Code Alarm ca 3051 Installation Manual
  1. Manuals
  2. Brands
  3. Code Alarm Manuals
  4. Security System
  5. CA 3051
  6. Installation manual
Code Alarm ca 3051 Installation Manual

Code Alarm ca 3051 Installation Manual

Professional series keyless alarm
Hide thumbs Also See for ca 3051:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
PROFESSIONAL
SERIES
Keyless Alarm
Installation Guide
ca 3051
ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ca 3051 and is the answer not in the manual?

Questions and answers

Related Manuals for Code Alarm ca 3051

Summary of Contents for Code Alarm ca 3051

  • Page 1 PROFESSIONAL SERIES Keyless Alarm Installation Guide ca 3051 ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

  • Page 2: Before You Begin

    Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers. Technical Support (800) 421-3209 or go to http://techservices.codesystems.com ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

  • Page 3: Installation Of The Major Components

    It is suggested that the switch be mounted to the lower dash panel in the driver's area within reach of the driver. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 4 For vehicles with positive switching parking lights. Connect the White/Red wire to a +12 VDC constant battery source. b) For vehicles with negative switching parking lights. Connect the White/Red wire to a solid chassis ground source. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 5 +12 volt trunk control wire from the vehicles keyless entry system, or the switched +12 volt side of the vehicles trunk release solenoid. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 6 ARMED or a pulsed ground output to the factory door lock control relay for a passive door locking feature. The maximum current draw through these outputs must not exceed 300 mA. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 7 Diagram 1 Lock Fused + 12v + 12 Volts Lock Relay In Vehicle Diagram 2 Lock Fused + 12v + 12 Volts Door Lock Switch Door Lock Motor CUT HERE ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 8 For vehicles with single stage unlocking (all doors unlock with one press of UNLOCK on the OEM transmitter), connect the Lt Blue/Black to chassis ground. Note: You can select the polarity of this input by changing DIP Switch #2 ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 9 B. 2011 Audiovox Electronics Corporation. All rights reserved.

  • Page 10: Additional Ports

    Secure these looms along the routing using cable ties. This will ensure that the alarm wires are not damaged by falling onto hot or sharp moving surfaces in the vehicle. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

  • Page 11: Programmable Features

    5 Passive Arming Passive Active 6 Entry Delay 15 Second Delay Instant Siren 7 Siren / Horn Output Horn Instant 8 Door Ajar Warning 30 Second Default Settings are in BOLD ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 12 CA 3051 1 - 8 ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.
  • Page 13 B. 2011 Audiovox Electronics Corporation. All rights reserved.

  • Page 14: Fcc Compliance

    2. This device must accept any interference received, including any interference that may cause undesired operation. Warning! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ca3051 rev B. 2011 Audiovox Electronics Corporation. All rights reserved.

Table of Contents