Page 2
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. See instruction manual for proper installation and maintenance. DO NOT position system near trampolines, diving boards, slides or any play area equipment.
• Climate, corrosion and excessive use or misuse could result in system failure. • Check tank regularly for leakage. Slow leaks could cause system to tip over unexpectedly. • If technical assistance is required, contact Huffy Customer Service Center. • Adult supervision is recommended when adjusting system.
Page 4
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
Page 5
Get to know the basic parts of your basketball system... FRONT BACKBOARD STRUTS POLE BASE WHEEL CARRIAGE ASSEMBLY 04/03 P/N 211984A...
Page 6
Item Qty. Part No. 206740 200628 226401 900220 201190 986102 202822 202820 200627 203063 201625 203218 986206 203220 200439 203156 203100 12* 201219 900207 203309 203113 203231 203435 201568 203124 201189 201651 * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. P/N 211984A 04/03 PARTS LIST - (See Hardware Identifier)
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) 9/16” and 1/2” Item #10 (1) Item #7 (1) AND/OR Item #8 (1) Item #12 (6)
Page 9
Remove contents from tank IMPORTANT! Center the alignment slot of bottom pole section (6) in the lower hole of top pole section (4) as shown. While maintaining alignment, bounce top section of pole (4) and bottom section (6) together as shown until they no longer move toward taped reference mark.
Page 10
Install rod (5) through holes in bottom pole section (4) and eyebolt (6). Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (29) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown, a deep socket is recommended.
Page 11
Secure tank struts (13) to pole. Rotate non-secured ends of tank struts (13) outward to mounting holes in tank as shown. WARNING! TIGHTEN BOLT (9) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. Secure non-secured ends of tank struts (13) to tank as shown.
Page 12
SECTION B: ASSEMBLE THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION 1/2” Item #22 (4) Item #17 (6) Item #19 (12)* Item #21 (4) Item #23 (2) 1/2”...
Page 13
Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 9. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. While still in the horizontal position, carefully slide backboard components onto pole.
Page 14
Install clips. WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. P/N 211984A 04/03 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm”...
Page 15
NET INSTALLATION SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP 04/03 P/N 211984A...
SECTION C: SECURING THE SYSTEM Place assembled unit to desired location. Fill tank with water (30 gallons (114 liters)) or sand (360 lb. (163 kg)) and snap tank cap (28) in place. Insert T-strap (26) through slot on back of base as shown. Secure unit to ground by twisting tie down stake (27) into ground and hooking T-strap (26) onto tie down stake (27).
Page 17
SECTION E: APPLY HEIGHT AND MOVING LABEL Apply Height and Moving label on pole as shown. MOVING SYSTEM 1. While holding pole, rotate 2. Move basketball system to 3. Carefully rotate basketball 4. Reattach ground restraint and WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT.