Table of Contents
Advertisement
General
Output:
Audio outputs terminal (front, sublrear switchable)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
Telephone ATT control terminal
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
iPod signal input terminal (dock connector)
Tone controls:
Low: ±1O dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±IO dB at 10 kHz (XPLOD)
Power requirements: 12
V
DC car battery
(negative ground (earth»
Dimensions: Approx. 178
x
50
x
180 mm
(7
lis
x 2 x 7 lis
in)
(w/h/d)
Mounting dimensions: Approx. 182
x
53
x
162 mm
(7
1
14
x
2
lis x
6
1
/2 in) (wlh/d)
Mass: Approx. 1.3 kg (2 Ib 14 oz)
Supplied accessories:
Card remote commander: RM-X151
Parts for installation and connections
(1
set)
Optional accessory:
Rotary commander: RM-X4S
Your dealer may not handle some of the above listed
accessory. Please ask the dealer for detailed
information.
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer lIS and Thomson.
This product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
Design and specifications are subject to change
without notice.
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Halogenated flame retardants are not used in
cabinets.
• Packaging cushions are made from paper.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check the
connection and operating procedures.
No power is being supplied to the unit.
• Check the connection. If everything is in order, check
the fuse.
• If
the unit is turned off and the display disappears, it
cannot be operated with the remote commander.
-+
Turn on the unit.
The power antenna (aerial) does not extend.
The power antenna (aerial) does not have a relay box.
No sound.
• The volume is too low.
• The ATT function is activated, or the Telephone ATT
function (when the interface cable of a car telephone
is connected to the ATT lead) is activated.
• The position of the fader control "FAD" is not set for
a 2-speaker system.
II
No beep sound.
• The beep sound is canceled (page 12).
• An optional power amplifier is connected and you are
not using the built-in amplifier.
The contents of the memory have been erased.
• The RESET button has been pressed.
-+
Store again into the memory.
• The power supply lead or battery has been
disconnected.
• The power supply lead is not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the ignition
is switched.
The leads are not matched correctly with the car's
accessory power connector.
During playback or reception, demonstration
mode starts.
If
no operation is performed for 5 minutes with
"DEMO-ON" set, demonstration mode starts.
-+
Set "DEMO-OFF' (page 12).
The display disappears from/does not appear
in the display window.
• The dimmer is set "DIMMER-ON" (page 12).
• The display disappears if you press and hold
(OFF).
-+
Press and hold
(OFF)
on the unit until the
display appears.
• The connectors are dirty (page 17).
The Auto Off function does not operate.
The unit is turned on. The Auto Off function activates
after turning off the unit.
-+
Turn off the unit.
continue to next page --
19
Advertisement
Table of Contents
