needed.
  • Page 29 AP. Access Mode: DVG-N5402FF has ability to serve as two operating modes in wireless network separately. AP: As a wireless AP that allows wireless-equipped stations to communicate with a wired network and the other wireless network for Internet access and resources sharing.

  • Page 30: Wireless Security

    DVG-N5402FF User’s Manual SETUP 3-1-3-2 Wireless Security This section introduces you different ways of wireless security you can setup. It is important to enable secure algorithm to protect your data from eavesdropping by unauthorized wireless users. SETUP -> Wireless Setup -> Wireless Security Select DDID: Select an SSID to configure wireless security mechanism.
  • Page 31 DVG-N5402FF User’s Manual SETUP WEP Authentication Mode SETUP -> Wireless Setup -> Wireless Security (WEP) WEP Key Length: Select 64-bit or 128-bit data encryption. Default Tx Key: You can select one of the keys as active key at a time.
  • Page 32 DVG-N5402FF User’s Manual SETUP WPA Authentication Mode The wireless network can use WPA Authentication to verify whether a wireless device is allowed to access your Access Point or not. You can choose to use Enterprise (RADIUS) method or Personal (Pre-Shared Key).
  • Page 33 DVG-N5402FF User’s Manual SETUP SETUP -> Wireless Settings -> Wireless Security (WPA) Select the type of WPA (WPA, WPA2, WPA2 Mixed), choose the proper security mode according to your wireless network. WPA Authentication Mode: Select Enterprise (RADIUS). WPA Cipher Suite: WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed.
  • Page 34 SSID, BSSID, Channel, Type, Encryption, and Signal through scanning using this Site Survey tools. Example: 1. Select the Wireless AP and click Accept bottom. 2. Enter the password of the Wireless AP and click Apply bottom. 3. Save the configuration and restart DVG-N5402FF. D-Link Systems, Inc.
  • Page 35 SETUP 3-1-3-3 WPS SETUP -> Wireless Setup -> WPS It allows users establish wireless connect between DVG-N5402FF and computers via WPS(Wireless Protect Setup) method. Example for setting Wiresess profile via WPS method on Windows 7. Enter [Network and Sharing Center] Click [Set up a new connection or network] D-Link Systems, Inc.
  • Page 36 DVG-N5402FF User’s Manual SETUP Click [Connect to the Internet] Click [Wireless] D-Link Systems, Inc.
  • Page 37 DVG-N5402FF User’s Manual SETUP Select a Wireless AP. Click [OK] to start setup. D-Link Systems, Inc.
  • Page 38 SETUP Enter the 8-digit PIN from DVG-N5402FF label then click Next. Note: If you have ever click “Change PIN” button on the WEB UI of DVG-N5402FF, please enter the PIN number displaied on WEB GUI. Type network name(SSID) then click Next.
  • Page 39 SETUP Wait for Windows 7 setting up wireless network. Configuration finished, you could connect to DVG-N5402FF at present. You could also print security key of save this profile for another computer to add this wireless network manually. Note: DVG-N5402FF supports WPS work with WindowsR Vista and Windows 7 only.

  • Page 40: Lan Setup

    DVG-N5402FF User’s Manual SETUP 3-1-4 LAN Setup SETUP → LAN Setup LAN Port Address: Enter the LAN IP address of the VoIP Router. It is also the default gateway for DHCP clients. Subnet Make: Enter the subnet mask for DHCP clients.
  • Page 41 DVG-N5402FF User’s Manual SETUP SETUP → LAN Setup Enable DHCP Server: This variable is to assign the IP address for the devices connected to LAN port of the VoIP Router. IP Pool Starting Address: Enter the starting IP address for the DHCP server's IP assignment.
  • Page 42 DVG-N5402FF at the bridged LAN port you must enter WAN port IP. VLAN ID: Assign a VLAN ID for DVG-N5402FF to transit traffic through-out at WAN port for WAN-LAN bridge mode. The packets are un-tagged at LAN port and added tag at WAN port.

  • Page 43: Usb Settings

    DVG-N5402FF User’s Manual SETUP 3-1-5 USB Settings SETUP → USB Settings USB Type: Select a USB device type. 3G USB Adapter: It allows you plug in a 3G dungle dial to WISP for Internet access. Share Port: Connect USB device such as a printer, scanner or MFP(Multifunction Printer) to DVG and share it at Local Area Network.

