Download Print this page

Advertisement

© Electrolux Distriparts
Muggenhofer Straße 135
D-90429 Nürnberg
Germany
Fax +49 (0)911 323 1022
DGS-TDS-N
11.08
Edition:
SERVICE INSTRUCTION
Publ.-Nr.:
599 529 016
685
EN
COOKERS
Autark cooker hob with
induction
„Maxima Extension"
Service instructions
- 3 and 4 cooking zones
„Maxima Extension"
- 5 cooking zones

Advertisement

loading

Summary of Contents for Electrolux COOKERS

  • Page 1 SERVICE INSTRUCTION COOKERS Autark cooker hob with induction „Maxima Extension“ Service instructions © Electrolux Distriparts Publ.-Nr.: - 3 and 4 cooking zones Muggenhofer Straße 135 599 529 016 „Maxima Extension“ D-90429 Nürnberg - 5 cooking zones Germany Fax +49 (0)911 323 1022 DGS-TDS-N 11.08...
  • Page 2: Table Of Contents

    Induction hobs with 3 respectively 4 cooking zones „Maxima Extension“ ......4 Induction hobs with 5 cooking zones .................. 6 Notes for interventions on the device .................. 8 Error analysis ........................11 Changes ............................13 DGS-TDS-N 11.08 U.H. © Electrolux - 2 - 599 529 016...
  • Page 3: Esd=Electrostatic Discharge

    Endangered are all assembly groups which are provided with control entries, wire paths lying open and free-accessible processors. DGS-TDS-N 11.08 U.H. © Electrolux - 3 - 599 529 016...
  • Page 4: Appliance Variants

    Appliance variants Induction hobs with 3 respectively 4 cooking zones „Maxima Extension“ (Sample illustration ... with 4 cooking zones) DGS-TDS-N 11.08 U.H. © Electrolux - 4 - 599 529 016...
  • Page 5 DGS-TDS-N 11.08 U.H. © Electrolux - 5 - 599 529 016...
  • Page 6: Induction Hobs With 5 Cooking Zones

    Induction hobs with 5 cooking zones (Sample illustration) DGS-TDS-N 11.08 U.H. © Electrolux - 6 - 599 529 016...
  • Page 7 DGS-TDS-N 11.08 U.H. © Electrolux - 7 - 599 529 016...
  • Page 8: Notes For Interventions On The Device

    Care should be taken with regard to the two right connections that when making a replacement, the non-occupied connections must also be tightened using a screwdriver (for induction hobs with 3 cooking zones). DGS-TDS-N 11.08 U.H. © Electrolux - 8 - 599 529 016...
  • Page 9 Fig.: Design without inductors Fig.: Torx sheet metal screw Fig.: Phillips screw The carrier plate can be removed after all of the screws have been removed and the earthed conductor disconnected. DGS-TDS-N 11.08 U.H. © Electrolux - 9 - 599 529 016...
  • Page 10 The wiring should also be replaced if the plug area of the defective filter module should show signs of burnout stages. DGS-TDS-N 11.08 U.H. © Electrolux - 10 - 599 529 016...
  • Page 11: Error Analysis

    R.H. indication "E" (E4) Both modules not programmed Install new filters Right module not programmed, sensor for the Install new filter. R.H. indication "E" (E4) right cooking plate defective Replace coil DGS-TDS-N 11.08 U.H. © Electrolux - 11 - 599 529 016...
  • Page 12 Activate fuse Module right defective Fusing/conductor rail of the filter right defective Replace performance part and filter Connection line between the modules Replace line Control unit defective Replace control unit DGS-TDS-N 11.08 U.H. © Electrolux - 12 - 599 529 016...
  • Page 13: Changes

    Changes Pages 1 - 13 changed DGS-TDS-N 11.08 U.H. © Electrolux - 13 - 599 529 016...