Vivitek DX6530 Series User Manual
  1. Manuals
  2. Brands
  3. Vivitek Manuals
  4. Projector
  5. DX6530 Series
  6. User manual
Vivitek DX6530 Series User Manual

Vivitek DX6530 Series User Manual

Dx6530/dw6030 series
Hide thumbs
Table of Contents

Advertisement

Quick Links

DX6530
DW6030
series
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DX6530 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Vivitek DX6530 Series

Summary of Contents for Vivitek DX6530 Series

  • Page 1 DX6530 DW6030 series User’s Manual...
  • Page 2 Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2013 Disclaimer The information in this document is subject to change without notice.
  • Page 3 — ’ Important Safety Information ® Congratulations on purchasing the Vivitek DLP projector! Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.
  • Page 4 — ’ — ’ — ’ Power Safety  Only use the supplied power cord.  Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic.  Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly.
  • Page 5 — ’ — ’ — ’ Projector Installation Notice  Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be in- stalled in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages.

  • Page 6: Table Of Contents

    — ’ — ’ — ’ Table of Contents INTRODUCTION................................. 1 ................................1 ACKING HECKLIST ............................... 2 IEWS OF ROJECTOR ARTS Front-right View ................................2 Bottom view ..................................3 ..................................4 EATURES OSD Controls and Status LEDs ............................4 ............................... 5 ERMINAL ANEL EATURES...
  • Page 7 — ’ — ’ — ’ Video Setting ................................. 39 Setup....................................40 Installation ..................................45 MAINTENANCE ................................51 ..............................51 LEANING THE PROJECTOR Cleaning the Cabinet ..............................51 Cleaning the Lens ................................. 51 Cleaning the Filters ..............................52 Replacing the Lamps ..............................54 APPENDIX ..................................

  • Page 8: D D L L P P P P R R O O J J E E C C T T O O R R - - D D X 3 / / D Dx

    – ’ – ’ – ’ NTRODUCTION Packing Checklist Carefully unpack the projector and check that the following items are included: PROJECTOR EMOTE CONTROL VGA C OWER CORD OWER CORD OWER CORD EGMENT ABLE MODEL HINA MODEL U MODEL OLOR HEEL CD-ROM ’...

  • Page 9: Views Of Projector Parts

    — ’ — ’ — ’ Views of Projector Parts Front-right View ABEL ESCRIPTION Lamp cover Remove cover to replace lamp or color wheel Lens Remove lens cap before use OSD control panel See OSD Controls and Status LEDs IR receiver Receiver for IR signal from remote control Lens Change button Press the Lens Change button before removing the lens...

  • Page 10: Bottom View

    – ’ – ’ – ’ Bottom view ABEL ESCRIPTION Contact your dealer for information on mounting the projector Ceiling support holes on a ceiling Note: When installing, ensure that you use only UL Listed ceiling mounts. Caution: With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 12 mm;...

  • Page 11: Top Features

    — ’ — ’ — ’ Top Features OSD Controls and Status LEDs MENU (10) (15) (11) ENTER CANCEL (16) (12) SOURCE AUTO (17) (18) (13) POWER WARNING LAMP1 LAMP2 (19) (14) DESCRIPTION ITEM LABEL ZOOM+ Increase/decrease projected image size ZOOM- UP CURSOR RIGHT CURSOR...

  • Page 12: Terminal Panel Features

    – ’ – ’ – ’ Terminal Panel Features ABEL ESCRIPTION Connect a LAN cable (not supplied) from a computer SERVICE For service personnel only. COMPUTER 3 IN Connect the DVI-D cable (not supplied) from a computer COMPUTER 1 IN Connect a VGA cable (supplied) from a computer MONITOR OUT Connect to a monitor...

  • Page 13: Remote Control

    — ’ — ’ — ’ Remote Control Item Label Description Status LED Lights when the remote control is used Turn the projector on at standby mode Turn the projector off (standby mode) ZOOM + Increase the projection image size ZOOM - Reduce the projection image size FOCUS+...

