US Electronics UY322-EPG User Manual

before you begin
If you have a TV with a remote control, we
User's Guide for the
recommend that you plug its power cord
directly into a wall outlet if available (your
UY322-EPG
cable installer may select an alternate setup).
Make sure to set your TV to channel 2, 3, or 4
3-in-1 Remote Control
as directed by your cable company.
featuring Memory Lock
™
and Predictive Technology ™
Memory Lock
I
N that saves the device codes that are
w w w . u s e l e c t r o n i c s . c o m
F programmed into the remote, even when
O the batteries are removed.

installing batteries

Before you can program or operate the remote
control, you must install two AAA Alkaline
batteries.
Remove the battery compartment cover on the
Check battery polarity carefully,and
install the batteries as shown in the
Replace the battery compartment cover.
© 1998 US Electronics Components Corp. All rights reserved
Part Number USE17370, Version 1.1
9804
function keys
See the chart below for a description
is an exclusive technology
™
Step 1
back of your remote control.
Step 2:
illustration below.
Step 3:
The chart below shows the functions of special keys for your cable box and program guide.
*
Install two
AAA alkaline batteries #
as shown here
MUSIC/ENTER switches between cable TV and Music Choice™
LAST
FAV
MUTE
P
PPV
EXIT
INFO
MENU
GUIDE
SEL
CURSOR KEYS navigate through on-screen guides (see the highlighted section above)
PAGE +/-
DAY +/-
EPG RECORD initiates VCR recording through the on-screen menu (if so equipped)
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
button functions
numeric keypad
cable box
These keys allow you to enter the channel
you want to view.You will also use them
to setup the remote
of the key functions
vcr controls
These keys operate standard VCR functions.
Operating Note: Press the [RECORD] button
twice to start recording on your VCR.
Cursor Keys
N
Depending on the configuration
O of your cable box, certain
MORE
T functions listed below may or
INFO
may not be functional.
E
See the cable box manual for further details.
displays help for on-screen display screens
future use
recalls the last channel that was viewed
cycles through your favorite channels
turns volume off
displays the quick function screen
future use
displays pay-per-view options
exits the on-screen display menus
displays channel and program information
displays the main on-screen display menu
displays the program guide
selects various options and tunes programs from the program guide
pages through on-screen menu and program guide screens
moves the program guide one day forward and backward

setting up your remote control

Follow these simple steps to program your remote for your VCR,TV,and cable box.

Before you start

Locate the [SETUP] button, which is at the very bottom of the
remote (see illustration at right).
Manually turn on your VCR,TV, and cable box.
After you find the correct code for each device, write the code on the supplied sticker.
step
Press the [VCR POWER] button,then the [SETUP] button on the remote.
1
Enter the 3-digit VCR code for your brand of VCR listed in the "VCR codes" chart on the
other side of this manual by pressing the appropriate buttons on the numeric key pad.
Press the [SETUP] button again to save the code. The red indicator light at the upper
for right-hand corner of your remote will flash 3 times if these steps were followed correctly.
your
Press the [VCR POWER] button again to test the code you've entered. The VCR
VCR
should turn ON or OFF each time the [VCR POWER] button is pressed. If the VCR
doesn't turn ON and OFF, repeat this VCR setup procedure with the next code listed in
the "VCR codes"chart.
step
Press the [TV POWER] button,then the [SETUP] button on the remote.
2
Enter the 3-digit TV code for your brand of TV listed in the "TV codes"chart.
Press the [SETUP] button again to save the code. The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
for
Press the [TV POWER] button again to test the code you've entered. The TV should
your
turn ON or OFF each time the [TV POWER] button is pressed. If the TV doesn't turn
TV ON and OFF, repeat this TV setup procedure with the next code listed in the "TV
codes" chart.
step
Press the [CABLE POWER] button,then the [SETUP] button on the remote.
3
Enter the 3-digit cable box code listed below.
Press the [SETUP] button again to save the code. The red indicator light at the upper
right-hand corner of your remote will flash 3 times if these steps were followed correctly.
for
your
Press the [CABLE POWER] button again to test the code you've entered. The cable box
cable
should turn ON or OFF each time the [CABLE POWER] button is pressed.If the cable box
doesn't turn ON and OFF,try entering the code again.
box
The setup code for the
Following the above steps allows the remote to control
N
GI/Jerrold™ CFT2200™ series
volume through your cable box.If you would like volume
Helpful
O
cable box is
to be controlled through your TV,perform step 3 before
T
Hint 002
step 2.If you have a combination TV/VCR,volume will be
E
controlled only through the cable box.
Jerrold™ is a trademark of GIC corp.
VCR CONTROLS
STOP RECORD PLAY
REW PAUSE FWD
SETUP