US Electronics UG3DIGI User Manual

1
If you have a TV with a remote control,
User's Guide for the
we recommend that you plug its power
UG3DIGI cord directly into a wall outlet if avail-
able (your cable installer may select an
alternate setup).
3-in-1 Cable TV
Make sure to set your TV to channel 2, 3,
RemoteControl
or 4 as directed by your cable company.
VISIT US ON THE WEB
Memory Lock
I
You can find programming instructions and codes
N technology that saves the device codes
for all of our remote controls, as well as information
F that are programmed into the remote,
about our other products on our website:
O even when the batteries are removed.
www.uselectronics.com
2
Before you can program or operate the
remote control, you must install two AA
Alkaline batteries.
Step 1:
Remove the battery compartment cover
on the back of your remote control. A
screwdriver may be required to pry the
cover off.
Step 2:
Check battery polarity carefully, and
install the batteries as shown in the
illustration below
Step 3:
Replace the battery compartment cover.
!
© 1999 US Electronics Components Corp.
All rights reserved
Part Number USE17837, version 1.0
9903
BEFORE YOU 3 KNOW YOUR
BEGIN REMOTE
CABLE BOX
FUNCTION KEYS
See the chart below for a
description of the key
functions. Note the location
of the [SETUP] key — you
will use it when you setup
™ is an exclusive
INSTALL
BATTERIES
The chart below shows the functions of special keys for your cable box and
program guide. See the cable box manual for further details.
FAV
LOCK
SETUP
TV/VCR
MUTE
MENU
GUIDE
SEL
CURSOR KEYS
INFO
IMPORTANT
EXIT
NOTE
PAGE +/-
DAY +/-
Weak batteries may disrupt
LAST
normal operation of the remote.
MUSIC/ENTER
A, B, C
We recommend that you use
HELP
only AA alkaline batteries.
VCR/VOD
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.
NUMERIC KEYS
These keys allow you to enter
the channel you want to view.
You will also use them
to setup the remote
the remote.
VCR CONTROLS
These keys operate standard
VCR or VOD functions
depending on the position of
the VCR/VOD switch. Note:
Press the [REC] key twice to
CURSOR KEYS
start recording on your VCR.
MORE
INFO
cycles through your favorite channels
used for Parental Control
used to setup the remote
configuration of your
switches the VCR between TV and VCR mode
cable box, certain
turns volume off
functions listed here may
displays the main on-screen display menu or may not be functional.
displays the program guide
selects various options and tunes programs from the program guide
navigate through on-screen guides
displays channel and program information
exits the on-screen display menus
pages through on-screen menu and program guide screens
moves the program guide one day forward and backward
recalls the last channel that was viewed
switches between cable TV and Music Choice™
future use
displays help for the on-screen display
switches the VCR controls into Video-on-Demand controls
4 SETTING UP
YOUR REMOTE
Following these steps allows the remote to control volume through your cable box. If
you would like volume to be controlled through your TV, perform step C before step B.
If you have a combination TV/VCR, use a code from the VCR Codes section (volume will
be controlled only through the cable box).
A
FOR YOUR VCR
b
Press the [VCR] button, then the [SETUP] button on the remote.
c
Enter the 3-digit VCR code for your brand of VCR listed in the "VCR
codes" chart on the other side of this manual by pressing the
appropriate buttons on the numeric key pad.
d
Press the [SETUP] button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
e
Press the [VCR] button again to test the code you've entered. The
VCR should turn on or OFF each time the [VCR] button is pressed. If
the VCR doesn't turn on and OFF, repeat this VCR setup procedure
with the next code listed in the "VCR codes" chart (section 5) .
B
FOR YOUR TELEVISION
b
Press the [TV] button, then the [SETUP] button on the remote.
c
Enter the 3-digit TV code for your brand of TV listed in the "TV codes"
chart.
d
Press the [SETUP] button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
e
Press the [TV] button again to test the code you've entered. The TV
should turn on or off each time the [TV] button is pressed. If the TV
NOTE
doesn't turn on and off, repeat this TV setup procedure with the next
Depending on the
code listed in the "TV codes" chart (section 6).
C
FOR YOUR CABLE BOX
b
Press the [CABLE] button, then the [SETUP] button on the remote.
c
Enter the 3-digit cable box code: [0] [0] [0].
d
Press the [SETUP] button again to save the code. The red indicator
light at the upper left-hand corner of your remote will flash 3 times if
these steps were followed correctly.
Press the [CABLE] button again to test the code you've entered. The
e
cable box should turn on or off each time the [CABLE] button is pressed.
If the cable box doesn't turn on and off, try entering the code again.