Page 1 TOWN & COUNTRY 2009 OWNER’S MANUAL...
Page 2 With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler LLC shall be deemed to be deleted and the features and equipment that are either standard or op- name Chrysler Canada Inc. used in substitution therefor.
Page 3: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 5: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL This Owner’s Manual has been prepared with the assis- Consult the Table of Contents to determine which section tance of service and engineering specialists to acquaint contains the information you desire. you with the operation and maintenance of your vehicle. The detailed Index at the back of this Owner’s Manual It is supplemented by a Warranty Information Booklet contains a complete listing of all subjects.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Remote Starting System — If Equipped ..28 Wireless Ignition Node (WIN) .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door ..... . . 42 Enhanced Seat Belt Use Reminder System (BeltAlert ) .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Rear Seat Delete Feature (Commercial Vehicles Safety Tips ......94 Only) —...
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up.
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a Valet Key, which stores in the rear of the RKE transmitter.
Page 16 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tip Start Feature WARNING! 1. Do not press the accelerator pedal during this process. NEVER leave children alone in a vehicle. Leaving 2. Insert the integrated ignition key into the ignition unattended children in a vehicle is dangerous for a switch.
Page 17: Sentry Key Immobilizer System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder the vehicle. The system will shut the engine off in two If you open the driver’s door with the integrated ignition seconds if an invalid RKE transmitter is used to start the key in the ignition, a chime will sound to remind you to engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: the vehicle. Once an RKE transmitter is programmed to a The Sentry Key Immobilizer system is not compatible vehicle, it cannot be reprogrammed to any other vehicle. with aftermarket remote starting systems. Use of these CAUTION! systems may result in vehicle starting problems and loss of security protection.
Page 19 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key Immobilizer Security Light will begin to flash. Turn the ignition switch system serviced, bring all vehicle RKE transmitters with to the LOCK position and remove the second key. you to the authorized dealer.
Page 20: Vehicle Security Alarm System - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized VEHICLE SECURITY ALARM SYSTEM — IF dealer to have all remaining keys erased from the sys- EQUIPPED tem’s memory. This will prevent the lost key from The Vehicle Security Alarm system monitors the vehicle starting your vehicle.
Page 21 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Arming The System NOTE: Remove the key from the ignition switch and either press The driver’s door key cylinder and the liftgate button a power door lock switch while the driver or passenger on the RKE transmitter cannot arm or disarm the door is open, or press the LOCK button on the Remote system.
Page 22: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Alarm system is armed and the ILLUMINATED ENTRY SYSTEM — IF EQUIPPED battery becomes disconnected, the system will remain The courtesy lights will turn on when you use the armed when the battery is reconnected;...
Page 23: Remote Keyless Entry (Rke) - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) — IF Using the RKE Transmitter EQUIPPED Three-button RKE transmitters will provide basic UN- This system allows you to lock or unlock the doors and LOCK, LOCK and PANIC functions. liftgate, and activate the Panic Alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to about 23 ft (7 m) using a...
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seven-button RKE transmitters will provide functions Remote Unlock Doors and Liftgate that allow the same basic operation as the three-button, Press and release the UNLOCK button on the RKE but may also be used to operate the power liftgate transmitter once to unlock the driver’s door or twice to (optional), power sliding doors, Remote Start feature unlock all doors and liftgate.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 For vehicles not equipped with the EVIC, the Remote Express Down Window Feature Unlock feature can be enabled or disabled by perform- This feature allows you to remotely lower both front door ing the following steps: windows at the same time.
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. While the LOCK button is pressed (after five seconds) NOTE: When you turn off the Panic Alarm by pressing press the PANIC button. Release both buttons. the PANIC button a second time, you may have to be closer to the vehicle due to the Radio Frequency (RF) The Sound Horn with Remote Key Lock feature can be noises of the system.
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The power liftgate may also be opened and closed by Power Right Power Sliding Door. If the button on the pressing the LIFTGATE button located on the overhead RKE transmitter is pushed while the door is being console.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Flash Lights with Remote Key Lock feature can be Programming Additional RKE Transmitters reactivated by repeating the above steps or by perform- Refer to Sentry Key Immobilizer System “Customer Key ing the steps in Section 4, “Electronic Vehicle Information Programming.”...
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 1. Battery access is through a door located on the back of 2. Remove and replace the battery. Avoid touching the the RKE transmitter. Insert a small, flat-bladed screw- new battery with your fingers. Skin oils may cause driver into the slot and gently pry open the access door.
Page 30: Remote Starting System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your RKE transmitter fails to operate from a normal How to Use Remote Start distance, check for these two conditions. All of the following conditions must be met before the engine will Remote Start: 1.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice within five sec- onds. The parking lights will flash and the horn will sound twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For security, power window and power sunroof op- the doors and disarm the Vehicle Security Alarm (if eration (if equipped) are disabled when the vehicle is equipped). Then, prior to the end of the 15-minute cycle, in the Remote Start mode.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 The hood is opened When to Reset Remote Start The vehicle can be started remotely up to a maximum of The hazard switch is pressed two times. The vehicle is also allowed a maximum of one The shift lever is moved out of PARK failed start, where the Remote Starting sequence was initiated but the engine stopped cranking without start-...