  • Page 44: Time And Date

    DVG-N5402FF User’s Manual SETUP 3-1-6 Time and Date SETUP → Time and Date Automatically synchronize with Internet time servers: The VoIP Router should automatically sync up with time servers. First NTP time server: Select the desired domain name of a NTP server as first priority.

  • Page 45: Advanced

    DVG-N5402FF User’s Manual ADVANCED 3-2 ADVANCED 3-2-1 VoIP 3-2-1-1 Caller Filter This function allows you to accept or reject any incoming call from the IP address listed in the filter rule. The call from the IP address of SIP proxy server is always accepted, despite Deny is selected or the IP address of SIP proxy server is not in the filter rule of Allow.
  • Page 46 DVG-N5402FF User’s Manual ADVANCED 3-2-1-2 Caller ID ADVANCED → VoIP → Caller ID FXS Caller ID Generation: Select DTMF, FSK or FSK+Type II Caller ID to enable the caller ID display function on FXS port. When enabled, the caller’s phone number will be displayed on your phone set when the call comes through.

  • Page 47: Calling Features

    DVG-N5402FF User’s Manual ADVANCED 3-2-1-3 Calling Features ADVANCED → VoIP → Calling Features Do Not Disturb: Check the box to reject (busy tone played) incoming calls. Unconditional Forward: Check the box to forward incoming calls to the assigned “Forwarding Number”...
  • Page 48 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → Calling Features Enable Call Feature Code: Check the box to enable/disable some call feature codes through a phone set. Call pickup: Allow one to pick up someone else’s telephone call. Call Back on Busy: Your phone will ring back the last number that called you.
  • Page 49 DVG-N5402FF User’s Manual ADVANCED Calling Feature Instructions: Call Hold: The call will be held after the FLASH button is pressed on the phone set. The VoIP Router will play a hold music (provided by your ITSP or VSP) to the remote end.
  • Page 50 DVG-N5402FF User’s Manual ADVANCED 3-2-1-4 Codec ADVANCED → VoIP → Codec Jitter Buffer: Enter the jitter of receiving packets. Silence Detection / Suppression: Check the box to enable the silence packets and send less voice data (package) during the silent period while talking.
  • Page 51 3-2-1-5 CPT/Cadence ADVANCED → VoIP → CPT / Cadence CPT # 1 Enable Setting 1: Define the call process tones for the DVG-N5402FF generates. ADVANCED → VoIP → CPT / Cadence FXS Ring Cadence Settings: Specify the ring cadence for the FXS port. In this field, you specify the on and off pulses for the ring.

