C VO on the DVDM Assy. Therefore, when short-circuit between the emitter and collector of XV-EV61/DLXJ/NC these transistors or the base voltage is supplied for transistors turn on, the laser oscillates. (failure mode) • In the test mode ∗ , there is the mode that the laser oscillates except for the disc judgment and playback.
Page 3
Other formats, including DVD-Audio, DVD-RAM, DVD-ROM, CD-ROM (except those that contain MP3 and WMA files), SACD will not play. DVD-Video DVD-RW DVD-R Audio-CD Video-CD CD-R * CD-RW * Super Video CD (Super VCD) Fuji Color-CD XV-EV61...
SYSTEM SETUP TOP MENU TUNE + DVD SETUP DVD MENU ENTER SOUND MODE RETURN TUNE – ¡ FOLDER – FOLDER + ¢ PROGRAM REPEAT RANDOM CLEAR TEST TONE CH LEVEL SLEEP ENTER TV CONTROL INPUT CHANNELVOLUME SHIFT SELECT Yellow Junction XV-EV61...
Page 7
XHA3137 NSP 15 Dry Cell Battery (AA/R6) VEM1031 Packing Case See Contrast table (2) (2) CONTRAST TABLE XV-EV61/DLXJ/NC and XV-EV31/DLXJ/NC are constructed the same except for the following : Mark No. Symbol and Description XV-EV61/DLXJ/NC XV-EV31/DLXJ/NC Packing Case XHD3355 XHD3360...
2.2 EXTERIOR SECTION XV-EV61 Only To Cassete Deck Refer to "2.4 LOADING MECHA. ASSY". Refer to "2.4 FRONT PANEL SECTION". Refer to "2.3 AMP SECTION". XV-EV61...
Page 9
Rivet AEC7205 FFC Barrier A XEC3048 Tray Cap Assy XXG3155 FFC Barrier B XEC3053 (2) CONTRAST TABLE XV-EV61/DLXJ/NC and XV-EV31/DLXJ/NC are constructed the same except for the following : XV-EV61/ XV-EV31/ Mark Symbol and Description DLXJ/NC DLXJ/NC IF_AF Assy XWZ3726...
Page 11
XEC3050 Primary Holder XMR3084 Push Rivet XEC3034 • • • • • • • • (2) CONTRAST TABLE XV-EV61/DLXJ/NC and XV-EV31/DLXJ/NC are constructed the same except for the following : XV-EV61 XV-EV31 Mark Symbol and Description /DLXJ/NC /DLXJ/NC E-VOL Assy...
Page 13
DECK Door Assy XZN3136 Display Button L XAD3165 Display Button R XAD3166 (2) CONTRAST TABLE XV-EV61/DLXJ/NC and XV-EV31/DLXJ/NC are constructed the same except for the following : Mark No. Symbol and Description XV-EV61/DLXJ/NC XV-EV31/DLXJ/NC MIC Assy XWZ3730 XWZ3734 14 Grille Panel A...
Carriage DC Motor / 0.3W VXM1105 Screw JGZ17P028FMC Flexible Cable (26P) VDA1944 Screw Z39-019 Connector Assy 2P VKP2286 Tray VNL1920 Float Rubber VEB1351 Belt VEB1330 Stabilizer VNE2253 Loading Base VNL1917 Float Base DVD VNL1918 Drive Cam VNL1919 Gear Pulley VNL1921 Loading Gear VNL1922 XV-EV61...
Page 15
Rear View Daifree Daifree No. 23 GEM1036 No. 23 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 XV-EV61...
Page 19
Plate HD Blk F513-847 Roller Pinch Blk R F514-133 Roller Pinch Blk L F514-134 Clutch Assy Blk F522-063 Motor Main Blk F525-334 PCB Control Blk F567-705 11P F. F. C / 30V XDD3142 18P F. F. C / 30V XDD3138 XV-EV61...
Page 29
: The power supply is shown with the marked box. (TX) : AUDIO SIGNAL ROUTE (TUNER) (AM) : AM SIGNAL ROUTE (FM) : FM SIGNAL ROUTE (AM) (TX) (FM) (TX) (TX) CN201 (TX) (FM) (FM) (TX) (AM) L201 ATE7003 XV-EV61...
