Sony CDX-GT620 Operating Instructions Manual page 24

FM/AM
COll1pact
Disc Player
SONY
Installation/Connections
Installation/Connexions
3-285-540-11 (1)
m
A
CDX-GT620IP
CDX-GT62IPW
- -
B
©
2008 Sony Corporation Printed in Thailand
Connection diagram []]
Connection example
[l]
Notes
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
o
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
e
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster. or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
o
To the interface cable of a car telephone
e
To a car's illumination signal
Be sure to connect the black ground (earth) lead to a meJal
surface of the car first.
o
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the + 12 V
power (battery) terminal which
is
energized
at
all times.
Be sure to connect the black ground (earth) lead to
a
metal surface of the
car
first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
o
To the +12 V power terminal which is
energized at all times
Be sure
to
connect the black ground (earth) lead to
a
metal
surface of the car first.
Note
Before installing, make sure that the catches on both sides of
the bracket
CD
are bent inwards 2 mm (Y32 in). If the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.
Cautions
Parts list
[I]
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
o
The numbers in the list are keyed
to
those in thc
instructions.
o
The bracket
CD
and the protection collar
@
are
attached to the unit before shipping. Before mounting
the unit, use the release keys
®
to remove the bracket
CD
from the unit. For details, see "Removing the
protection collar and the bracket
(EI)"
on the reverse
side of the sheet.
o
Keep the release keys
®
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
o
This unit is designed for negative ground (earth) 12 V
DC operation only.
o
Do not get the leads under a scrcw, or caught in moving
parts (e.g. seat railing).
o
Before making connections, turn the car ignition off to
avoid short circuits.
o
Connect the yellow and red power supply leads only
after all other leads have been connected.
o
Run all ground (earth) leads to a common
ground (earth) point.
o
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
o
The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
o
When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
o
When no car circuits are rated high enough, connect
the unit directly to the battery.
®
iPod
x2
Rotary commander RM-X4S
Satellite de commande RM-X4S
Power amplifier
Amplificateur de puissance
x4
®
®
Active subwoofer
Caisson de graves actif
Rear speaker
Haut-parleur arriere
Front speaker
Haut-parleur avant
Equipment used in illustrations (not supplied)
Appareils utilises dans les illustrations (non fournis)
o