Subwoofer Outputs; Status Led / Protection Circuitry - JL Audio XD1000/1v2 Owner's Manual

PREOUTS
through preamp output section, so that additional
amplifiers can be easily added to the system.
The preamp output delivers the same signal that
The preamp output signal is not affected by
range, the preamp output will be full-range).
If you plan to use the "Preouts" to feed
a stereo amplifier, you must connect a
stereo signal to the input of the amplifier.
A mono signal into the amplifier will result
in a mono signal out of the preamp output.
10 | JL Audio - XD1200/1v2 Owner's Manual

SUBWOOFER OUTPUTS

into subwoofer loads equal to or greater than 2
ohms of nominal impedance.
designed to accept 16 AWG - 8 AWG wire. To
connect the subwoofer wires to the amplifier,
first back out the set screws on the top of the
terminal block, using the supplied 2.5 mm hex
wrench. Strip 1/2 inch (12 mm) of insulation
from the end of each wire and insert the bare
wire into the terminal block, seating it firmly
so that no bare wire is exposed. While holding
the wire in place, tighten the set screw firmly,
taking care not to strip the head of the screw.
+ positive
–
This is to facilitate multiple subwoofer wiring.
The two positive and two negative connections
are connected in parallel inside the amplifier.
They are not stereo outputs. Connecting two
subwoofers, each to one set of positive and
negative terminals, will result in a parallel
subwoofer connection. When only connecting
one pair of subwoofer wires, it is not necessary to
use both sets of connections.
Subwoofer loads below 2 ohms nominal are not
recommended and may cause the amplifier
to initiate a protection mode, which reduces
power output.

STATUS LED / PROTECTION CIRCUITRY

surface of the amplifier to indicate the amplifier's
operating status.
1) Flashing Green: amplifier is powering up,
audio output is muted.
2) Constant Green: amplifier is on and
functioning normally, audio output is active.
3) Constant Red: lights to indicate that the
amplifier has exceeded its safe operating
temperature, putting the amplifier into a
self-protection mode, which reduces the
peak power output of the amplifier without
muting the audio. When its temperature returns
to a safe level, the red light will return to green
and the amplifier will return to full power
operating mode.
4) Constant Amber (Yellow): Indicates
that an over-current condition has occurred and
is accompanied by a muting of the amplifier's
output. Because the muting behavior may be
very short in duration, it may manifest itself as
an audible, repetitive ticking or thumping noise
in the output. Over-current conditions can be
caused by a speaker impedance lower than the
optimum load impedance range for the amplifier
or a short-circuit in the speaker wiring. The
latter can result from a short circuit between the
positive and negative speaker wires or between
either speaker wire and the vehicle chassis.
Status LED
seconds, even if the over-current condition is of a
very short duration.
5) LED off / Amplifier Shuts Off Unexpectedly
The only condition that will shut down
battery voltage or remote turn-on voltage drops
Status LED
when this occurs. The amplifier will turn back
on when voltage climbs back above 11 volts.
If this is happening in your system, have your
charging system and power wiring inspected.
For more information on troubleshooting this
.
SERVICING YOUR JL AUDIO AMPLIFIER
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation
of more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier that have not been covered
in this manual, please contact your dealer or
technical support.
JL Audio Technical Support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
11