Page 33
: S VIDEO SIGNAL ROUTE (C) (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO SIGNAL ROUTE (DIGITAL) (DVD) : AUDIO SIGNAL ROUTE (DVD_L ch) (AD) (C/V) (C/V) (DVD) (DVD) XV-EV31 Only (C/V) (C/V) (CY/G) (PB/B) (PR/R) XV-EV31 Only XV-EV61 Only XV-EV61 Only XV-EV61...
Page 35
DVDM ASSY : The power supply is shown with the marked box. (AWM7808/XV-EV61) (AWM7809/XV-EV31) (Cr/R) : VIDEO SIGNAL ROUTE (Cr/R) (CY/G) : VIDEO SIGNAL ROUTE (CY/G) (Cb/B) XV-EV31 Only : VIDEO SIGNAL ROUTE (Cb/B) (C/V) (C/V) (C/V) (C/V) (Cr/R) (Cr/R)
Page 37
: The power supply is shown with the marked box. (PB) (PB) (PB) (REC) EV61:-16.3dBV EV31:- 6.5dBV (REC) EV-61 EV-31 SIGNAL ROUTE (PB) : PB SIGNAL (REC) : RECORDING SIGNAL CN2506 CN5801 XV-EV61...
3.9 IF/AF ASSY(1/3) IF/AF ASSY (XWZ3726/ XV-EV61) XV-EV61 (XWZ3733/ XV-EV31) Only XV-EV61 CN5502 Only CN5507 CN5506 XV-EV61 Only CN5505 from Secondary Assy CN901 XV-EV61...
Page 39
CN903,CN902 XV-EV61 Only EV61 : The power supply is shown with the marked box. (S_Y) CN5701 (S_C) XV-EV31 Only (TX) CN5501 CN5503 CN5801 XV-EV31 Only SIGNAL ROUTE (CD) : CD AUDIO SIGNAL ROUTE : V SIGNAL ROUTE (TX) (S_C) : AUDIO SIGNAL ROUTE (TUNER)
3.10 IF/AF ASSY(2/3) (CD) (AUX) (AUX) (TX) (CD) (TX) XV-EV31 Only (PB) (CD) XV-EV31 Only XV-EV61 Only (REC) (TX) XV-EV61...
Page 41
(REC) (MIC) : RECORDING SIGNAL : MIC OUT SIGNAL (TX) : AUDIO SIGNAL (TUNER) (CD) : CD SIGNAL J5401 CN5105 IF/AF ASSY (XWZ3726 / XV-EV61) (XWZ3733 / XV-EV31) (MIC) (MIC) (TX) (REC) (TX) (REC) EV31 Only XV-EV61 Only (REC) (REC) : The power supply is shown with the marked box.
3.11 IF/AF ASSY(3/3) SIGNAL ROUT (TX) : AUDIO SIGNAL (TUNER) (TX) (TX) XV-EV61...
Page 43
XV-EV61 IF/AF ASSY Only (XWZ3726 / XV-EV61) (XWZ3733 / XV-EV31) CN8302 CN8303 (TX) (TX) : The power supply is shown with the marked box. XV-EV61...
3.13 DSP ASSY (2/2) DSP ASSY (AWX8254) XV-EV61 : Only (AD) (AD) (AD) (AD) (AD) (AD) (AD) (AD) CN5507 : The power supply is shown with the marked box. XV-EV61...
Page 47
: AUDIO SIGNAL ROUTE (DIGITAL) (AD) : AUDIO DATA SIGNAL ROUTE (AD) (AD) (AD) (AD) (AD) (AD) (AD) (AD) XV-EV61...
3.18 SP-TERMINAL and TRADE ASSYS SP-TERMINAL ASSY (XWZ3737 / XV-EV61) (XWZ3742 / XV-EV31) (FL) (FL) (SW) (SL) (SL) (SL) : The power supply is shown with the marked box. XV-EV61...
Page 57
TRADE ASSY (XWZ3740 / XV-EV61) (XWZ3745 / XV-EV31) (SL) (FL) (SL) (FL) (FL) : FL AUDIO SIGNAL ROUTE (SL) : SL AUDIO SIGNAL ROUTE : C AUDIO SIGNAL ROUTE XV-EV61...