Page 34: Door Locks
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS If the lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not Manual Door Locks inside the vehicle before closing the door. Lock the doors by pushing down on the lock plungers on each door trim panel.
Page 35: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. When leaving the vehicle always remove the key from the ignition switch, and lock your vehicle.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or closing the door will allow the locks to operate. A If you press the power door lock switch while the sliding chime will sound if the key is in the ignition switch and door is open, the sliding door will lock.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 2. Fasten your seat belt. (Fastening the seat belt will The Lock Doors Automatically at 15 mph (24 km/h) cancel any chiming that may confuse you during this feature can be reactivated by repeating the above men- programming procedure.) tioned procedure or by performing the procedure in the EVIC (if equipped), Personal Settings (Customer-...
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Unlock Doors Automatically On Exit feature can be 7. To reactivate this feature, repeat the above steps. enabled or disabled by performing the following proce- 8. If a chime is not heard, the program mode was dure: canceled before the feature could be changed.
Page 39: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 The Remote Power Unlock On First Press feature can be WINDOWS enabled or disabled by performing the following proce- Power Vent Windows — If Equipped dure: Switches on the driver’s door trim panel let the driver 1.
Page 40: Power Windows
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Windows You can control either the front or rear windows using switches located on the driver’s door trim panel. The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Power Window Lockout Switch — If Equipped and locks and unlocks all doors. The switch will operate The driver may lock out all power windows by depressing only when the ignition switch is in the ON or ACC the bar switch just below the power window switches.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Power Window Switch NOTE: Please note that the sliding door windows do Second row passengers may power the sliding door not fully recline, stopping several inches above the window by a single switch on the door handle assembly. window sill.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Auto Up Feature With Anti–Pinch Protection — If Any impact due to rough road conditions may trigger Equipped the auto reverse function unexpectedly during auto- The front Driver switch may be equipped with an Auto closure.
Page 44: Sliding Side Door
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Push the window switch down firmly to the second SLIDING SIDE DOOR detent to open the window completely and continue to The sliding door may be opened from the inside or the hold the switch down for an additional two seconds after outside.
Page 45: Power Sliding Side Door - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 There is a hold-open latch that is activated when the Power Sliding Side Door — If Equipped sliding door is fully opened. This latch will keep your The power sliding door may be opened or closed manu- sliding door open on any incline.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power sliding side door must be unlocked If the inside or outside door handles are used while the before the power sliding door switches will operate. power sliding side door is activated, the power sliding door feature will be canceled.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 If anything obstructs the power sliding side door WARNING! while it is closing or opening, the door will automati- cally reverse to the closed or open position, provided You, or others, could be injured if caught in the path it meets sufficient resistance.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 10 seconds of the final cycle, press the HAZ- To provide a safer environment for small children riding ARD switch. in the rear seats, the sliding door locks may be overrid- den by pressing the ON side of the Master Lock Out 4.
Page 49: Sliding Side Door Child Protection Lock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a Child Protection Door Lock system. NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the Child Protection Door Lock system is en- WARNING! gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the Avoid trapping anyone in the vehicle in a collision. outside door handle, the RKE transmitter, the switches Remember that the sliding doors can only be opened on the overhead console or the switches located on the...
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 To Disengage the Child Protection Door Lock The power sliding side door switches will not operate if the vehicle is in gear or the vehicle speed is above 1. Open the sliding side door. 0 mph (0 km/h).
Page 52: Liftgate
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, depress the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
Page 53: Power Liftgate - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Power Liftgate — If Equipped The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmit- ter. Press the button on the transmitter twice within five seconds, to open the power liftgate.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash to Pushing once will only close the liftgate.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 There are also pinch sensors attached to the side of the (62°C). Be sure to remove any buildup of snow or ice liftgate opening. Light pressure anywhere along these from the liftgate before pressing any of the power strips will cause the liftgate to return to the open liftgate buttons.
Page 56: Storage Bin Safety Warning
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. WARNING! (Continued) However, because the gas pressure drops with tempera- In an accident, serious injury could result if the ture, it may be necessary to assist the props when seat storage bin covers are not properly latched.
Page 57: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Seat Storage Bin Cover Emergency Release Lever NOTE: In the event of an individual being locked inside — If Equipped the storage bin, the storage bin cover can be opened from As a security measure, your vehicle may be built with a inside of the bin by pulling on the glow-in-the-dark lever Storage Bin Cover Emergency Release is built into the attached to the storage bin cover latching mechanism.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE An energy-absorbing steering column and steering NOTE: The front airbags have a multistage inflator wheel design. This allows the airbag to have different rates of inflation that are based on collision severity. Knee bolsters/blockers for front seat occupants Please pay close attention to the information in this Front seat belt retractors incorporate pretensioners to...
