US Electronics UY420 User Manual

before you begin

If you have a TV with a remote control, we
User's Guide
recommend that you plug its power cord
for the
directly into a wall outlet if available (your
cable installer may select an alternate setup).
UY420
Make sure to set your TV to channel 2, 3, or 4
as directed by your cable company.
4-in-1 Remote Control
I Memory Lock
featuring Memory Lock ™
that saves the device codes that are
N
F programmed into the remote, even when
O the batteries are removed.
w w w . u s e l e c t r o n i c s . c o m

installing batteries

Before you can program or operate the remote
control, you must install two AAA Alkaline
batteries.
Remove the battery compartment cover on the
Check battery polarity carefully,and
install the batteries as shown in the
Replace the battery compartment cover.
© 1998 US Electronics Components Corp. All rights reserved
Part Number USE17393, Version 1.2
9808
function keys
See the chart below for a description
™ is an exclusive technology
Step 1
back of your remote control.
Step 2:
illustration below.
Step 3:
The chart below shows the functions of special keys for your cable box and program guide.
Install two
AAA alkaline batteries T/V ENTER
as shown here
DELETE
PROG
SELECT
ENTER
DISPLAY
F
LAST CH
FAV
A/B
MENU
MUTE
PAGE +/-
CURSOR +/-
US Electronics provides these function descriptions as a general guide to allow you to become more familiar with your cable box. Refer to your cable box manual for descriptions of specific functions.

button functions

device/number keys
cable box
• Device keys select what device the buttons
on the remote will operate.
• Number keys allow you to enter the
of the key functions.
channel you want to view.You will also use
them to setup the remote.
vcr controls
These keys operate standard VCR functions.
Operating Note: Press the [RECORD] button
twice to start recording on your VCR.
Cursor Keys
MORE
INFO
See the cable box manual for further details.
finalizes channel selection on some TVs and VCRs
deletes a channel from your list of favorite channels
adds a channel to your list of favorite channels
selects various options from on-screen menus
enters command functions
displays the current time, channel, and date
brings up the quick functions screen
recalls the last channel that was viewed
cycles through your favorite channels
switches between cable inputs in a dual-cable system
displays the main on-screen display menu
turns volume off
pages through on-screen menu
moves the cursor up and down

setting up your remote control

Before you get started, find the red buttons labelled [VCR], [TV], and [CABLE] at the top of the remote
control. In this section we'll refer to each of these buttons as a [DEVICE] buttons. Each time you see
[DEVICE] button in the in this section, press the appropriate button for the device that will be operated
by the remote (TV, VCR, Cable Box, etc.). Next, find the [SETUP] button at the bottom of the remote
control. Once you are familiar with the location of the buttons,continue below.
1.
for your VCR, TV, and cable box
Press the [DEVICE] button,then the [SETUP] button on the remote.
Enter the 3-digit device code for your brand of device listed in the charts on the other side of this
manual by pressing the appropriate buttons on the numeric key pad.
Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner
of your remote will flash 3 times if these steps were followed correctly.
Press the [POWER] button to test the code you've entered. The device should turn ON or OFF each
time the [POWER] button is pressed. If the device doesn't turn ON and OFF, repeat this setup
procedure with the next code listed for the device.
2.
for a digital music terminal (optional)
Press the [AUX] button,then the [SETUP] button on the remote.
Enter the 3-digit device code for your type of digital music terminal by pressing the appropriate buttons
on the numeric key pad.
Jerrold DCR1000 .............................000
Scientific-Atlanta DMX ..................002
Press the [SETUP] button again to save the code.The red indicator light at the upper right-hand corner
of your remote will flash 3 times if these steps were followed correctly.
Press the [AUX] button again to test the code you've entered.The device should turn ON or OFF each
time the [POWER] button is pressed. If the device doesn't turn ON and OFF, repeat this setup
procedure with the next code listed for the device.
3.
for an auxilliary device (optional)
NOTE
The red [AUX] button allows you to control a or a second TV or VCR if you aren't using it for a digital
Depending on
music terminal. To do this, you need to setup the [AUX] button so it functions like a second [TV] or
the configuration of
[VCR] button.
your cable box, certain
functions listed here
Press the [SETUP] button,then the [MENU] button on the remote.
may or may not
be functional.
Now, press the [AUX] button, and then the button that you want the [AUX] button to emulate (either
the [TV] or [VCR] button), then press the [SETUP] button. The red indicator light at the upper right-
hand corner of your remote will flash 3 times if these steps were followed correctly.
The [AUX] button can now be programmed to control the specific device. Follow the instructions above
in step 1 and press the [AUX] button any time you are told to press the [DEVICE] button.
Helpful
Hint
The setup code for the Jerrold ®
001
CFT2000 ™ series cable boxes is:
Jerrold® is a registered trademark of NextLevel Systems, Inc.
Memory Lock™ and the US Electronics logo are trademarks of US Electronics Components Corp.
All other trademarks are the property of their respective owners.