Page 59
PRIMARY ASSY (XWZ3738) REK1029 AC IN • NOTE FOR FUSE REPLACEMENT FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION - REPLACE WITH SAME TYPE AND RATINGS ONLY. XV-EV61...
Page 61
REPLACE ONLY WITH SAME TYPE NO. 491007 FOR IC21 AND IC22 MFD, BY LITTELFUSE INC. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491010 FOR IC11 AND IC12 MFD, BY LITTELFUSE INC. XV-EV61...
SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator SIDE A SIDE B LOAB ASSY (VNP1910-A) LOAB S101 LOAD+ VWG2426- CN602 CN602 C102 LOAD- PYKC F6 VNP1910- C101 CN601 CN601 CN602 CN601 CN601 CN602 CN103 LOADING MOTOR ASSY XV-EV61...
4.2 FM/AM TUNER MODULE SIDE A FM/AM TUNER MODULE SIDE A CN5701 CN201 (ANP7338-B) Q202 FM/AM TUNER MODULE SIDE B (ANP7338-B) Q201 IC201 Q203 Q205 IC202 Q204 XV-EV61...
4.6 MIC ASSY SIDE A SIDE A MIC ASSY CN5105 VR5401 W417 C5416 C5420 C5422 W419 C5431 J5401 JA5402 JA5401 C5409 W418 MIC ASSY (XNP3071-B) IC5401 IC5402 SIDE B MIC ASSY (XNP3071-B) Q5403 IC5401 Q5401 IC5402 XV-EV61...
4.11 MOD. AMP ASSY SIDE A SIDE A MOD. AMP ASSY DC FAN MOTOR CN3651 Q3384 CN3022 Q3383 IC3303 IC71 IC3301 CN3021 Q3654 IC81 IC3401 (ANP7461-A) XV-EV61...
4.12 PRIMARY ASSY SIDE A SIDE A PRIMARY ASSY IC5508 (XNP3072-B) AC IN T1 POWER TRANSFORMER XV-EV61...
Page 85
SIDE B SIDE B PRIMARY ASSY IC5508 SECONDARY SIDE ALL EXCEPT NK W132 W111 MY/NV/NK DD/DBD/DL /YPW WIRE PRIMARY MY/NV/NK SIDE DD/DBD/DL KUC/JP (XNP3072-B) XV-EV61...
C9041 IC41 BOND IC21 7.SUBAC1 C9023 C9021 W204 IC21 6.SUBAC1 5.BHAC2 4.BLAC2 IC22 3.GND 2.BLAC1 IC22 1.BHAC1 BOND IC12 IC12 IC11 OPEN SIDE FRONT IC11 W202 BOND R9011 ATTENTION REMPLACER LE IC LINKS COMME INDIQUE.DE CHEZ LITTELFUSE INC. (XNP3072-B) XV-EV61...
Page 87
SIDE B SIDE B SECONDARY ASSY SEC ASSY IC23 XWZ3739 IC25 XWZ3743 491007 IC41 IC41 IC21 7.SUBAC1 6.SUBAC1 5.BHAC2 IC21 4.BLAC2 IC22 3.GND 2.BLAC1 1.BHAC1 IC22 IC12 IC12 IC11 IC11 CAUTION REPLACE IC LINKS AS MARKED.MFD BY LITTELFUSE INC. (XNP3072-B) XV-EV61...
P3 L (CN2507) P1 R (CN2507) VR2401 L ch Repeat recording, playback and REC = STD–633 test tape and record/ (DECK ASSY) adjustment until playback level of the playback the 315Hz signal. PLAY VR2402 R ch 315Hz signal becomes –7.7dBV±0.5dB. XV-EV61...
Page 103
SIDE A CN2302 OPEN VR2301 (Lch) VR2401 (Lch) VR2401 VR2402 VR2302 (Rch) REC LEVEL PB LEVEL VR2402 VR2301 VR2302 (Rch) MECHANISM UNIT CN2507 (DECK TP) FWD Azimuth REV Azimuth Adjustment Screw Adjustment Screw Fig. 6-3 Adjustment and Measurement Points XV-EV61...
