Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Javes XPL-520
Summary of Contents for Javes XPL-520
- Page 1 Multi-Media LCD Projector User Manual XPL-520...
- Page 2 Thank you for buying our product. Warnings: Please read this specification carefully so that you can understand and use the projector correctly. After reading it, please conserve this specification for next using. Notice: The specifications are subject to change without any notice. The manufacturer of this product will not take the responsibility for the written mistake of the specifications.
- Page 3 You will not be allowed to turn off the projector if the projector works less than 3 minutes, otherwise, the lifetime of lamp will be shorten, and may be bring some troubles to next using. The internal of projector has high voltage, strictly prohibit touching this part. Turn off the power will be allowed when you make sure that the projector was turned off about 5 minutes and the projector was cool.
-
Page 4: Table Of Contents
Content Chapter 1 Preparation Section 1 Setting ……………………………………………...4 Section 2 Connecting of the Signal………………………….4 Section 3 Control Buttons…………….………………………5 Section 4 Using the Remote Control………………………..6 Chapter 2 Basic Operations Section 1 Turning on the Power …………….………………6 Section 2 Turning off the Power ………………….…………7 Section 3 Adjusting the Picture of the Projector……..…….7 Section 4... -
Page 5: Section 1 Setting
Chapter 1 Preparation Section 1 Setting Setting There are two methods to project this projector, please choose the best method base on the condition of the place. 1. Project front: Keep in line or put it a little up then project to the screen 2. -
Page 6: Section 3 Control Buttons
Please turn off the power of the projector and the signal before connecting, may be it will bring troubles if connecting under the condition of power turning on. Please confirm whether the plug of line is fit to the input connecting of the projector, the projector will be mangled if insert the plus with different figure and different pins. -
Page 7: Section 4 Using The Remote Control
○ 2 Menu Button: All the functions and sub-menu will appear ○ 3 Volume Adjust Button/Operate the item ○ 4 INPUT Button: All of modes will appear ○ 5 STANDBY/ON Button: Power off/on Section 4 Using the Remote Control Remote control show below as the picture: MUTE POWER DIGIT... -
Page 8: Section 2 Turning Off The Power
2. Connect the computer or signal with projector. 3. Lift down the lens cover. 4. Connect the power electrical outlet with projector by using the power cable. 5. Turn on the power of equipment, which is connected with the projector. If the operation is prerequisite to make the signal work, please set it to normal working. -
Page 9: Adjusting The Quality Of The Picture
suspender of projector. When setting projector’s position, to make sure decrease distortion, please put the projector to the place of vertical line of screen as close as you can. Aberrances of projector and vertical line of screen are more than 30 degree may cause distortion. - Page 10 Picture Picturemode Normal Brightness Contrast Color Sharpness Move Select Menu to exit 2. Display Use the buttons ←/→ to select an item to operate, and then press ↑/↓ to operate. Display Language English Transparency Factory Reset Scaling 16:9 V Flip H Flip Focus Move...
- Page 11 Channel Auto Searth Manual Searth Skip Fine Tune 60.65 Sound Mode Color Mode PAL60 Channel Edit Move Select Menu to exit 4. VGA(with VGA input) Use the buttons ←/→ to select an item to operate, and then press ↑/↓ to operate. Image Position Select Menu to exit...
-
Page 12: Section 1 Trouble Shooting
Chapter 4 Appendix Section 1 Trouble Shooting 1. Projector do not project (power off) Take off lens cap or not. Connect power immediately after cut off the power. After cut off the power, when cooling, projector cannot be operated immediately; the operation is working after it gets cool (about five minutes). - Page 13 The choosing of resolution is correct or not. Please keep setting of computer output signal and projector’s consistent. We suggest that you set resolution and frequency to 800×600 and 60HZ. 5. Picture’s color badness The connection of signal line is correct or not. The adjusting of picture’s brightness and contrast ratio is correct or not.
-
Page 14: Section 2 Maintenance
Power Light Content Bright red Power on and is on working No image, no signal, need switch the signal. Alarm signal (indicate it will be power off), turn off after power off. Turn on it when it gets cool. Green It is on working Press “power”... -
Page 15: Section 3 Specifications
meet these problems. The lamp burn out, but other parts are normal. The image become darker or unclearly. Note: If above phenomenon has occurred, we suggest you replace the old lamp as soon as possible. We also suggest you prepare the lamp for reserving and purchase the lamp from our dealer. - Page 16 Contrast 500:1 Brightness 1500 Lumens Color Palette 16.7 Million Speaker 8Ω×5W×2 Noise 35dB AC 200V-240/50-60HZ, 2A Power Supply or AC 90V-240/50-60HZ, 2A Power Consumption 225W±10% Temperature Range 5℃-35℃ Size 430mm(L)x340mm(W )x187mm(H) Weight 3.3±0.2Kg Audio Input AUDIO……RCA Faucet×4 RGB×1(15 D-sub port) Video Input VIDEO×1,S-VIDEO×1 TV Input(optional)