VTech DS6321-2 Quick Start Manual

Quick start guide

for models DS6321-2/DS6321-3/
DS6321-4/DS6322-3/DS6322-4
Install the telephone base
Install the telephone base and charger(s) as
shown below.
Electrical outlet not
controlled by a wall switch
Telephone wall jack
Telephone
base power
adapter
Telephone line cord
DSL filter (not
included) is required
if you have DSL high
speed Internet service
Electrical outlet
not controlled by
a wall switch
Telephone base
Power
adapter
Charger
• Use only the power adapters and batteries supplied
with your VTech telephone.
• For complete feature instructions, please refer to your
user's manual.

Battery installation and charging

Install the battery as shown below. For optimal
performance, charge the handset battery for at
least 16 hours before use.
1. If the battery 2. Plug the battery
compartment cover connector securely
is on the handset, into the socket
press the indentation inside the handset
and slide the cover to battery compartment,
remove. matching the color-
coded label.
3. Place the battery with 4. Align the cover flat
the label THIS SIDE against the battery
UP facing up and the compartment, then
wires inside the battery slide it towards the
compartment. center of the handset
until it clicks into place.
CHARGE
light
5. Charge the handset
by placing it in the
telephone base or
charger. The CHARGE
light is on when the
handset charges.
Pair your first Bluetooth cell phone
To pair and connect your first Bluetooth cell phone:
1. Press MENU/ on the
SELECT
handset.
Ans. system
2. Press or to highlight Directory
Cal l log
Bluetooth, then press
Intercom
/SELECT.
MENU
Bluetooth
3. Press or to highlight
Add cellular, then press
/SELECT. The screen BLUETOOTH
MENU
Download dir
displays ADD CELLULAR
Add cel lular
Place cell phone next to
Add headset
base. Press SELECT.
Active devices
4. Press /SELECT.
MENU
The screen displays
ADD CELLULAR
Please set your cell phone
Place cel l
to search for devices, then
phone next to
press SELECT.
base.
Press SELECT
5. Turn on the Bluetooth feature of
your cell phone and search for
or add new devices.
Please set your
6. Press /SELECT to set the
cel l phone to
MENU
telephone base to discoverable search for
devices, then
mode.
press SELECT
7. Once your cell phone finds your
VTech DS6321/VTech DS6322,
press a key on your cell phone
to confirm the connection. Base name:
VTech DS6321
8. Enter the PIN of the telephone
PIN:0000
base (the default PIN is 0000)
into your cell phone.
Cel lular setup
9. When successfully connected,
completed
the handset displays
Cellular setup completed
Device
Device connected and the
connected
corresponding status icon
( 1 or 2). The
corresponding device light on
the telephone base (DEVICE1
or DEVICE2) turns on.
• The pairing process may take up to one minute. If the
pairing process fails, try again.
• If you put the handset back in the telephone base
or charger while pairing, the process stops and the
handset returns to idle mode.
Pair your first Bluetooth headset
To pair and connect your first Bluetooth headset:
A paired Bluetooth headset can be
used for making and receiving
Ans. system
home calls.
Directory
Cal l log
1. Press MENU/ on the
SELECT
Intercom
handset.
Bluetooth
2. Press or to highlight
Bluetooth, then press
BLUETOOTH
/SELECT.
MENU
Download dir
Add cel lular
3. Press or to highlight
Add headset
Add headset, then press
Active devices
/SELECT. The screen
MENU
displays ADD HEADSET Place
Bluetooth headset next to
ADD HEADSET
base. Press SELECT.
Place Bluetooth
/SELECT.
4. Press headset next to
MENU
base.
The screen displays
Press SELECT
Please set your headset to
discoverable mode, then
press SELECT.
Please set your
5. Set your headset to headset to
discoverable mode. discoverable
mode, then
6. Press /SELECT to
MENU
press SELECT
set your telephone base to
discoverable mode and search
for your headset.
Searching for
Bluetooth
7. Once the telephone base
headsets...
finds your headset, press
/SELECT.
MENU
8. Enter the PIN of your headset
(the PIN for most Bluetooth
FOUND DEVICES
devices is 0000), then press
Headset A
/SELECT.
MENU
Headset B
9. When the handset displays
Headset A paired to base.
Connect now? Press
SELECT, then press
ADD HEADSET
/SELECT.
MENU
Enter PIN:
10. When successfully connected,
the handset displays
Headset setup completed
Device connected and the
corresponding status icon
( 1 or 2). The Headset A
paired to base.
corresponding light on the
Connect now?
telephone base (DEVICE1 or
DEVICE2) turns on.
Press SELECT
• The pairing process may take
Headset setup
up to one minute. If the pairing
completed
process fails, try again.
• If you put the handset back in the
telephone base or charger while Device
pairing, the process stops and the connected
handset returns to idle mode.
----