Summary of Contents for Onnto 2.5" SATA HDD Enclosure
Page 1
The product information provided in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor. The vendor assumes no liability or responsibility for any errors that may appear in this manual Copyright 2007, Onnto Corporation. All rights reserved. Version 02...
2.5” SATA HDD Enclosure User’s Manual Introduction ....................... 3 Important Reminders for all Enclosures............3 Getting Started....................4 System Requirements................... 4 Package Contents ..................4 USB2.0 HDD Enclosure Package Contents ........4 eSATA/USB 2.0 HDD Enclosure Package Contents......5 Installing the HDD in the 2.5” SATA HDD Enclosure ........5 Connecting the 2.5”...
Introduction Thank you for your purchase of the 2.5” SATA Hard Disk Drive Enclosure. Your 2.5” SATA Hard Disk Drive Enclosure offers fast and reliable data transfer. Proper installation, care and use, as described in the User’s Manual will ensure trouble-free use and prolong the life of your 2.5” SATA HDD Enclosure.
Getting Started Please review the System Requirements and Package Contents for your particular model. For best results, please read all the instructions provided in the User’s Manual prior to attempting installation. The installation instructions in this manual apply to the following models. •...
eSATA/USB 2.0 HDD Enclosure Package Contents • Enclosure x 1 • eSATA cable x 1 • USB-A to mini B cable x eSATA/USB 2.0 USB-A to DC Jack to Quick Start Fastening Enclosure eSATA Cable mini B Cable USB-A Y Cable Guide Screws •...
Page 6
Slide the 2.5” SATA HDD into the HDD tray Locate the four HDD fastening screws included in the Enclosure package. Turn the Enclosure bottom side up. Fasten the HDD to the HDD tray by inserting the screws using a Phillips screwdriver. Slide the assembled HDD tray into the Enclosure housing bottom side up.
Page 7
Ensure that the guide marks on the panel are properly aligned with the guide marks on the Enclosure housing. Fasten the front panel to the Enclosure housing by replacing the screws removed in step 1. The 2.5” SATA HDD Enclosure is now ready for connection to a Host Computer.
Connecting the 2.5” SATA HDD Enclosure to a Host USB 2.0 model Connect the DC Jack to USB cable to the DC IN port FIRST. Ensure that the DC Jack to USB cable is connected before attempting to connect the USB 2.0 cable to the host computer Connect the available end of the DC Jack to USB 2.0 cable to the host computer.
Connect the free end of the USB A to mini B cable to an available USB 2.0 port on the host computer. You are now ready to use your 2.5” SATA HDD Enclosure. eSATA/USB 2.0 model Connect the DC Jack to USB Y-cable to the DC IN port FIRST. If the USB 2.0 connector is selected for data transfer, connection to only one USB port on the host computer via Y-cable is required.
Page 10
Note: To protect your HDD, it is highly recommended that you first connect the DC-Jack to USB power cable to the 2.5” SATA HDD Enclosure. If the USB A to mini B data cable is connected to the computer host and then connected to the 2.5”...
Using the DC Jack to USB Y-cable (USB 2.0/eSATA model only) The DC Jack to USB Y-cable provides 2 USB type-A connectors and 1 DC Jack connector. If USB 2.0 connection is selected as the primary data transfer interface, insert only one USB type-A connector of the Y-cable into the host.
Notices and Classifications FCC-B Radio Frequency Interference Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.