Advertisement
2.5" SATA HDD Enclosure
Speedy Data Transfer and Flexible Connectivity
User's Manual
The product information provided in this manual is subject to change without prior
notice and does not represent a commitment on the part of the vendor. The
vendor assumes no liability or responsibility for any errors that may appear in this
manual
Copyright 2007, Onnto Corporation. All rights reserved.
Version 02
Advertisement
Related Manuals for Onnto 2.5" SATA HDD Enclosure
Summary of Contents for Onnto 2.5" SATA HDD Enclosure
- Page 1 The product information provided in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor. The vendor assumes no liability or responsibility for any errors that may appear in this manual Copyright 2007, Onnto Corporation. All rights reserved. Version 02...
-
Page 2: Table Of Contents
2.5” SATA HDD Enclosure User’s Manual Introduction ....................3 Important Reminders for all Enclosures ............3 Getting Started .....................4 System Requirements ..................4 Installing the 2.5” SATA HDD ...............5 Connecting the Enclosure to a Computer.............9 Notices and Classifications ................12 Version 02... -
Page 3: Introduction
Introduction Thank you for your purchase of the 2.5” SATA to eSATA/USB 2.0/FireWire (800) Hard Disk Drive (HDD) Enclosure. Your 2.5” SATA HDD Enclosure offers fast and reliable data transfer. The groundbreaking DuoLink 2-in-1 eSATA/USB connector combines eSATA and USB 2.0 connectivity in a single port. Proper installation, care and use, as described in the User’s Manual will ensure trouble-free use and prolong the life of your 2.5”... -
Page 4: Getting Started
Getting Started This manual provides installation and assembly instructions for the 2.5” SATA Hard Disk Enclosure. Please review the package contents before installing an HDD or assembling the 2.5” SATA HDD Enclosure. eSATA/USB2.0/FireWire800 Model Rear Panel Package Contents • Enclosure x 1 •... -
Page 5: Installing The 2.5" Sata Hdd
Installing a 2.5” SATA HDD Install a 2.5” SATA HDD in the enclosure by completing the following steps. 1) Remove the screw from the rear panel using a Phillips screwdriver. 2) Carefully remove the rear panel from the enclosure. 3) Carefully slide the bottom panel out of the enclosure housing. Version 02... - Page 6 4) Remove the screw from the control board by loosening the plastic caps. 5) Gently slide the HDD into place. 6) Fasten the HDD to the base using a Phillips screwdriver and the (4) screws included in the package. 7) Align the edges of the HDD platform with the integral rails and carefully slide the assembled platform into the enclosure housing.
- Page 7 8) Ensure that the LED indicator is properly aligned with the opening on the front panel of the enclosure. 9) Reassemble the enclosure by replacing the (2) screws removed in step 1. 10) Fasten the last (1) screw to reattach the bottom panel. 11) Attach the four (4) footpads included in the package to the bottom of the enclosure.
- Page 8 The HDD is now installed and the enclosure is ready for connection to a computer. Version 02...
-
Page 9: Connecting The Enclosure To A Computer
Connecting the Enclosure to a Computer Complete the following steps to connect the enclosure to a host computer. 1) Connect the AC/DC power adapter; ensure that the green LED indicator is active. The LED indicator will blink during data transfer. 2) Insert the eSATA, USB, IEEE 1394a or IEEE 1394b connector into the corresponding port. - Page 10 The DuoLink 2-in-1 eSATA/USB connector combines eSATA and USB 2.0 connectivity in a single port. The DuoLink accommodates both USB and eSATA connectors. To transfer data via USB, connect a USB cable to the enclosure. To transfer data via eSATA connect an eSATA cable to the enclosure. eSATA cable USB cable 3) Insert the eSATA, USB, IEEE 1394a or IEEE 1394b connector into an...
- Page 11 Notes: • Any cable (eSATA, FireWire, or USB 2.0) inserted before the enclosure is powered on has priority over the other cables and will be the primary connection method, i.e.: If the enclosure is connected via FireWire 800 before powering on the enclosure, data will be transferred via FireWire800.
-
Page 12: Notices And Classifications
Notices and Classifications FCC-B Radio Frequency Interference Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.