Download Print this page

Husqvarna K 3000 Operator's Manual

Hide thumbs

Advertisement

Quick Links

Oper ator ' s manual
K3000
K3000 Wet
Please r ead the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

loading

  Related Manuals for Husqvarna K 3000

  Summary of Contents for Husqvarna K 3000

  • Page 1 Oper ator ′ s manual K3000 K3000 Wet Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
  • Page 2: Key To Symbols

    KEY T O SYMBOLS Symbols on the mac hine: Symbols in the operator’ s manual: W ARNING! The machine can be a dangerous tool if used incorrectly or Inspection and/or maintenance should carelessly, which can cause serious or be carried out with the motor switched fatal injury to the operator or others.
  • Page 3: Table Of Contents

    CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ........2 Symbols in the operator’s manual: ....... 2 CONTENTS Contents ............... 3 WHA T IS WHAT? What is what on the po wer cutter - K3000? ..4 WHA T IS WHAT? What is what on the po wer cutter - K3000 Wet? ..
  • Page 4: Wha T Is What

    WHA T IS WHA T? What is what on the po wer cutter - K3000? Rear handle Rating plate Guard for the blade 14” 10 Brush retainer Cutting blade 11 Carbon brushes Locking the axle 12 Guard for the blade 12” (Model version) Front handle 13 Connection for vacuum cleaner Inspection covers...
  • Page 5: Wha T Is What

    WHA T IS WHA T? What is what on the po wer cutter - K3000 Wet? Rear handle 10 Water tap Guard for the blade 11 Water connection with flow limiter Water kit 12 Rating plate Cutting blade 13 Brush retainer Locking the axle 14 Carbon brushes Front handle...
  • Page 6: General Safety Preca Utions

    • Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs. • Protective helmet •...
  • Page 7: Machine ' S Safety Equipment

    GENERAL SAFETY PRECA UTIONS Mac hine ′ ′ ′ ′ s safety equipment P ower switch lock The po wer switch lock is designed to prevent accidental This section descr ibes the machine ′ s safety equipment, operation of the switch. When the lock (A) is pressed in its purpose, and how checks and maintenance should be the power switch (B) is released.
  • Page 8 GENERAL SAFETY PRECA UTIONS Guar d for the blade This guard is fi tted above the cutting blade and is designed to prevent parts of the blade or cutting fragments from being thrown towards the user. Checking the blade guard WARNING! Always check that the guard is correctly fitted before starting the machine.
  • Page 9: Safety Instructions

    SAFETY INSTRUCTIONS General safety warnings Electrical safety • Power tool plugs must match the outlet. Never modify WARNING! Read all safety warnings and the plug in any way. Do not use any adapter plugs with all instructions. Failure to follow the earthed (grounded) power tools.
  • Page 10: Personal Safety

    SAFETY INSTRUCTIONS Personal safety Power tool use and care • Stay alert, watch what you are doing and use common • Do not force the power tool. Use the correct power tool sense when operaing a power tool. Do not use a for your application.
  • Page 11: Cutting Blades

    SAFETY INSTRUCTIONS Cutting blades Special blades Some cutting blades are designed for stationary equipment and for use with attachments.Such cutting WARNING! A cutting blade may burst blades must not be used on portable power cutters. and cause injury to the operator. Always contact local authorities and make sure you are following applicable directives.
  • Page 12: Transport And Storage

    SAFETY INSTRUCTIONS Abrasive blades for different materials Sharpening diamond blades Diamond blades can become dull when the wrong feeding Blade type Material pressure is used or when cutting certain materials such as heavily reinforced concrete. Working with a blunt Concrete, asphalt, stone diamond blade causes overheating, which can result in masonry, cast iron, aluminium, Concrete blade...
  • Page 13: General Working Instructions

    SAFETY INSTRUCTIONS General working instructions the material to be cut. This reduces the temperature of the blade and ensures effective cutting. WARNING! This section describes basic • The guard for the cutting equipment should be safety directions for using a power adjusted so that the rear section is flush with the work cutter.
  • Page 14 SAFETY INSTRUCTIONS How to avoid kickback Pull in Pull in occurs when the disc’s lower section suddenly WARNING! Kickback can happen very stops or when the cut closes. (To avoid, see the heading suddenly and violently; kicking the ”Basic rules” and ”Jamming/rotation”, here below.) power cutter and cutting blade back at Pinching/rotation the user.
  • Page 15: Assembly

    flange washers and the drive axle. See instructions under Fitting the cutting blade the heading Checking the drive axle and flange washers. Husqvarna’s blades are approved for hand-held power Checking the drive shaft and flange cutters. Blades are manufactured with three different washers diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/...
  • Page 16: Starting And Stopping

    STARTING AND STOPPING Before starting Starting • Grip the front handle with the left hand. WARNING! Note the following before • Grip the rear handle with your right hand. starting: The machine should be connected to an earthed outlet socket. Check that the mains voltage corresponds with that stated on the rating plate on the machine.
  • Page 17: Maintenance

    MAINTENANCE General turn can cause the ground fault circuit interrupter to turn off without intention. • Clean the machine daily by rinsing it with clean water after the work is finished. • Place the machine with the rear handle facing upwards.
  • Page 18: Bevel Gear

    MAINTENANCE Bevel gear Checking the drive shaft and flange washers The grease in the gear housing should be changed every 4 months. Use high quality gear grease Check that the threads on the drive shaft are undamaged. The gear housing must not be filled completely with Check that the contact surfaces on the blade and the grease.
  • Page 19: Technical Data

    TECHNICAL DATA Technical data K3000 K3000 Wet Engine Protection class Ground fault circuit interrupter Rated voltage, V Europe Great Britain USA / Canada / Japan 100-120 100-120 Australia Rated output, W Europe 2700/12 A 2700/12 A Great Britain 2200/20 A 2200/20 A USA / Canada / Japan 15 A, 50-60 Hz...
  • Page 20: Cutting Equipment

    TECHNICAL DATA Cutting equipment Cutting blade, mm/inches Max. peripheral speed, m/s 300/12 350/14 Max. blade speed, rpm 4500 Recommended cable dimensions Cable area 1,5 mm 2,5 mm Input voltage 100-120 V 20 m 40 m Input voltage 220-240 V 30 m 50 m 20 –...
  • Page 21: Ec-Declaration Of Conformity

    Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna K3000, K3000 Wet dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE: •...
  • Page 22 1153343-26 Original instructions ´®z+UB@¶60¨ ´®z+UB@¶60¨ 2009-12-29...

This manual is also suitable for:

K3000 wetK 3000 vacK3000