[Electrical Part] screw screw Electrical adjustments are not required. 6.4 JIGS and MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1381) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) XV-EV61...
Exchange the Traverse Mechanism point Electric point ∗ After adjustment, screw locks Mechanical Ÿ Exchange the Spindle Motor point with the Screw tight. Electric point Exchange PCB Assy Mechanical Exchange PC Board point LOAB and DVDM ASSY Electric point XV-EV61...
Perform only trace, video and audio outputs are nothing. < When playback with the target address of disc (DVD)> For example, when playback with # 30000 CHP/TIM During PLAY Press keys in order 030000 TEST MODE: OFF Power POWER GGF1381 Test mode remote control unit XV-EV61...
(Refer to "6.3 ADJUSTMENT ITEMS AND LOCATION".) Spacer for Height adjustment Note: Turn a flat side Before removing the flexible cable for the into bottom pickup, soldering of the pickup circuit is necessary. For details, see "7.1.13 DISASSEMBLY". XV-EV61...
Page 109
(Example ERROR RATE: 6.6oe - 6 OK ) J : Min If error rate is OK, Disc playback normally. locks a root of • The measurement of block error rate tangential and radial adjustment screws with the Screw tight. Screw tight: GYL1001 Test mode end XV-EV61...
Perform only trace, video and audio outputs are nothing. = Screen display ON/OFF 1. Turn off the display by pressing the [AUDIO] (A8-1E) key of the remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the remote control unit. XV-EV61...
Page 111
• After the search, perform only trace and video and audio outputs are nothing. 4. Release the Search address input • Clear the address by pressing the [CLEAR] (A8-45) key. Release the address input mode when pressing the [CLEAR] key once again. XV-EV61...
Kinds of version / firmware of the FE. Scart terminal output [SK – ∗ ∗] RAM or ROM (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] XV-EV61...
• Region confirmation mode (ESC + AUDIO [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. XV-EV61...
(version of ST core software) softwareVersion . softwareRevision / buildNumber 0 F.E VERSION Version of FRONT END (version of mechanism controller CHIP software) MainVersion / Kinds of firmware RAM or ROM - Remote control code = Key code of Main unit XV-EV61...
PLL lost timeout 0x93 DECODER ERROR 0xa∗ DECODER TIMEOUT 0xb∗ Note : 0 x & & ID lost error 0xa3 ID lost timeout 0xb3 DEVICE ERROR 0xd∗ code SRAM error 0xd1 (Only this part is displayed to a display) XV-EV61...
Page 117
Do move to inner and outer periphery 1. Stepping motor of the stepping in the test mode? 2. Inside switch Stepping move timeout 0 x 54 Did timeout at stepping movement Do indicate "S-04" at the most inner 3. Driver periphery of the stepping? XV-EV61...
Page 118
SRAM error 0 x d1 Cannot access SRAM 2. Front End IC Is not bus line short-circuiting? 3. Front End-SRAM bus line FAILSAFE (0 x e∗) 1. software runaway Unexpected error 0 x e1 Unexpected error 3. Software bug XV-EV61...
(The SEARCH key is not accepted after all 9 digits have been entered.) Input ID Number ! [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Input ID Number ! XV-EV61...
Page 120
[Player's ID Number Setting] ID Number ? [ 0 0 0 0 0 0 0 0 1 ] Compare > 0 0 0 0 0 0 0 0 1 OK? <PLAY> Enter <STOP> Memory Clear Input ID Number ! XV-EV61...
Page 121
• Indication when the data have not been set If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. XV-EV61...
Pins 18 of the KEY input terminal is 5 V. If it is All operation keys are disabled. has already been pressed. not, check if the operation switch on the line is in failure. * Vdd= Approx. 5V (depending on the unit) ex.) 0.85Vdd= 0.85 × 5 (V) = 4.25 (V) XV-EV61...
(An opening screen is LOADING SW (LOAB S101) displayed on the monitor) • Is a LOAD-DRVC signal reaching ? BACK END IC (DVDM IC601) • Does the voltage of CN105 pin 1 change by pressing the Inside switch. Inside switch XV-EV61...