  • Page 14: Remote Control Operating Range

    – ’ – ’ – ’ Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level.

  • Page 15: Setup And Operation

    — ’ — ’ — ’ ETUP AND PERATION Inserting the Remote Control Batteries Remove the battery compartment cover by sliding the cover in the di- rection of the arrow. Insert the supplied batteries taking note of the polarity (+/-) as shown here.

  • Page 16: Installing Or Removing The Optional Lens

    – ’ – ’ – ’ Installing or Removing the Optional Lens Caution:  Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts.  When shipping the projector with the optional lens, remove the optional lens before shipping the projec- tor.

  • Page 17: Installing The New Lens

    — ’ — ’ — ’ Installing the New Lens Push the LENS RELEASE button and pull in the lens following the arrow mark on the lens slowly. Rotate the lens clockwise until it is with two clicks – 10 –...

  • Page 18: Throw Distance And Screen Size

    – ’ – ’ – ’ Throw Distance and Screen Size Example of DX6530 using Standard lens: The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 40 inches (1 m) measured diagonally when the projector is roughly 74.1 inches (1.88 m) from the wall or screen.
  • Page 19 — ’ — ’ — ’ Screen Size Semi-Long Zoom Long Zoom 1 2.28 - 3.82 3.67- 5.58 Diagonal Width Height Distance inches inches inches inches inches 1.02 0.81 0.61 71.9 - 121.3 1.83 3.08 115.9 - 176.8 2.94 4.49 1.27 1.02 0.76...

  • Page 20: Installing The Optional Color Wheel

    – ’ – ’ – ’ Installing the Optional Color Wheel The projector comes with a four-segment color wheel installed. An additional six-segment color wheel is optional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the follow- ing guide.
  • Page 21 — ’ — ’ — ’ Insert the six-segment color wheel Close the lamp cover and secure the retaining screws as shown. Storing Unused Color Wheel: Keep the unused color wheel in the zipper bag in which the 6-segment color wheel was packaged.

  • Page 22: Making Connections

    – ’ – ’ – ’ Making Connections Connecting Your PC or Macintosh Computer Enabling the computer’s external display: Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the ex- ternal display.

  • Page 23: Connecting An External Monitor

    — ’ — ’ — ’ Connecting an External Monitor Connect an external monitor to the projector through RGB out connections as shown below (see Terminal Panel Features on page 5). Note: When projector connects to the external monitor, please make sure Standby Mode is set to Standard . Monitor Out function works at Standard mode only.

  • Page 24: Connecting Your Dvd Player With Component Output

    – ’ – ’ – ’ Connecting Your DVD Player with Component Output To connect a DVD Player to the projector, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector. 2.

  • Page 25: Connecting Your Vcr Or Laser Disc Player

    — ’ — ’ — ’ Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Player, refer to the following diagram. Note: Refer to your VCR or disc player user’s manual for more information about the device’s requirements. Images may not be displayed correctly when using an S-Video or Video connection to fast-forward or fast- rewind scanning.

  • Page 26: Projecting An Image (Basic Operation)

    — ’ — ’ — ’ ROJECTING AN MAGE ASIC PERATION Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the projector is powered on correctly in order to avoid damage to components and un- necessary wear and tear.

  • Page 27: Selecting An Input Source

    — ’ — ’ — ’ Selecting an Input Source The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following guide to select the Input Source. Press INPUT on the control panel or on the re- mote control unit to display the INPUT Menu.

  • Page 28: Adjusting The Picture Position And Picture Size

    – ’ – ’ – ’ Adjusting the Picture Position and Picture Size The Picture Position and Picture Size can be adjusted manually from the lens control panel or from the remote control unit. Refer to the following guides to adjust Picture Position manually. Adjusting Picture Position Manually Press the Lens Shift keypad on the projector in any direction or...

