Hoover TurboPOWER WindTunnel S3646 Owner's Manual

Hoover TurboPOWER WindTunnel S3646 Owner's Manual

Canister cleaner with powered nozzle
Hide thumbs Also See for TurboPOWER WindTunnel S3646:

Advertisement

Quick Links

Hoover
TurboPOWER WindTunnel
Canister Cleaner
with Powered Nozzle
®
S3646
www.hoover.com
®
TM
Review this manual before
operating cleaner.
Owner's Manual
English ‹ pp. 1-11
Español ‹ pàg.12-17
TM
Français ‹ p.18-23

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TurboPOWER WindTunnel S3646 and is the answer not in the manual?

Questions and answers

Summary of Contents for Hoover TurboPOWER WindTunnel S3646

  • Page 1 Hoover Owner’s Manual English ‹ pp. 1-11 ® TurboPOWER WindTunnel Español ‹ pàg.12-17 Français ‹ p.18-23 Canister Cleaner with Powered Nozzle ® S3646 Review this manual before operating cleaner. www.hoover.com...
  • Page 2: Table Of Contents

    Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner’s manual. Verification of date of purchase may be required for warranty service of your Hoover product. Important Safeguards! Index Assembling Cleaner...
  • Page 3: Assembling Cleaner

    If you should happen to need assistance during assembly Unpack cleaner from carton and iden- or operation, tify the parts shown. Remove and Visit us online at www.hoover.com to find the service outlet nearest you dispose of cardboard packing. A. Canister cleaner B. WindTunnel™ powered nozzle C.
  • Page 4: Cleaner Description

    Attach nozzle and wands into opening near end of wand. Be sure bottom cord clip. nozzle is locked in place. Note: For some models, bottom cord The wand with the storage clip connects To release, press down on center of clip is on wand storage clip.
  • Page 5: Polarized Plug

    Push the hand grip (G) down onto wand so that the button projection (H) fits into the slot. Push the latch to the lock symbol to secure wand. Push plug on power nozzle cord com- pletely into receptacle underneath hand grip. Always disconnect cleaner from electrical outlet before attaching or removing power nozzle plug.
  • Page 6: Variable Speed Control

    Variable speed control Edge cleaning Hard surface floor cleaning (some models) The power nozzle can be used for Special edge groomers are provided on cleaning hard surface floors such as The variable speed control (F) is located both sides of the nozzle to remove dirt in wood, linoleum, vinyl, asphalt and on the hand grip.
  • Page 7: To Clean Stairs

    Leading Retailers, Hoover Factory positioned down as shown. Low suction or pick up may be due to Service Centers, or through The Hoover Lift up on wand to remove storage clip a blockage in the system. Refer to the Company online at www.hoover.com.
  • Page 8: Cleaning Filters

    Use screws. only a genuine HOOVER Belt part no. Note: Do not remove the 3 screws in the triangle formation as these hold 40201180 when a belt replacement is the motor in place.
  • Page 9 3-10 3-11 Return nozzle to original position and lift Remove brush roll cover (C) by removing Lift off brush roll cover (C). off hood. the 3 Phillips head screws. 3-12 3-13 3-14 If belt is not broken but is stretched or Lift up end of agitator brush roll.
  • Page 10: Lubrication

    When the blockage is not removed, turned on. Use only HOOVER part no. the thermal protector will trip and When agitator brush roll brushes are 27317-307, which is a fused bulb, when cleaner will stop running.
  • Page 11: If You Have A Problem

    •Increase power setting/close suction Push nozzle connector down to lowest delivery, or house calls; however, if you regulator. mail your appliance to a Hoover Factory •Hose not properly connected to position. Look into nozzle connector Service Center for warranty service, cleaner and remove any blockage.

Table of Contents