Page 1
Operator’s manual (EPA) 323C 325CX 323L 325LX 323LD 325LDX Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
KEY TO SYMBOLS Symbols Only intended for trimmer heads. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully Other symbols/decals on the machine and make sure you understand the refer to special certification requirements for certain...
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the Symbols ............... design and appearance of products without prior notice. CONTENTS Contents ..............
SAFETY INSTRUCTIONS Personal protective equipment Machine ′ ′ ′ ′ s safety equipment This section describes the machine ′ s safety equipment, its IMPORTANT! You must use approved personal protective purpose, and how checks and maintenance should be carried equipment whenever you use the machine. Personal out to ensure that it operates correctly.
SAFETY INSTRUCTIONS Vibration damping system For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See Your machine is equipped with a vibration damping system instructions under the heading Checking, maintaining and that is designed to minimize vibration and make operation servicing the machine’s safety equipment.
SAFETY INSTRUCTIONS Checking, maintaining and servicing Stop switch the machine ′ ′ ′ ′ s safety equipment • Start the engine and make sure the engine stops when you move the stop switch to the stop setting. IMPORTANT! All servicing and repair work on the machine requires special training.
SAFETY INSTRUCTIONS • Regularly check that the muffler is securely attached to • Tighten the nut using the socket spanner. 35-50 Nm (3.5- the machine. 5 kpm). CAUTION! The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm.
SAFETY INSTRUCTIONS • Observe your surroundings and make sure that there is no WARNING! Always stop the engine before risk of people or animals coming into contact with the doing any work on the cutting attachment. cutting equipment. This continues to rotate even after the •...
SAFETY INSTRUCTIONS • When storing the machine for long periods the fuel tank 5 Never put the machine down with the engine running must be emptied. Contact your local gas station to find out unless you have it in clear sight. where to dispose of excess fuel.
Page 10
SAFETY INSTRUCTIONS Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
ASSEMBLY Fitting the loop handle Assembling and dismantling the two-piece shaft (325C, 325Cx) (325LDx) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. Assembly: • Make sure the knob is loose. •...
ASSEMBLY Fitting the trimmer head To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread). When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment.
ASSEMBLY Fitting the trimmer guard and Fitting the trimmer guard and trimmer head trimmer head (325C) (325Cx) • Fit the guard as shown in the diagram. Tighten securely. Guard • Fit the guard as shown in the diagram. Tighten securely. •...
Always shut off the engine before refuelling. Always stop the engine and let it cool for a • For best results and performance use HUSQVARNA two- few minutes before refuelling. stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%).
STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support WARNING! The complete clutch cover and flange if it is cracked. shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.
Page 17
STARTING AND STOPPING some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle;...
CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful Rec. idle speed 2700 rpm emissions.
MAINTENANCE Correctly adjusted carburettor will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts When the carburettor is correctly adjusted the machine will to rotate. accelerate without hesitation and burble a little at maximum speed.
filter. if necessary. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder.
• Check electrical wires and connections. • Replace the spark plug. Check that the spark plug is fitted CAUTION! Use only HUSQVARNA replacement parts. Use with a suppressor. of other brands of replacement parts can cause damage to • Change the air filter.
Forest & Garden cannot deny warranty solely for the lack of servicing dealer or call Husqvarna Forest & Garden at 1-800- receipts or for your failure to ensure the performance of all 487-5963.
Page 26
Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
Need help?
Do you have a question about the 323C and is the answer not in the manual?
Questions and answers