  • Page 29: Lens Shift Adjustable Range

    — ’ — ’ — ’ Lens Shift Adjustable Range The adjustable range for lens shift is tabulated below and subject to the conditions listed. Note: The drawings below apply to the standard lens only. Normal projection position Desk-Front Projection Vertical Shift Height of projected image 0.1H...

  • Page 30: Optimizing An Rgb Image Automatically

    – ’ – ’ – ’ Optimizing an RGB Image Automatically Adjusting the Image Using Auto Sync To optimize an RGB image automatically refer to the following guide. Press the AUTO button on the remote control (see Remote Control on page 6) or the AUTO button on the control panel to optimize an RGB image automatically.

  • Page 31: Turning Off The Projector

    — ’ — ’ — ’ Turning off the Projector Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector. Note:  Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Do- ing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable.

  • Page 32: About Direct Power Off

    – ’ – ’ – ’ About Direct Power Off The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker. Note: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the pro- jector and starting to display an image.

  • Page 33: Convenient Features

    — ’ — ’ — ’ ONVENIENT EATURES Freezing a Picture The projected image can be frozen for short periods of time by using the remote control. This feature is useful for capturing still images from movies or freezing an animation at a particular point. To freeze the projected image, refer to the following guide.

  • Page 34: Changing Lamp Mode

    – ’ – ’ – ’ Changing Lamp Mode The projector has two lamp modes available, Normal and Eco. The Normal mode is used for every- day standard projection, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following guides.

  • Page 35: Correcting Keystone By Using The Remote Control

    — ’ — ’ — ’ Correcting Keystone by Using the Remote Control Important:  When adjusting the keystone, use Lens Shift to set the lens to center.  The adjustable vertical keystone range is Max. +/– 30° approx. The following are conditions under which the maximum angle is achieved: ...

  • Page 36: Preventing The Unauthorized Use Of The Projector

    – ’ – ’ – ’ Preventing the Unauthorized Use of the Projector The projector has a built-in security feature to lock the OSD control panels and deny remote control operation. The security feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword.

  • Page 37: Unlocking The Projector

    — ’ — ’ — ’ Unlocking the Projector To unlock the projector, refer to the following guide. When the projector is locked, either by re- quest during operation or at start up, the locked message is displayed. To unlock the projector, enter the previously defined PIN code to activate the projector.

  • Page 38: Using On-Screen Display

    — ’ — ’ — ’ SING CREEN ISPLAY Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD.

  • Page 39: Menu Tree

    — ’ — ’ — ’ Menu Tree Use the following illustrations to quickly find a setting or determine the range for a setting. Main Menu Submenu Picture Picture Mode Picture Mode Presentation Standard Game sRGB Brilliant Color Brightness Contrast Color Tint Sharpness...
  • Page 40 – ’ – ’ – ’ Main Menu Submenu Lamp Mode Normal/Eco Projection Mode Front / Rear / Ceiling+Front / Ceiling+Rear Fan Mode Normal / High / UP&Down Test Pattern None/RGB Ramps/Color Bars /Step Bars/Checkboard/Grid /Horizontal Lines/Vertical Lines/Diagonal Lines /Horizontal Ramp /Vertical Ramp/White Advance Setting Keystone...

  • Page 41: Input Menu Descriptions And Functions

    — ’ — ’ — ’ Input Menu Descriptions and Functions The Input menu displays all supported image sources. Select the required source from the menu using ▲ or ▼ and press to confirm. ABEL ESCRIPTION Select the source connected to the Computer 1 input Computer 1 (see Connecting Your PC or Macintosh Computer on page 15).