  • Page 52: Digit Map

    DVG-N5402FF User’s Manual ADVANCED 3-2-1-6 Digit Map Digit Map supports multiple dial plans which help users to arrange least cost route. Each Proxy Server has individual dial plan which combines the original feature of Digit Map and Speed Dial. You can use “?” or “%”...
  • Page 53 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → Digit Map → VoIP Route Profile There are 10 VoIP route profiles. Each VoIP route profile provides four routes to select. Server 1, Server 2, Server 3, Phone Book and None can be selected for each route.
  • Page 54 DVG-N5402FF User’s Manual ADVANCED Example 1 – Single VoIP route, The number translation of each server is blank. The VoIP route profile appears like: Digit Map Table appears like: As you dial the phone numbers starting with 09, like 0912345678, the call will only go through Server 1 (local VSP).
  • Page 55 DVG-N5402FF User’s Manual ADVANCED Example 2 – Multiple Route, The number translation of Server 1 is blank, and the number translation of Server 2 appears like: The VoIP route profile appears like: Digit Map Table appears like: As you dial the phone numbers staring with 03, like 0312345678, the number will be changed to 0045312345678, followed the number translation of Server 2, and the call will go through Server 2 (free VSP) at first.
  • Page 56 DVG-N5402FF User’s Manual ADVANCED Example 3 – Multiple Route, The number translation of Server 1 is blank, and the number translation of Server 2 appears like: The number translation of Server 3 appears like: The VoIP Route Profile appears like:...
  • Page 57 DVG-N5402FF User’s Manual ADVANCED Digit Map Table appears like: As you dial the phone numbers staring with 00244, like 00244123456789, the number will be changed to 0123456789 followed the number translation of Server3, and the call will go through Server 3 (UK VSP) at the first.
  • Page 58 DVG-N5402FF User’s Manual ADVANCED For example, Scan Code: 09 VoIP Dial-out: 0912345678 User Dial Length: 2 Route: Auto VoIP Route Profile: Route # 1 Pick up the handset and dial 09, and the system will do the things as follow: 1.
  • Page 59 DVG-N5402FF User’s Manual ADVANCED 3-2-1-7 DTMF & PULSE ADVANCED → VoIP → DTMF & PULSE Dial Wait Timeout: Enter the timeout duration after the user picks up the phone set. Inter Digits Timeout: Enter the timeout duration between the intervals of each key pressed. When exceeding the set timeout duration without entering further digits, the numbers entered will be dialed out.
  • Page 60 DVG-N5402FF User’s Manual ADVANCED 3-2-1-8 Fax ADVANCED → VoIP → FAX Option Fax Detection Content of SDP of re-INVITE re-INVITE with T.38 from remote party Disable Accept and change RTP to T.38 T.38 Fax re-INVITE with T.38 and T.30 Accept and change RTP to T.38 T.30 Fax...
  • Page 61 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → FAX Switch FAX On CED Detection: DVG will send FAX Re-Invite immediately as it detect FAX CED tone, that will save handshaking time between FAX machines. Restrict T.38: DVG will reject T.38 Re-invite in case the FAX type contains without T.38.
  • Page 62 DVG-N5402FF User’s Manual ADVANCED 3-2-1-9 Hot Line ADVANCED → VoIP → Hot Line Hot Line: Check to direct the call automatically to a pre-configured destination without any action when the FXS is off-hook. (ie. as the user picks up the phone). When the FXS is under Hot Line mode, no other phone numbers can be dialed.
  • Page 63 DVG-N5402FF User’s Manual ADVANCED 3-2-1-10 Line ADVANCED → VoIP → Line Enable: Tick the check box to enable a line. If some lines are not used, disable them (Pause Function) to avoid unnecessary waiting when an incoming call is diverting to the line.
  • Page 64 Metering Pulse Type/ Metering Pulse Period: It is used for telephony device which connected to FXS port for billing purpose. DVG-N5402FF provide 14k Hz and 16k Hz metering capacity. The fully support for detail Metering Pulse Period is not free charge, please contact with your vendor.
  • Page 65 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → Line FXS Impedance: Select different impedance from the drop-down menu. ADVANCED → VoIP → Line This feature is a call drop standard for a VoIP Router to determine whether or not to hang up the phone.
  • Page 66 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → Line Enable IVR Option: Check the box to enable IVR function. ADVANCED → VoIP → Line Hunting/Ring: It is used to set FXS group hunting mode. There are Hunting, Simultaneous Ring and Sequential Ring.

  • Page 67: Phone Book

    DVG-N5402FF User’s Manual ADVANCED 3-2-1-11 Phone Book Phone Book: It is used for peer-to-peer communication. Some peer information needs to be added to this section prior to making peer-to-peer calls. You need to enter the phone number and the IP address of the remote peer.

  • Page 68: Sip Advanced

    9002 and 9003, and so forth. SIP Transport Protocol: DVG-N5402FF supports UDP, TCP and TLS for SIP signaling. Most of SIP Server support UDP, if you prefer TCP or TLS please make sure whether remote party supports TCP/TLS or not.
  • Page 69 DVG-N5402FF User’s Manual ADVANCED Note: E.164 Numbering depends on the proxy. If you fail to make a call, please contact your VoIP Service Providers. ADVANCED → VoIP → SIP Advanced Session Expiration: This field will set the time that the VoIP Router will allow a SIP session to remain die (without traffic) before dropping it.
  • Page 70 DVG-N5402FF User’s Manual ADVANCED ADVANCED → VoIP → SIP Advanced Anonymous Caller ID (CLIR): Check the box to lock the delivery of the Caller ID to the called party. VoIP Call Out Notification: Check the box to enable the function of playing a tone to notify user that the call is through VoIP.
  • Page 71 INVITE. Different format of INVITE header might cause the call not to be connected. Please consult with your VoIP Service Provider before enabling it. Callee Quick Media: DVG-N5402FF will send RTP to remote party immediately as user answer an inbound call.

  • Page 72: Access Control

    DVG-N5402FF User’s Manual ADVANCED 3-2-2 Access Control 3-2-2-1 MAC Filtering Use MAC Filters to deny computers within the local area network from accessing the Internet. You can either manually add a MAC address that are connected to the VoIP Router.

