TABLE OF CONTENTS Page Table of Contents Owner’s Record Planning a Location For Your Hot Tub A Good Foundation Placing the Hot Tub Important Safety Instructions Safety Precautions Electrical Requirements Input Voltage Supply (Configuring SUV 120VAC/240VAC) Control Reference Guide 10-12 Frequently Asked Questions Featured Operations Fill Up and Start Instructions...
IMPORTANT: Freeflow Products Incorporated reserves the right to change specifications or design without notification and without any obligation. SPA DIMENSIONS Fantasy Model Width Length Height Dry Weight ILLUSION 66” (168cm) 77” (196cm) 29” (74cm) 255lbs (116kg) MIRAGE 75” (191cm) 75” (191cm) 33”...
PLANNING A LOCATION FOR YOUR HOT TUB Consider these things when determining where to place your new hot tub. SAFETY FIRST: Do not place the hot tub within 10 feet (3m) of overhead power lines. Make sure your hot tub is positioned so access to the equipment compartment and side panels will not be blocked.
A Good Foundation Your new hot tub needs a good solid foundation. The area your hot tub sits on must be able to support the tub, the water in it and those who use it. If the foundation is inadequate, it may shift or settle after the hot tub is in place, causing stress to the shell or components.
Important Safety Instructions It is the hot tub owner’s responsibility to read and follow all the instructions and precautions described in this manual. Failure to do so may result in personal injury. Liability rests with the hot tub owner. Please, make instructions available for reference by all hot tub users.
SAFETY PRECAUTIONS DANGER – RISK OF INJURY – READ AND FOLLOW ALL INSTURCTIONS 1. Read, keep, and make these instructions available! 104 °F (40°C) are considered safe for a healthy adult. Lower water temperatures are 2. Children should be CLOSELY supervised at all recommended for extended use (exceeding 10 to times.
ELECTRIC REQUIREMENTS DANGER – RISK OF ELECTRIC SHOCK Installations that do not conform to the following procedures and requirements may expose users to electric shock. Non-conforming installations will not be covered under warranty. If installed in the United States, the electrical wiring of this hot tub must meet the requirements of the National Electric Code (NEC) and any applicable state or local codes.
CONFIGURING SUV SYSTEM 120VAC/240VAC Input Voltage (120VAC/240VAC Convertible Pack) This Power System is supplied to utilize a 240V power supply (2 hot wires, a neutral wire, and a ground wire). If conversion to 120V is required, a jumper wire supplied with the system must be installed between J-16 and J35. Also, dip switch #10 must be set to the “On”...
CONTROLS REFERENCE GUIDE Illusion, Mirage, Vision, Espirit (120VAC/240VAC Convertible pack) Initial Start-up When your spa is first actuated, it will go into priming mode, indicated by “Pr.” The Priming mode will last for less than 5 minutes and then the spa will begin to heat the spa and maintain the water temperature in the Standard mode.
Refer to the Control Reference Card provided by Fantasy in your packet. * Note: Fantasy has designed the control panel, topside, to include: 1) Jets button 2) Light button 3) Down heat button 4) Up Heat button (Fantasy Spas currently does not offer air blowers.)
Page 12
Diagnostic Messages SUV- Models: Dream, Mirage, Vision, Espirit Message Meaning Action Required The control panel will be disabled until power No message on display. returns. Spa settings will be preserved until next Power has been cut off to the spa. power up.
Frequently Asked Questions Q. I have noticed water on the outside of my hot tub- is my hot tub leaking? A. A small puddle of water around the outside of your hot tub can be produced by water collecting and rolling off of your cover.
Featured Operations AIR CONTROL VALVE (when equipped) If your hot tub is installed with an Air Control Valve (Units equipped with a whirlpool will have two air control valves. The additional air control is for the whirlpool on the Mirage model. The air control valve serves to regulate the amount of air mixed with the water when the jets are operational.
Fill Up and Start Instructions The following procedures should be followed on initial startup and whenever the hot tub is drained for routine maintenance. FILLING THE HOT TUB WITH WATER 1. Clear all the debris from your hot tub. 2. Use a garden hose to fill your hot tub with water. NOTE: do not use home water heater or softened water.
Fantasy Spas strongly discourages the use of chemicals that contain Hydrogen Peroxide. Hydrogen peroxide will eventually cause the light body and lenses (used on all spas) to become brittle and crack.
Cleaning or Winterizing Every three to six months, depending upon the water condition, you may need to renew your water. CAUTION: READ THIS BEFORE DRAINING YOUR HOT TUB To prevent damage to the hot tub’s components, turn off power to the spa at the circuit breaker before draining the hot tub.
Spa Maintenance FILTER CARTRIDGE MAINTENANCE Fantasy hot tubs use a screw in filter cartridge that is easily removed. When the filter cartridge is removed, make sure no objects fall into the filter cavity. They can cause obstructions to the water movement. Every two weeks, the filter cartridge must be cleaned to remove the objects and particles that have lodged in the cartridge pleats.
COVER CARE Please keep your cover free from dirt at all times. Use a cover cleaner or a warm mild soapy water to clean the surface. Do not use any silicone-based products, as it will dry and may eventually crack the vinyl. NOTE: Do not stand on the cover at any time.
Troubleshooting Procedures In the event your Fantasy hot tub is not working the way it should, please first review all the installation and operating instructions in this manual and check the message on the panel display. If you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions.
Limited Warranty- Fantasy Series (Illusion,Mirage,Vision,Espirit) The Fantasy Series of spas is manufactured by Freeflow Products Incorporated, Ontario, CA. Five-Year Shell/Surface Warranty Freeflow Products, Inc. offers a shell warranty on manufacturing defects resulting in water loss for a period of five years from the date of manufacturing at 100% replacement of product for the first through the fifth year.