Page 1
Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
The for information and other details concerning warranty. prices charged by Wells Bloomfield for its products are SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS Resetting of safety thermostats, circuit breakers, over cleaning schedules, are customer responsibility.
PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
FEATURES & OPERATING CONTROLS A. INFINITE SWITCH 1. On INFINITE SWITCH CONTROLLED warmers, power is applied to the heating element based on the control knob position, which varies the duty cycle of the heating element. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB.
Damage Do not operate this appliance if the control panel is damaged. Call to the appliance may result if your Authorized Wells Service Agent for service. these instructions are not followed. The technical content of this manual, including any wiring diagrams, schematics, parts breakdown illustrations and/or adjustment procedures, is intended for use by qualified technical personnel.
INSTALLATION UNPACKING & INSPECTION NOTE: DO NOT discard the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
Page 7
INSTALLATION For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c.
CAUTION: between the change in wet or dry operation. SHOCK HAZARD c. Wells Manufacturing recommends operating WET for consistent food heating. DO NOT splash or pour water d. If your wet-operation warmer is allowed to run dry, turn it onto control panel or wiring.
Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean stainless steel. Warmer pans, insets and other vessels are subject to a harsher environment. Wells Manufacturing uses an very high quality stainless steel (#304DDQ) for our food warmer pans.
Contact your Authorized Wells Service Agency to inspect warmer if water or grease contamination is suspected. 6. Close drain valve. Add proper amount of warm water. Turn control...
Page 11
CLEANING INSTRUCTIONS WEEKLY CLEANING INSTRUCTIONS CAUTION: CHEMICAL BURN PREPARATIONS: Remove any insets, pans and/or adapter tops. HAZARD Drain or remove water from well if used for wet operation. Deilimng chemicals may be caustic. Wear appropriate FREQUENCY: Weekly, or whenever lime or scale is seen personal protective equipment.
Drain valve damaged or pan(s) Contact your Authorized Wells leaking Service Agency for repairs There are no user-serviceable components in this appliance. In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs. WIRING DIAGRAM...
PARTS & SERVICE DESCRIPTION PART NO. Always use an inset. DO NOT place food directly ADAPTERS & INSETS into the warmer pan. ADAPTER TOP, convert 12” x 20” warmer to hold two 7 qt. insets 21502 ADAPTER TOP, convert 12” x 20” warmer to hold two 4 qt.
12” x 20” warmers only, adapt to wood counter authorized replacement parts, up to 1¾” thick 22593* contact your Wells authorized service agency, or call: Wellslok Extension Kits for UL Listed units approved for installation in wood counter tops Wells Bloomfield, LLC One well units require one kit / Two and three well units require 10 Sunnen Dr., P.O.Box 430129...
Page 16
Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING - QUALITY SERVICE SERVICE TRAINING - QUALITY SERVICE Genuine Parts Protect - YOU - All - Ways CUSTOMER SATISFACTION CUSTOMER SATISFACTION WELLS BLOOMFIELD, LLC 10 Sunnen Drive P.O.Box 430195...