  • Page 73: Firewall And Dmz

    DVG-N5402FF User’s Manual ADVANCED 3-2-3 Firewall and DMZ 3-2-3-1 DMZ DMZ (Demilitarized Zone) allows the server on the LAN site to be directly exposed to the Internet for accessing data and to forward all incoming ports to the DMZ Host. Adding a client to the DMZ may expose that computer to a variety of security risks;...

  • Page 74: Dos Prevention

    DVG-N5402FF User’s Manual ADVANCED 3-2-3-2 DoS Prevention ADVANCED → Firewall and DMZ → DoS Prevention Enable DoS Prevention: Check the box to prevent DoS attacks from WAN or LAN. There are various types of DoS attacking. Leave settings in this field to the default if you are not familiar with it.
  • Page 75 DVG-N5402FF User’s Manual ADVANCED 3-2-3-3 IP Filtering Use IP Filters to deny particular LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for a specific IP address. The screen will display well-known ports that are defined. To use them, click on the edit icon.

  • Page 76: Port Filtering

    DVG-N5402FF User’s Manual ADVANCED 3-2-3-4 Port Filtering Port filtering enables you to control all data that can be transmitted over routers. When the port used at the source end is within the defined scope, it will be filtered without transmission.

  • Page 77: Virtual Server

    DVG-N5402FF User’s Manual ADVANCED 3-2-3-5 Virtual Server Enable users on Internet to access the WWW, FTP and other services from your NAT. It is also known as port forwarding. When remote users are accessing Web or FTP servers through WAN IP address, it will be routed to the server with LAN IP address.

  • Page 78: Advanced Wireless

    DVG-N5402FF User’s Manual ADVANCED 3-2-4 Advanced Wireless 3-2-4-1 Advanced This section introduces advanced configuration for the wireless access point. If you are not familiar with the following functions, keep the default parameters. In some cases, incorrect settings may reduce wireless performance.
  • Page 79 DVG-N5402FF User’s Manual ADVANCED 3-2-4-2 Access Control The Access Control setting provides a service that you can control different access rights for different wireless clients connected to your VoIP Router. The local and remote stations are limited to access Internet through your Access Points using MAC address of wireless client.

  • Page 80: Advanced Network

    DVG-N5402FF User’s Manual ADVANCED 3-2-5 Advanced Network 3-2-5-1 QOS WAN QoS ADVANCED → Advanced Network → QoS Enable WAN QoS: Check the box to guaranty the voice quality. The system reserves the bandwidth for voice packets, and the data transmission is distributed to less bandwidth.

  • Page 81: Nat Traversal

    DVG-N5402FF User’s Manual ADVANCED 3-2-5-2 NAT Traversal If your VoIP Router is set up behind an Internet sharing device, you can select either the NAT or STUN protocol. ADVANCED → Advanced Network → NAT Traversal Enable NAT Public IP: Check the box to use the IP address of the Internet sharing device if the VoIP Router is set up behind an Internet sharing device.

  • Page 82: Stun Inquiry

    DVG-N5402FF User’s Manual ADVANCED 3-2-5-3 STUN Inquiry Use “STUN Inquiry” to detect your IP sharing device’s NAT type and communication between a STUN server and client. ADVANCED → Advanced Network → STUN Inquiry NAT Type: It shows the NAT type of your router.

  • Page 83: Static Route

    DVG-N5402FF User’s Manual ADVANCED 3-2-5-4 Static Route Build static routes within an internal network. These routes will not apply to the Internet. ADVANCED → Advanced Network → Static Route Route: Destination network of the route. Route Mask: Subnet mask to apply on destination network.
  • Page 84 DVG-N5402FF User’s Manual ADVANCED 3-2-5-6 RIP ADVANCED → Advanced Network → RIP Enable RIP: Check the box to enable RIP to build small-multi router network via RIP protocol. This function is useless for home network. D-Link Systems, Inc.

  • Page 85: Snmp

    3-2-6 SNMP ADVANCED → Advanced Network → SNMP DVG-N5402FF supports SNMP V1, V2 and V3. Please enter required parameter for SNMP V3 on each SNMP setting pages. If the MIB browser supports SNMP V1 and V2 only, please refer to following configuration:...
  • Page 86 DVG-N5402FF User’s Manual ADVANCED  Set [Advanced-> SNMP Management-> SNMP View-> View Name] as “all”. Set [Advanced-> SNMP Management-> SNMP View-> View Name] as “.1”   Set [Advanced-> SNMP Management-> SNMP Community-> Community Name] for public and private. ...
  • Page 87 DVG-N5402FF User’s Manual ADVANCED D-Link Systems, Inc.

