Toshiba RAV-SM566KRT-E Owner's Manual page 10

Automatic operation
(auto changeover)
◆ Start
3
4
PRESET FAN
TEMP
1
MODE
2
1
START/STOP button ( )
Press this button to start the air conditioner.
2
Mode select button (MODE)
Select A.
3
Temperature button ( )
TEMP
Set the desired temperature.
4
Fan speed button (FAN)
+
Select one of LOW , LOW
+
MED , MED , HIGH
• The OPERATION lamp (green) on the display
panel of the indoor unit lights.
The operating mode is selected in accordance with
the room temperature and operation starts after
approximately 3 minutes.
• If the "A" mode is uncomfortable, you can select the
desired conditions manually.
◆ Stop
START/STOP button ( )
Press this button again to stop the air conditioner.
17-EN
Timer operation
Use the wired remote controller for timer setting if it is
also in use.
◆ ON timer and OFF timer
PRESET FAN
TEMP
MODE
COMFORT
QUIET SLEEP
SWING FIX Hi-POWER
TIMER CLR
ON OFF
SLEEP SET
CHK FILTER CLOCK
Setting TIMER
1
Push ON / OFF TIMER button ( or ) during
,
operation.
.
Press the ON or OFF TIMER buttons as required.
• The previous timer setting is displayed and
flashes along with ON / OFF timer display.
Set the timer to the desired time.
Each press of the TIMER button changes the time
in ten minute steps.
Pressing the TIMER button continually changes
the time in one hour step.
2
SET button
SET
Press the SET button to set the timer.
SET
The timer time is indicated and the timer starts.
Cancelling TIMER
3
CLR button
CLR
Press the CLR button to cancel the timer
CLR
setting.
– 9 –
CAUTION
• When you select the timer operation, the remote
controller automatically transmits the timer signal to
the indoor unit at the specified time. Therefore, keep
the remote controller in a location where it can
transmit the signal to the indoor unit properly.
Otherwise, the time lag of up to 15minutes will occur.
• If you do not press the SET
seconds after setting the time, the setting will be
cancelled.
Once you select the timer operation mode, the settings
are saved in the remote controller.
Thereafter, the air conditioner will start operating under
the same conditions when you simply press the ON /
OFF button of the remote controller.
If the clock display is flashing, you cannot set the timer.
Follow the instructions in the section "Setting the clock"
1
and then set the timer.
3
◆ Combined timer (Setting both ON
2
and OFF timers simultaneously)
OFF timer —> ON timer
(Operation —> Stop —> Operation)
ON OFF
This feature is useful when you want to stop the air
conditioner after you go to sleep, and start it again in
the morning when you wake up or you return home.
Example:
To stop the air conditioner and start it again next
morning.
Operation
▼ Setting combined TIMER
1
Press the OFF TIMER
OFF timer.
2
Press the ON TIMER
ON timer.
3
Press the SET
ON timer —> OFF timer
(Stop —> Operation —> Stop)
You can use this setting to start the air conditioner
when you wake up and stop it when you leave the
house.
Example:
To start the air conditioner next morning and stop it.
button within 30
SET
Stop
▼ Setting combined TIMER
1
Press the ON TIMER
ON timer.
2
Press the OFF TIMER
OFF timer.
3
Press the SET
• Either ON or OFF timer function which is closer to
the current time, is activated first.
• If the same time is set for both ON and OFF timers,
no timer operation is performed.
Also, the air conditioner may stop operating.
◆ Every day combined timer
(setting both ON and OFF timer
simultaneously and activate every
day)
This feature is useful when you want to use combined
Operation again
timer at the same time every day.
Stop
▼ Setting combined TIMER
1
Press the ON TIMER
ON timer.
2
Press the OFF TIMER
button to adjust the
OFF timer.
OFF
3
Press the SET
button to adjust the
4
ON
After step 3, an arrow mark (
for about 3 seconds and during this flashing,
button.
press the SET
SET
• During the every day timer is activating, both arrows
( , ) are indicated.
Operation
Stop
button to adjust the
ON
button to adjust the
OFF
button.
SET
button to adjust the
ON
button to adjust the
OFF
button.
SET
or ) flashes
button.
SET
18-EN