  • Page 42: Adjust Menu Descriptions And Functions

    – ’ – ’ – ’ Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as picture mode, bright- ness, color temperature…etc.. Picture Picture Mode Select a set of preset values using ◄ or ► from the list. Notice that the below values will change de- pending on the preset selection.
  • Page 43 — ’ — ’ — ’ Advance Setting Signal Type This function allows you to select the input signal from COMPUTER/COMPONENT1,2 or COMPONENT Auto Recognize the input signal as RGB or component automatically. Set When the input signal is RGB YCbCr Set when the input signal is Component(480I/480P/576I/576P).
  • Page 44 – ’ – ’ – ’ Color Manager This function allows you to adjust each of the six main colors comprised the color wheel by al- tering their Hue, Saturation or Value. Use ◄or► to adjust Hue of the main color as below Main Color Magenta Yellow...

  • Page 45: Signal Adjustment

    — ’ — ’ — ’ Note: Film Mode is available for below input and signals.  480I/576I/1080I from COMPUTER/COMPONENT 1, 2 or COMPONRNT INPUT  All signals from S-Video or Video input Noise Reduction This function provides high-quality images with minimal crawl and cross color noise, you can set your preferred level from Off to Level 3 to view a clear image.

  • Page 46: Video Setting

    – ’ – ’ – ’ Resolution This function provides the options to recognize the resolution of the input signal automatically. Recognize the input signal resolution automatically. Auto Set when the wide signal is received. Wide Set when the wide signal is received Auto Sync This function allows you to optimize the image automatically when the projector is turned on or when the input signal is switched or connected from a computer.

  • Page 47: Setup

    — ’ — ’ — ’ Video Setup Set the black level to 0 IRE or 7.5IRE. This function is available for 480I from COMPUTER/COMPONENT 1, 2 or COMPONENT input or NTSC3.58 from Video or S-Video input. Closed Caption Set to CC1 or Off as required. Note: This function is available in following case ...
  • Page 48 – ’ – ’ – ’ Standby Mode Standby Mode allows you to put the projector in the standby condition to consume less power, two standby modes are selectable as below. Standard: Monitor out, LAN/RS232C and Network functions are activated in standby mode : Monitor out, LAN/RS232C and Network functions are switched in standby mode Note: The HTTP server functions, MONITOR OUT and RS232C Control are not available when Standby...
  • Page 49 Password must be recorded in a safe place where only authorized users have access.  If you lose or forget the password, please contact Vivitek Authorized Dealer or Service Center Keypad Lock To prevent unauthorized operation by projector control panel, use this function to lock the buttons on the projector.
  • Page 50 – ’ – ’ – ’ Note:  Keypad Lock cannot be released if the project is under below status - Menu is displayed - Projector is at standby mode - The projector is during warming up - Input signal is changing or Auto Sync function is operation. - Freeze function is operated.
  • Page 51 — ’ — ’ — ’ Note:  The image can be captured only when the input source is non-interlace signal from COMPUTER/COMPONET 1,2 or DVI-D inout, the image from Video or S-Video cannot be catured.  The captured image must be native resolution such 1280x800 for WXGA, 1024x768 for XGA ...

  • Page 52: Installation

    – ’ – ’ – ’ Installation The Installation tab contains menu options for various setup conditions such as orientation and re- mote sensor mode and is accessed through the Setting menu. The following table lists all functions with a brief description. Language Select the OSD language to be used, eight languages Lamp Control...
  • Page 53 — ’ — ’ — ’ Lamp Mode Select Normal or Eco from the lamp mode window. The lamp life can be extended by using the Eco mode and the fan noise can be reduced. Projection Mode Projection Mode enables you to set how the projected image is displayed. Select from the following: Standard forward facing projection (Default setting) Front Standard rear projection.
  • Page 54 – ’ – ’ – ’ Advance Setting Keystone When the image is projected either from the top or from the bottom toward the screen at an angle, the image becomes distorted, use Keystone function to correct the distortion, the adjustable range is ap- proximately＋30 degree.
  • Page 55 — ’ — ’ — ’ Network The Network menu contains the general LAN settings Link Display the network connection status DHCP Client Select either a static IP (Off) or DHCP IP (On) setting by using ◄ or ►, On: Enable configuration parameters for IP Address, Subnet Mask, Gateway and DNS automatically.
  • Page 56 – ’ – ’ – ’ Apply Apply and save settings, please select Yes to apply the settings. Note:  Avoid setting an IP address that duplicates the IP Address of other network equipment.  For details about network setting, consult your network administrator. Communication Speed Select communication speed to set the baud rate of the connection.
  • Page 57 — ’ — ’ — ’ Filter Timer Reset The function allows you to reset the filter timer, please make sure to reset the timer after cleaning or change the dust filter. Press Enter or ► to display the confirmation message and select Yes to reset the filter timer.