Page 124
Are there scratches or dirt on the disc ? Disc playback Is there a problem with the format of the disc? Disc (block noise, freeze, other) No sound (Picture is normal) Is signal output from DOUT signal (CN901-pin 21) on the DVDM Assy ? DVDM CN901-pin 21 XV-EV61...
Page 125
7.1.5 DSP TROUBLE SHOOTING (XV-EV61 Only) XV-EV61 Type Only • When a sound is not out in the surround mode with the digital signal input. • Suppose C,R parts to be poor contact and that is not damaged. • This shows failure analysis of DSP Assy.
Page 126
Pin 16 Do perform Step 4 5V→3V conversion Replace IC8701. for pin 4 ? IC8701 Pin 18 Pin 3 Do perform Do perform 5V→3V conversion Replace IC8701. 5V→3V conversion Replace IC8701. for pin 2 ? for pin 17 ? XV-EV61...
Page 128
Replace IC8401. Does a signal output Replace IC8501. Pin 25 Does a signal output Replace IC8401. Pin 26 Does a signal output Replace IC8401. Pin 27 Does a signal output Replace IC8401. Pin 28 Does a signal output Replace IC8401. XV-EV61...
• If no pulse is input to the AC terminal (Pin 4) for about 60 msec when the microcomputer is in Memory Backup mode, it will not do any processing. • The unit will recover from Memory Backup mode if a reset command is input to the XRESET terminal (Pin 8). XV-EV61...
Q3640 (E, C, and B)is turned on, and the level of XPROTECT becomes MID. → The microcomputer detects the XPROTECT level and shuts the power to the unit off. → After power off, unit recovers. (no reed to unit for 60 seconds) XV-EV61...
Page 131
Q106 is turned on, and the level of the XPROTECT line becomes D3658, Q3651 (E, C, B) is turned off, Q3651 (E2, B2, C2) is low. ← The microcomputer detects the XPROTECT level and shuts turned on, and the level of XPROTECT becomes low. the power to the unit off. XV-EV61...
Page 132
When the temperature at TH131 reaches 107-125_C (varying according to conditions,) the voltage at Point (A) becomes high enough to turn Q131 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-EV61...
Page 133
(2) When the VDET signal to the microcomputer is interrupted because of defective soldering of the 30-pin connector or incomplete insertion of FFC → The VDET level is lowered by the pull-down resistor (1 Mohms) on the side of the microcomputer. XV-EV61...
Page 134
Q3632 (E2, C2, B2), Q3633, and Q3636 (E, C, B) are turned on, the line to activate the SP relay becomes low level, and the SP Relay is turned off. (2) HP MUTE Q3635 is turned on, and the MUTE circuit for HP is turned on. XV-EV61...
Page 135
P R T E C T FL display V o l u m e FL display D V D E R R 5. Operations during Service Test mode • Basically, operations in Service Test mode are the same as in Normal mode. XV-EV61...
Page 137
Tray Panel was attached to it. Note : Operation check of the main unit is possible In this time, remove bottom part of the Front Panel even if removes the Deck Mechanism Section. first so that the Tray Panel is not caught. XV-EV61...
Page 138
For 6CH Only Troubleshooting AF/IF, For 3CH Only Replacc with Jig cable For troubieshooting of AF/IF, ( GGD1222 ) disconnect all FFC and connect to Line Input Turn the PCB with Rear Panel to as shown above XV-EV61...
Page 139
Remove of DVD Mecha Section Remove x4 screws. DVD Shield Remove Tunner Module Mecha Frame Jig cable ( XZD3001) DVD Mecha from Mecha Frame Remove of Power Module Section Remove (screws ×4). Remove the Module Holder R . Cut the cable binder XV-EV61...
Page 140
Mecha. Assy to the unit Bridge Tray Drive Cam Note when reinserting the Tray When reinserting the Tray, first align the triangle printed on the Loading Base and the pin of the Drive Cam, then insert the Tray. Front Side Loading Base Triangle XV-EV61...
Page 141
Dislodge the flexible cables from their packaged for the spindle motor Front Side placement Flexible cable Flexible cable for the pickup for the stepping motor Bottom View Remove the four hooks Traverse Mecha. Assy-S × 2 Remove the Traverse Mecha. Assy-S × 2 XV-EV61...
