Related Manuals for Sunbeam EM0450
Summary of Contents for Sunbeam EM0450
- Page 1 Conical Burr Conical Burr Coffee Grinder Instruction Booklet EM0450 Please read these instructions carefully and retain for future reference.
-
Page 2: Table Of Contents
Contents Sunbeam’s Safety Precautions Features of your Conical Burr Coffee Grinder Operating your Conical Burr Coffee Grinder Adjusting the Grind Setting Care and Cleaning Important instructions – retain for future use. -
Page 3: Sunbeam's Safety Precautions
If you have any concerns regarding the performance and use of your appliance, please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line. Ensure the above safety precautions are understood. -
Page 4: Features Of Your Conical Burr Coffee Grinder
Features of your Conical Burr Coffee Grinder 250g Bean hopper The 250g capacity bean hopper has a shutter release mechanism for easy removal and preventing accidental spills. It allows the user to transfer any un-used beans to an ideal storage unit to preserve freshness. - Page 5 Burr shield Italian conical burrs Italian designed and manufactured, the metal conical burr design achieves excellent grind consistency and minimises heat transfer to the coffee due to the slowly rotating burrs. Group handle locator Cord stuff Hides away unwanted cord to keep bench top clean.
-
Page 6: Operating Your Conical Burr Coffee Grinder
Heading Operating your Conical Burr Coffee Grinder Before using the coffee grinder, wipe the 6.Select the grind by turning the grind base exterior with a damp cloth. Wash the adjustment collar to the desired setting, bean hopper, hopper lid and ground coffee see figure 2. - Page 7 Heading Operating your Conical Burr Coffee Grinder (continued) 8. To grind coffee, press the group handle 9. When the basket is full, pull the group against the button located in the centre handle off the button. Collapse the coffee of the group handle locator, see figure 4. in the basket by tapping it on the bench and repeat until the desired amount of coffee has been ground.
-
Page 8: Adjusting The Grind Setting
Heading Adjusting the Grind Setting A starting point for gring settings: 2. For drip filter coffee machines, a good starting point is to use 8 grams (1 scoop) SETTING BREWING METHOD of coffee for every 4 cups of brew water as measured with the carafe. -
Page 9: Care And Cleaning
Care and Cleaning Important Notes: 2.Clean the motor base exterior using a damp soft sponge with mild detergent • Spots and marks on the surface of the and wipe dry. burrs are part of the hardening process. These marks do not affect the performance 3.Wash the bean hopper and coffee container of the grinder or the taste of the coffee. - Page 10 Care and Cleaning (continued) 5.Lift the grind adjustment collar away from 3.Press and hold down the ‘UNLOCK’ button at the rear of the motor base and with the motor base and clean with the brush, see figure 9. the other hand turn the grind adjustment collar anti-clockwise until it stops and the graphic line on the collar is aligned with the line on the motor base, see figure 7.
- Page 11 Ensure the To inquire about having the burrs replaced marker on the top burr is aligned with the contact the Sunbeam Consumer Hotline on marker inside the grind adjustment collar Australia and push firmly into place.
- Page 12 Notes...
- Page 13 Notes...
- Page 14 Notes...
- Page 15 You are also Alternatively, you can send a written claim entitled to have the goods repaired or to Sunbeam at the address listed below. replaced if the goods fail to be of acceptable On receipt of your claim, Sunbeam will...
- Page 16 Sunbeam Corporation Limited 2006. ABN 45 000 006 771 Units 5 & 6, 13 Lord Street Botany NSW 2019 Australia Unit 3, Building D 26 Vestey Drive Mt Wellington Auckland New Zealand Sunbeam Corporation is a division of GUD Holdings Ltd. 8/11...