US Electronics UY4DIGI User Manual

before you begin

User's Guide If you have a TV with a remote control, we
recommend that you plug its power cord
for the
directly into a wall outlet if available (your
cable installer may select an alternate setup).
UY4DIGI
Make sure to set your TV to channel 2, 3, or 4
UY4DIGI-P
as directed by your cable company.
UY4DIGI-S
I Memory Lock
N that saves the device codes that are
4-in-1 Remote Control
F programmed into the remote, even when
featuring Memory Lock ™
O the batteries are removed.
w w w . u s e l e c t r o n i c s . c o m

installing batteries

Before you can program or operate the remote
control, you must install two AAA Alkaline
batteries.
Remove the battery compartment cover on the
back of your remote control.
Check battery polarity carefully,and
install the batteries as shown in the
Replace the battery compartment cover.
© 1998 US Electronics Components Corp. All rights reserved
Part Number USE17363, Version 1.1
9804
cable box
function keys
See the chart below for a description
of the key functions.
™ is an exclusive technology
Step 1
Step 2:
Cursor Keys
MORE
illustration below.
Step 3:
The chart below shows the functions of special keys for your cable box and program guide.
Install two * (HELP) displays help for the on-screen display
AAA alkaline batteries
# (FAV) cycles through your favorite channels
as shown here
A/THEME future use
LAST recalls the last channel that was viewed
MUSIC/ENTER switches between cable TV and Music Choice™
MUTE turns volume off
B/LIST future use
EXIT exits the on-screen display menus
PPV displays pay-per-view options
SWITCH switches between cable inputs on a dual-cable system
C/CANCEL future use
INFO displays channel and program information
MENU displays the main on-screen display menu
GUIDE displays the program guide
SEL selects various options and tunes programs from the program guide
CURSOR KEYS navigate through on-screen guides (see the highlighted section above)
PAGE +/- pages through on-screen menu and program guide screens
DAY +/- moves the program guide one day forward and backward
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.

button functions

device/number keys
• Device keys select what device the buttons
on the remote will operate.
• Number keys allow you to enter the
channel you want to view.You will also use
them to setup the remote.
vcr controls
These keys operate standard VCR functions.
Operating Note: Press the [RECORD] button
(or the [EPG RECORD] button) twice to start
recording on your VCR.
INFO
See the cable box manual for further details.
NOTE
Depending on
the configuration of
your cable box, certain
functions listed here
may or may not
be functional.

setting up your remote control

Before you get started, find the red buttons labelled [VCR], [TV], and [CABLE] at the top of the remote
control. In this section we'll refer to each of these buttons as a [DEVICE] buttons. Each time you see
[DEVICE] button in the in this section, press the appropriate button for the device that will be operated
by the remote (TV, VCR, Cable Box, etc.). Next, find the [SETUP] button at the bottom of the remote
control. Once you are familiar with the location of the buttons,continue below.
1.
for your VCR, TV, and cable box
Press the [DEVICE] button,then the [SETUP] button on the remote.
Enter the 3-digit device code for your brand of device listed in the charts on the other side of this
manual by pressing the appropriate buttons on the numeric key pad.
Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner
of your remote will flash 3 times if these steps were followed correctly.
Press the [POWER] button to test the code you've entered. The device should turn ON or OFF each
time the [POWER] button is pressed. If the device doesn't turn ON and OFF, repeat this setup
procedure with the next code listed for the device.
2.
for a digital music terminal (optional)
Press the [AUX] button,then the [SETUP] button on the remote.
Enter the 3-digit device code for your type of digital music terminal by pressing the appropriate buttons
on the numeric key pad.
Jerrold DCR1000 .............................000
Scientific-Atlanta DMX ..................002
Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner
of your remote will flash 3 times if these steps were followed correctly.
Press the [AUX] button again to test the code you've entered.The device should turn ON or OFF each
time the [POWER] button is pressed. If the device doesn't turn ON and OFF, repeat this setup
procedure with the next code listed for the device.
3.
for an auxilliary device (optional)
The red [AUX] button allows you to control a or a second TV or VCR if you aren't using it for a digital
music terminal. To do this, you need to setup the [AUX] button so it functions like a second [TV] or
[VCR] button.
Press the [SETUP] button,then the [MENU] button on the remote.
Now, press the [AUX] button, and then the button that you want the [AUX] button to emulate (either
the [TV] or [VCR] button), then press the [SETUP] button. The red indicator light at the upper right-
hand corner of your remote will flash 3 times if these steps were followed correctly.
The [AUX] button can now be programmed to control the specific device. Follow the instructions above
in step 1 and press the [AUX] button any time you are told to press the [DEVICE] button.
The setup code for Jerrold /GI/Motorola
Helpful
DCT digital converters and CFT2200 : series cable boxes is
™
Hint
002