  • Page 88: Maintenance

    DVG-N5402FF User’s Manual MAINTENANCE 3-3 MAINTENANCE 3-3-1 Device Management MAINTENANCE → Device Management Note: There are two operating levels when entering the Web UI. Logging-in as the ADMIN allows you to change all settings. A Web UI USER only has access to some settings.

  • Page 89: Backup And Restore

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-2 Backup and Restore Save and Reboot MAINTENANCE → Backup and Restore Save All Settings: Click the Save All Settings check box and reboot the system after completing changes. The new settings will take effect after the VoIP Router is restarted.

  • Page 90: Update Settings

    DVG-N5402FF User’s Manual MAINTENANCE Backup Configurations Template File MAINTENANCE → Backup and Restore Click the Backup Settings button to save your current settings to a template file for editing. Update Settings MAINTENANCE → Backup and Restore To restore a system settings file, click on Browse to search the local hard drive for the file to be used. Once you locate the file, click Upload Settings to overwrite the current settings with the settings saved to the file.

  • Page 91: Firmware Update

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-3 Firmware Update The VoIP Router supports a software upgrade function from a remote server. Please consult your VoIP Service Provider for information about the following details. MAINTENANCE → Firmware Update Upgrade Server: Select the upgrade type: TFTP, FTP, or HTTP.

  • Page 92: Dynamic Dns

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-4 Dynamic DNS ADVANCED → Dynamic DNS Enable Dynamic DNS: Check the box to enable DDNS function. It is only necessary when the VoIP Router is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS.

  • Page 93: Log Settings

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-5 Log Settings MAINTENANCE → Log Settings Enable: Check the box to send event notification messages across IP networks to the Server. Server Address: Enter the System Log Server’s IP address. Port: Enter the System Log Server’s listening port. Leave this field to the default if your VoIP Service Provider did not provide you a server port number for System Log Server.

  • Page 94: Diagnostics

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-6 Diagnostics 3-3-6-1 Ping Test Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the remote host. The result would be shown on Result Table MAINTENANCE →...
  • Page 95 MAINTENANCE 3-3-6-2 Outward Test MAINTENANCE → Diagnostics → Outward Test It allows operator to verify whether it is some problem on the cable between phone sets and DVG-N5402FF FXS ports. Enable: Select the lines you want to test. Including Channel In Used: Since the line test will interrupt a talking call, that DVG-N5402FF will ignore the in used line.
  • Page 96 Enable: Select the lines you want to test. Including Channel In Used: Since the line test will interrupt a talking call, that DVG-N5402FF will ignore the in used line. If you would like to test all the lines you select even it is in used, please tick this item.

  • Page 97: Tr069

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-7 TR069 TR069 allows operator to manage DVG-N5402FF with a TR069 standard protocol. Note: Fill in the parameters needed by your VoIP Service Provider. Please check with your VoIP Service Provider about the availability of these services.
  • Page 98 DVG-N5402FF User’s Manual MAINTENANCE Connection Request Username: Enter username for remote trigger. Connection Request Password: Enter password for remote trigger. Note: Contact your server provider if necessary. MAINTENANCE → TR069 Binding Server for Trigger: Check the box to trigger a connection between Provisioning Server and the VoIP Gateway.

  • Page 99: Cdr

    DVG-N5402FF User’s Manual MAINTENANCE 3-3-8 CDR The user can set up a CDR Server to record call details for every phone call with TCP protocol. The present CDR provides the call event such as HOOK ON, HOOK OFF, DIALED NUMBER, DATE…recording in a text file and which can be imported to prepare an analysis report.

  • Page 100: Status

    DVG-N5402FF User’s Manual STATUS 3-4 STATUS 3-4-1 Device Info STATUS → Device Info For WAN Port Information, it shows IP address, subnet mask, default gateway and DNS server. If you use PPPoE to obtain IP, you will know if the IP is obtained through this method. If IP address, subnet mask, default gateway is blank, it means that the VoIP Router does not obtain IP.

  • Page 101: Voip Status

    DVG-N5402FF User’s Manual STATUS 3-4-2 VoIP Status STATUS → VoIP Status For Port Status, it includes if each port registers to Proxy successfully, the last dialed number, how many calls each port has made since the VoIP Router is start, etc.

