Advertisement
FOREWORD This manual is a guide to introduce you to the Kreepy Krauly
Marathon System. It cannot cover the requirements of every installation, so
please contact your local distribution centre for further advice should you need it.
INTRODUCTION
Congratulations on the purchase of your Kreepy Krauly Marathon automatic
pool cleaning system. It is designed to prevent your pool from ever getting
dirty and will provide you with many extra hours of leisure in and around your
swimming pool.
The Kreepy Krauly System requires no power source, operates hydraulically and
has a 2 year warranty from the date of purchase, excluding fair wear and tear.
The only working part in the Kreepy Krauly System is the Flow Valve which is
guaranteed for 10 years. The system has 3 major components, the Cleaner
Unit, Special Hose and the Vacuum Plate with anti-surge and AutoSkim valves.
Hose Weight
Retaining
Hose
Collar
Protector
Sleeve
Anti Vortex
Washer
Auto Skim
Valve
Vent
Valve
Vacuum
Plate
VACUUM PLATE
HOW IT WORKS
Water flow from the main body assembly is alternately diverted into either the
top or bottom drive tubes of Kreepy Krauly. The inertia of water trapped in
each of the drive tubes provides a lifting and propelling action.
In operation, Kreepy Krauly travels around the pool, trailing the vacuum hose
and the hose weights neutralize floatation of the vacuum hose near to Kreepy
Krauly.
The combined vacuum plate control and AutoSkim valve supplied with Kreepy
Krauly regulates the amount of vacuum supplied by the fi ltration system, also
allowing pool surface skimming (providing the pool filtration system has an
adequate flow).
For effective operation of Kreepy Krauly, all water flow through the main
drain must be effectively blocked off. Kreepy Krauly will vacuum clean any
well equipped pool, but it will not overcome problems associated with
inadequate or improperly maintained filtration systems. The vacuum cleaning
performance depends upon having an adequate filter system properly cleaned
and maintained. This means that your pump and filter system should be
operating effi ciently. There must be good water flow into the suction side of the
pump (skimmer) and good discharge from the pool inlet. All plumbing lines
should be clear, strainer basket should be emptied and sand filters should be
backwashed. Diatomaceous earth filters should be cleaned and recharged in
accordance with their manufacturer's instructions. Cartridge filters should be
thoroughly and carefully cleaned.
Swivel Head
Assembly
Dive Float
Assembly
Bumper
Strap
Pilot Weight
Assembly
Pleated
Scoop
Seal
ANTI VORTEX
AUTO SKIM
WASHER
VALVE
ASSEMBLING YOUR KREEPY KRAULY
Please read this manual carefully before assembly and installation of your Kreepy
Krauly. Like all pool equipment, periodic maintenance is required so please refer
to the maintenance section of this manual for normal maintenance requirements.
Kreepy Krauly is shipped to you partly assembled. Remove all the parts from the
box. Assemble your Kreepy Krauly on a clean working surface. The hose and
vacuum plate assembly are packed in separate cartons from the machine.
STEP 1
Attach scoop as shown.
STEP 3
Main Body
Assembly
Install both slip rings underneath
the seal as shown.
STEP 5
The bumper strap fits tightly into the main body as shown.
The other end is fitted into the swivel head. Ensure full insertion.
STEP 6
To relieve any coiling in the hose after delivery or long storage lay the hose in a
straight line beside your pool for one hot and sunny day before installation (28°C or
above). Alternatively the hose may be filled with warm but not boiling water whilst
lying in a straight line. This procedure can be used when the weather is cooler.
1. Detach the hose from the Kreepy Krauly and lay it beside the pool on a flat
surface and in a straight line.
2. One end of the hose should also be close to the pool inlet.
3. Prop up both ends of the hose about 0.2 metre's above the ground.
4. Fill a bucket with warm water (around 50-60°C) and pour this water into the
hose until it spills out of the other end.
5. Carefully roll the hose backwards and forwards to ensure even warm up.
6. After 30 to 40 seconds fill the hose with cold water. This can be done by either
using the bucket or by placing the hose end on the pool outlet whilst the pump
is working. The hose will now be relaxed and ready to be installed with your
Kreepy Krauly.
The Scoop
STEP 2
The Pleated Seal or optional
premium performance silicone
seal are fitted as shown. Once
fitted it should rotate freely.
Observe the warning "this side up".
Slip-Rings
STEP 4
The sole is fitted to the foot of the
main body as shown.
Bumper Strap
Relaxing your Kreepy Krauly Hose
when fi rst taken from the box.
Pleated Seal
The Sole
Advertisement