Page 142
Remove the flexible cable for the pickup Flexible cable for the pickup Bottom View Skew screw Skew screw Remove the two skew screws and two skew springs Remove the Pickup Assy Pickup Assy Skew spring Skew spring XV-EV61...
Page 143
Joint Spring Silicone Adhesive GEM1037 Joint 03 Silicone Adhesive GEM1037 Arrangement of the flexible cable Arrangement of the flexible cable for the spindle motor for the stepping motor : Conductive surface : Conductive surface Hook Hook Bottom View Bottom View XV-EV61...
Page 144
Reference line Hook Fold the flexible cable as indicated in the photo Fold the flexible cable along the hook Hook the part folded in Step 1 to the hook Reference Hook Pass the cable below the hook line Hook XV-EV61...
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC STM6316ATXXA, STM5589C, PDC108A 7 STM6316ATXXA (DVDM ASSY : IC301) • FRONT END IC ¶ Block Diagram XV-EV61...
Page 146
¶ Pin Function t i c t i c t s i t s i t s i t s i t s i t i s t i s XV-EV61...
Page 147
- t l l i c y t i - t l l i c y t i - t l l i c y t i d l l XV-EV61...
Selects the source you want to listen to c i t i t i DVD control buttons c i t i t i AUDIO Selects the audio channel or language s t i r i f : ' L XV-EV61...
Page 152
. r i r i f ' L ' ' L ' ' L ' t i r ' L ' ' L ' ' L ' ' L ' XV-EV61...
Page 155
RESET to DSP(MOTOROLA) Module DSPSS Slave selection to DSP(MOTOROLA) BUSY For MCACC DSPHREQ Error detection from DSP(MOTOROLA) DIRERR LOCK/UNLOCK from DIR Data input from DIR/CODEC DIRDD DIRCS Data output to DIR/CODEC DIRRST Reset to DIR /CODEC VSS4 VSS4 VDD4 VDD4 XV-EV61...
Page 156
Strobe for Key Control IC KCONCLK Clock for Key Control IC KCONDATA Data for Key Control IC INPUTSELB AUDIO source SELECT B INPUTSELA AUDIO source SELECT A(CD,TUNER,TAPE,AUX) BU4052 TCHALF Input switch of mecha half PB7/D7 TCMODE Input switch of mecha mode XV-EV61...
Page 157
• PortE and PortF can be selected for input or output by each 2 bits. • In case of without RDS, it is best that RDSDATA and RDSCLK are assigned as I/O port which can be set output and output low level. XV-EV61...
7.3 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 XV-EV61...
Selects audio channels for karaoke DOLBY NR (DEMO) Switches Dolby Noise Reduction on or off ASES Press for CD-to-tape synchro recording 10 TIMER/CLOCK ADJ. Use for setting the clock , as well as for setting and checking the timers XV-EV61...
Page 160
21 MIC input jacks 22 PHONES jack Headphone jack STANDBY/ON ( Switches the player on or into standby Function select buttons Selects the source you want to listen to DVD control buttons AUDIO Selects the audio channel or language XV-EV61...
Page 161
Selects a random play mode for Initial Settings, Play Mode functions, etc. TEST TONE (SHIFT+4) SYSTEM SETUP (SHIFT+HOME MENU) (EV61DVD model only) (EV61DVD model) Press to output the test tone for speaker Use to make various system and surround setup sound settings XV-EV61...
Page 162
Super VCDs, and WMA/MP3 discs, the Disc Navigator screen appears) TOP MENU (SHIFT+DVD MENU) Displays the top menu of a DVD disc 18 RETURN Press to return to a previous menu screen 19 TV CONTROL Switches the TV on or into standby XV-EV61...
Page 163
ADV. SURR. (EV61DVD model only) 17 2 DIGITAL Lights when one of the Advanced Surround Lights during playback of a Dolby Digital signal listening modes is selected 18 DTS (EV61DVD model only) Lights during playback of a DTS source XV-EV61...
Page 164
Lights when recording to the tape deck Lights when the Karaoke ECHO effect is selected Indicates the direction of tape playback Indicates the reverse mode: • – Single side playback • – Auto-reverse playback: stops after finishing playback in the ‘reverse’ (2 ) direction XV-EV61...