Husqvarna K3000 Operator's Manual
Husqvarna power cutter operator's manual
Hide thumbs
Also See for K3000:
- Operator's manual (24 pages) ,
- Operator's manual (20 pages) ,
- Operator's manual (20 pages)
Related Manuals for Husqvarna K3000
Summary of Contents for Husqvarna K3000
- Page 1 Operator’s manual K3000, K3000 Wet Please read the operator’s manual carefully and make sure you understand the E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols on the machine: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. -
Page 3: Table Of Contents
WHAT IS WHAT? What is what on the power cutter - K3000? ... WHAT IS WHAT? What is what on the power cutter - K3000 Wet? ... SAFETY INSTRUCTIONS Steps before using a new power cutter ... Personal protective equipment ... -
Page 4: What Is What
What is what on the power cutter - K3000? 1 Rear handle 2 Guard for the blade 14” 3 Cutting blade 4 Locking the axle 5 Front handle 6 Inspection covers 7 Power switch lock 8 Switch 4 – English... -
Page 5: What Is What
What is what on the power cutter - K3000 Wet? 1 Rear handle 2 Guard for the blade 3 Water kit 4 Cutting blade 5 Locking the axle 6 Front handle 7 Inspection covers 8 Power switch lock 9 Switch... -
Page 6: Safety Instructions
• Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs. WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. -
Page 7: Safety Instructions
SAFETY INSTRUCTIONS General safety warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electrtic shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ”power tool” in the warnings refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool. -
Page 8: Personal Safety
SAFETY INSTRUCTIONS Personal safety • Stay alert, watch what you are doing and use common sense when operaing a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 9: Machine's Safety Equipment
SAFETY INSTRUCTIONS Machine′ ′ ′ ′ s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine. -
Page 10: Cutting Blades
SAFETY INSTRUCTIONS Ground fault circuit interrupter (K3000 Wet) Ground fault circuit interrupters are for protection in case an electrical fault should occur. The LED indicates that the ground fault circuit interrupter is on and that the machine can be switched on. If the LED is not on, push the RESET button (green). -
Page 11: Diamond Blades
SAFETY INSTRUCTIONS Blade vibration The blade can become out-of-round and vibrate if an excessive feed pressure is used. A lower feed pressure can stop the vibration. Otherwise replace the blade. The blade must be of the recommended type for the material to be cut. Abrasive discs The cutting material on abrasive discs consists of grit bonded using an organic binder. -
Page 12: General Working Instructions
30–60 seconds and let it rotate in the air for 10 seconds to let it cool. Wet cutting with diamond blade (K3000 Wet) Water cooling, which is used when cutting concrete, cools the blade and increases its service life while also reducing the formation of dust. - Page 13 SAFETY INSTRUCTIONS • The guard for the cutting equipment should be adjusted so that the rear section is flush with the work piece. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user. •...
-
Page 14: Assembly
Fitting the cutting blade Husqvarna’s blades are approved for hand-held power cutters. Blades are manufactured with three different diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adjust the machine to the centre hole of the blade. -
Page 15: Starting And Stopping
Keep people and animals well away from the working area. Before starting (K3000 Wet) Water connector Connect the water hose to the water supply (A). The water flow is regulated using the water tap (B). -
Page 16: Maintenance
Maintenance WARNING! Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected. Cooling system The machine is equipped with an efficient fan to cool the motor. Cooling air which is drawn in through the grille by the machines rear handle passes over the stator and rotor and out through the front of the motor housing. -
Page 17: Daily Maintenance
Changing the grease The following parts must be dismantled to change the grease in the gear housing: 1 Flange washers holding the cutting blade 2 The sealing ring 3 Support flange for the guard 4 Guard for the blade 5 The four screws holding the shield. Lift the shield together with the drive wheel unit out of the gear housing. -
Page 18: Technical Data
Max. blade speed, rpm 4500 ´®z+S3•¶52¨ ´®z+S3•¶52¨ 18 – English TECHNICAL DATA K3000 100-120 2700/12 A 2200/20 A 15 A, 50-60 Hz 2300/10 A Type ”Gardena” K3000 Wet 100-120 2700/12 A 2200/20 A 15 A, 50-60 Hz 2300/10 A Type ”Gardena”... - Page 20 WARNING! Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Exposure to excessive amount of such dust can cause: Respiratory disease (affecting your ability to breath), including chronic bronchitis,...