  • Page 102: Lan Client

    LAN interface. The DHCP Clients table displayed LAN device that has already been assigned an address from DVG-N5402FF. You can check if the DHCP client has obtain an IP address. STATUS → LAN Client D-Link Systems, Inc.

  • Page 103: Statistics

    DVG-N5402FF User’s Manual STATUS 3-4-4 Statistics STATUS → Statistics Display the information of the last call made. Press Refresh button to get the latest RTP Packet Summary. 3-4-5 Routing Table STATUS → Routing Table The Routing Table stores the information for particular network destination around the VoIP Router. Press Refresh button to generate the details.

  • Page 104: Logout

    DVG-N5402FF User’s Manual STATUS 3-4-6 Logout If setting or parameter has been changed, remember to save the changes before you logout the configuration menu. Logout D-Link Systems, Inc.

  • Page 105: Configuring The Voip Router Through Ivr

    DVG-N5402FF User’s Manual VoIP Router Configuration-IVR 4. Configuring the VoIP Router through IVR VoIP transmits voice data (packets) via the Internet, hence the condition and status of the network environment is relatively important to the telecommunications quality. If any one of the parties involved in VoIP communications has insufficient bandwidth or frequent packet loss, the telecommunication quality will be poor.
  • Page 106 DVG-N5402FF User’s Manual VoIP Router Configuration-IVR Once the setting or query has been completed, you can hear a dial tone. Use the same procedure to make a second query or setting. To exit IVR mode, simply hang up the phone.

  • Page 107: Ivr Functions Table

    DVG-N5402FF User’s Manual VoIP Router Configuration-IVR 4-1-1 IVR Functions Table: Function Description Example / Notes Code 111/101 WAN Port IP address Set/Query Dial function code 114 and then dial 1 for a Static IP connection then 112/102 WAN Port Subnet Mask Set/Query setup the IP address.

  • Page 108: Ip Configuration Settings

    DVG-N5402FF User’s Manual VoIP Router Configuration-IVR 4-2 IP Configuration Settings—Set the IP Configuration of the WAN Port Static IP Settings Note: Complete static IP settings should include a static IP (option 1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your Internet Service Provider (ISP) if you have any question.
  • Page 109 DVG-N5402FF User’s Manual VoIP Router Configuration-IVR Select a PPPoE After entering IVR mode, dial 114. When voice prompt plays “Enter value,” dial 3 (to select PPPoE). PPPoE Account Settings After entering IVR mode, dial 121. When voice prompt plays “Enter value”, enter the account number followed by”#”.

  • Page 110: Pppoe Character Conversion Table

    (high-lighted) of each pair of the column (“Input Key”) represents the codes to be entered for the corresponding numbers, alphabets or symbols. For example, to enter “D-Link” according to the table below, enter: 148322495451 Numbers...

  • Page 111: Dialing Principles

    DVG-N5402FF User’s Manual Appendix 5. Dialing Principles 5-1 Dialing Options Dial the phone number which you want to call and press # to call out immediately. Note that if the “# (pound)” not dialed, the number will be called out after 4 seconds by default. The period between number dialed and call out is named “Inter Digits Timeout”.

  • Page 112: Routing

    DVG-N5402FF User’s Manual Appendix 5-3 Routing To achieve maximum flexibility, the number dialed will be looked up in several tables defined by VoIP Router. If no match is found from Digit Map Table, it will then look up the number from another table and to the registered VoIP Service Provdier.
  • Page 113 DVG-N5402FF User’s Manual Appendix Start Enter a phone number (D#) Is (D#) defined Change the number to in Digit Map Global Number. table? Is (D#) or Global Number defined in Phone Book table? Is (D#) or Global Number defined in Server 1?

  • Page 114: Appendix

    DVG-N5402FF User’s Manual Appendix Appendix Product Features  One 10/100Mbps auto-negotiation, auto-crossover RJ-45 Ethernet port  Support static IP, PPPoE, and DHCP address assignment and dynamic DNS (DDNS)  QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP signaling and RTP ...
  • Page 115 DVG-N5402FF User’s Manual Appendix Configuration & Maintenance  Configuration methods: Telnet  Status reports: Port status Registration status Ping tests Hardware / software information  Firmware Upgrade through TFTP, FTP or HTTP server  Configuration Backup/Restore  Reset button (with restore factory default function)

Table of Contents