  • Page 58: Maintenance

    – ’ – ’ – ’ AINTENANCE Cleaning the projector Cleaning the Cabinet Refer to the following guide to clean the projector cabinet. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent and wipe the cabinet. 3.

  • Page 59: Cleaning The Filters

    — ’ — ’ — ’ Cleaning the Filters The projector uses three filters to keep the fans free of dust and other particles, and should be cleaned every 500 hours of operation. In dusty environments, it is recommended to clean the filters more frequently.
  • Page 60 – ’ – ’ – ’ Lift the filter foams from all three filteholders in the direction shown. Remove them completely from each filterholder and discard. Place a replacement foam and press down firmly Replace the filter holders by push- ing gentlyin the direction shown.

  • Page 61: Replacing The Lamps

    — ’ — ’ — ’ Replacing the Lamps The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement part, contact your local dealer if unsure. Note:  Lamps are positioned differently. Take care not to force the lamps when replacing. ...
  • Page 62 – ’ – ’ – ’ Remove the four screws on the lamp cover (A), and lift the lamp cover as shown (B). Loosen the two captive screws on the lamp module (A). Lift the module handle up as shown (B). Pull firmly on the module handle in the direction shown to remove the lamp.

  • Page 63: Appendix

    — ’ — ’ — ’ PPENDIX Troubleshooting Indicator Messages Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the projector through the WARNING LED.

  • Page 64: Common Problems And Solutions

    – ’ – ’ – ’ Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often the problem is something as simple as a loose connection. Check the following before proceed- ing to the problem-specific solutions.

  • Page 65: Image Problems

    — ’ — ’ — ’ Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1.

  • Page 66: Remote Control Problems

    – ’ – ’ – ’ Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on the projector. 2. Ensure the path between remote and sensor is not obstructed. 3.

  • Page 67: Specifications

    — ’ — ’ — ’ PECIFICATIONS Projector Specifications Model DX6530/DX6535 DW6030/DW6035 Display Devices 0.7”,1- DLP Chip 0.65”,1-DLP Chip Resolution XGA(1024x768) WXGA(1280x800) Optional Lens F number F 1.64 ~1.86 ( Standard Lens) Zoom Power, 1.3X,(f=26.0-34.0mm) Focus Power Lens Shift Power(V:+50% / H:±10% Projection Lamp 280W x 2 lamps Input Terminals...

  • Page 68: Lens Options

    – ’ – ’ – ’ Lens options The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. to the sales dealer. Part number Projection Lens F Number Focus Length Throw Ratio (mm) DX6530/35 DW6030/35...

  • Page 69: Pin Assignments Of Mini D-Sub 15 Pin Input Connector

    — ’ — ’ — ’ Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: 0.7Vp-p (Analog) Sync signal: TTL level RGB S UMBER IGNAL NALOG IGNAL Green or Sync on Green Blue Ground Ground Red Ground Cr Ground Green Ground Y Ground...

  • Page 70: Compatible Input Signal List

    – ’ – ’ – ’ Compatible Input Signal List The following table shows compatible signal types, their resolution and frequency refresh rates. Horizontal: 15kHz, 31kHz to 90 kHz, Vertical: 50 Hz to 85 Hz Mode Resolution H-Sync (KHz) V-Sync (Hz) Analog Digital 31.5...
  • Page 71 — ’ — ’ — ’ Signal Analog Digital Vertical Frequency(Hz) Horizontal Frequency(Hz) 480i 15.7 60.0 SDTV 576i 15.6 50.0 480p 31.5 60.0 EDTV 576p 31.3 50.0 720p 45.0 60.0 720p 37.5 50.0 1080i 33.8 60.0 HDTV 1080i 28.1 50.0 1080p 56.3 1080p...

