Fcc Part 68 Statement; Technical Specifications - EnGenius SN933 User Manual

Technical Specifications

Electrical Specifications Base Station
Frequency 915-928 MHz
Peak: 27 dBm
RF Output Power
Average: 21 dBm
Channel Spacing
Number of Channels
Modulation Differentially Encoded MSK
Multiple Access Frequency Hopping TDD
Frequency Hopping Rate 100 per second
TDD Frame Length
Number of Slots/Frame
<-111dBm (@ BER 10 -2 )
Receiver Sensitivity
Antenna Gain
Antenna Connector Reversed TNC
Telephone Interface
Channel Coding 8 kbps Convolutional + CRC
Transmission Data Rate 85.333 kbps
Speech Coding 8 kbps G.729AB
User Data Rate 64kbps duplex
Duplex Time Division Duplex (TDD)
Number of System ID
Ring Signal 20-50 Hz, 30-90 Vrms
Flash Time 100-900 ms programmable
Power Source AC/DC 5V/1A Adapter
Charger Current
Charge Time
FCC Part 15, Part 68
Regulation Compliance
ACMA Compliant
Operating Temperature
-40 – 70 °C
Storage Temperature
Humidity 20 – 75 %
Notes:
1.
NA = Not Applicable.
2.
The manufacturer reserves the right to change designs and specifications without
notice.
Portable Handset
915-928 MHz
Peak: 26 dBm
Average: 20 dBm
101 kHz 101 kHz
126 126
Differentially Encoded MSK
Frequency Hopping TDD
100 per second
10 ms 10 ms
4 4
<-111dBm (@ BER 10 -2 )
2 dBi Long: 2.5 dBi; Short: 1.5 dBi
Proprietary
RJ11 x 2 NA
8 kbps Convolutional + CRC
85.333 kbps
8 kbps G.729AB
64kbps duplex
Time Division Duplex (TDD)
65,536 65,536
NA
NA
3.7V/1100mAh Li-Ion Battery
550mA
NA
(550/850mA for desktop
charger)
NA 3hours
FCC Part 15, Part 68
Hearing Aid Compatible
ACMA Compliant
0 – 50 °C -10 – 60 °C
-40 – 70 °C
20 – 75 %
~61~

FCC Part 68 Statement

This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the bottom of SN933 base station is a label that contains,
among other information, a product identifier in the format US: SNIW403BFS2. If
requested, this number must be provided to the telephone company.
Applicable connector jack Universal Service Order Codes ("USOC") for the
Equipment is RJ11C.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: SNIW403BFS2. The digits
represented by 0.3 are the REN without a decimal point (e.g., 03 is a REN of 0.3).
If this SN933 causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required.
But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the operation of the equipment. If this happens
the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this SN933, for repair or warranty information, please
contact:
Company: Aristel Networks Pty Ltd. www.aristel.com.au
Address: 1/25 Howleys Road, Notting Hill, Victoria, 3168.
~62~