  • Page 72: Rs232 Control Commands And Cable Connections

    – ’ – ’ – ’ RS232 Control Commands and Cable Connections This projector provides a function to control and monitor the projector's operations by using the RS- 232C serial port. Cable Connection Connector (DIN-9P) RS232C Connection Pin 1, 4, 6 and 9 are not used. Note: ...

  • Page 73: Control Command

    — ’ — ’ — ’ Control Command There are two types of the command, Get commands and Set Command, the command is structured by the Header code, command code, data code and end code. All of commands contain ASCII test string ending with an ASCII carriage return character.
  • Page 74 – ’ – ’ – ’ Command Group 01 Operation ASCII Description Return String Get Brightness setting N=-30~30 Pn/F V99G0101 56H 39H 39H 47H 30H 31H 30H 31H 0DH Set the Brightness N=-30~30 V99S0101n 56H 39H 39H 53H 30H 31H 30H 31H n 0DH Get contrast setting N=-30~30 Pn/F...
  • Page 75 — ’ — ’ — ’ Command Group 03 Operation ASCII Description Return String Get Aspect Ratio setting Pn/F V99G0301 56H 39H 39H 47H 30H 33H 30H 31H 0DH 0: Normal 1: Full 2: 4:3 3 :16:9 4 :Native Set Aspect Ratio V99S0301n 56H 39H 39H 53H 30H 33H 30H 31H n 0DH 0: Normal 1: Full...
  • Page 76 – ’ – ’ – ’ Command Group 04( Remote Control Buttons) Operation ASCII Description Return String V99S0401 56H 39H 39H 53H 30H 34H 30H 31H 0DH V99S0402 56H 39H 39H 53H 30H 34H 30H 32H 0DH V99S0403 56H 39H 39H 53H 30H 34H 30H 33H 0DH FOCUS+ V99S0404 56H 39H 39H 53H 30H 34H 30H 34H 0DH...

  • Page 77: Screen Trigger

    — ’ — ’ — ’ Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up.

  • Page 78: Operation Using Http Browser

    – ’ – ’ – ’ Operation Using HTTP Browser Overview The use of HTTP server functions will allow control of the projector from a web browser without the installation of special software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser.

  • Page 79: Configuring Network Settings

    — ’ — ’ — ’ Configuring Network Settings The Network Settings screen is displayed as follows: http:// <the projector's IP address> /lanconf.html DOMAIN Host Name: Type in a host name, up to 60 alphanumeric characters can be used. Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used.
  • Page 80 – ’ – ’ – ’ TEST MAIL Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature. Test Mail Status Button: Click to display the test result. Sample of a message sent from the projector: Projector Name: X X X X Lamp 1 or 2 Hours Used: xxxx [H] The lamp is at the end of its usable life.

  • Page 81: Structure Of The Http Server

    — ’ — ’ — ’ Structure of the HTTP Server Once the projector is connected to a network and configured correctly, the following screen is dis- played through the web browser. http:// <the projector's IP address> /index.html UNCTION ETTING ESCRIPTION POWER This controls the power to the...
  • Page 82 – ’ – ’ – ’ UNCTION ETTING ESCRIPTION STATUS Refresh – Updates the panel with the latest information This displays the status of se- lected projector functions Lamp1 life – Displays the remaining life of Lamp 1 as a percentage Lamp2 life –...

  • Page 83: Regulatory Compliance

    — ’ — ’ — ’ EGULATORY OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This manual is also suitable for:

Dw6030Dx6535Dw6035

Table of Contents