Page 59: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 and cause a collision that includes you. This can happen WARNING! far away from home or on your own street. It is extremely dangerous to ride in a cargo area, Research has shown that seat belts save lives, and they inside or outside of a vehicle.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is near the seatback of the WARNING! (Continued) front seats and next to your arm in the rear seats. Grasp Wearing your belt in the wrong place could make the latch plate and pull out the belt.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click”. A belt that is worn under your arm is very danger- ous.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 WARNING! WARNING! A lap belt worn too high can increase the risk of A frayed or torn belt could rip apart in a collision and internal injury in a collision. The belt forces won’t be leave you with no protection.
Page 64: Automatic Locking Retractors (Alr) Mode - If Equipped
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Position the shoulder belt on your chest so that it is As a guide, if you are shorter than average you will comfortable and not resting on your neck. When the belt prefer a lower position, and if you are taller than average is long enough to fit, insert the large latch plate into the you will prefer a higher position.
Page 65: Seat Belt Pretensioners
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 How to Use the Automatic Locking Mode by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, 1. Buckle the combination lap/shoulder belt. including those in child restraints.
Page 66 4. Turn the ignition switch to the OFF position. A single 60 seconds of the ignition switch being turned to the ON chime will sound to signify that you have successfully or START position. Chrysler LLC does not recommend completed the programming. deactivating BeltAlert .
Page 67: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Seat Belts and Pregnant Women WARNING! We recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is Using a seat belt extender when not needed can the best way to keep the baby safe.
Page 68: Airbag System Components
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbags have a multistage inflator design. This Front Passenger Airbag may allow the airbag to have different rates of inflation Front and Side Impact Sensors that are based on collision severity and occupant size. Steering Wheel and Column This vehicle may also be equipped with Supplemental Seat Side Airbag Inflatable Curtains (SABIC) to protect...
Page 69: Front Seat Airbag Features
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Front Seat Airbag Features In addition to the small size, the inflating gases exit The front airbag system has dual-stage driver and front through strategically placed vents, which direct the gas passenger airbags. This system provides output appro- away from the occupant.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag covers may not be obvious in the interior trim; WARNING! (Continued) but they will open to allow airbag deployment. Do not use accessory seat covers or place objects The system includes sensors adjacent to both front and between you and the side airbags;...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 the knee bolsters to provide improved protection for the vehicle with a passenger front airbag. An airbag deploy- driver and front passenger. Side airbags also work with ment can cause severe injury or death to infants in that seat belts to improve occupant protection.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All occupants should wear their lap and shoulder belts WARNING! properly. Relying on the airbags alone could lead to more The driver and front passenger seats should be moved severe injuries in a collision. The airbags work back as far as practical to allow the front airbags room to with your seat belt to restrain you properly.
Page 73: Airbag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Airbag Deployment Sensors and Controls The ORC contains a backup power supply system that will deploy the airbags even if the battery loses power or Occupant Restraint Controller (ORC) it becomes disconnected prior to deployment. The ORC is part of a Federally regulated safety system required for this vehicle.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pressure Sensors WARNING! Pressure Sensors trigger airbag deployment based on door cavity pressure changes. Ignoring the Airbag Warning Light in your instru- ment panel could mean you won’t have the airbags to Rollover Sensors protect you in a collision.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Enhanced Accident Response System NOTE: A frontal collision that is not severe enough to In the event of an impact causing airbag deployment, and need airbag protection will not activate the system. This the vehicle communication network intact, and the does not mean something is wrong with the airbag power intact, the Enhanced Accident Response System...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As the airbags deflate, you may see some smoke-like WARNING! particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag Deployed airbags and seat belt pretensioners cannot inflation.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Maintaining Your Airbag System WARNING! (Continued) Do not attempt to modify any part of your ad- WARNING! vanced airbag system. The airbag may inflate Modifications to any part of the airbag system accidentally or may not function properly if modi- could cause it to fail when you need it.
Page 78: Event Data Recorder (Edr)
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light located on the inside of the fuse block cover for the You will want to have the airbags ready to proper airbag fuses. See your authorized dealer if the inflate for your protection in a collision.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Under certain circumstances, EDR data may not be the vehicle owner or lessee) before accessing the elec- recorded (e.g., loss of battery power). tronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
Page 80: Integrated Child Booster Seat - If Equipped
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Used in defense of litigation involving the manufac- Brake status (service and parking brakes) turers product. Accelerator status (including vehicle speed) 3. Requested by police under a legal warrant. Engine control status (including engine speed) 4.
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 The booster seat is designed to raise the child high To position a child into the Integrated Child Booster Seat enough to use the vehicle lap and shoulder belt. The follow these steps: booster seat latch release handle is located at the front of 1.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Place the child upright in the seat with their back firmly against the seatback. 3. Grasp the latch plate and pull out the seat belt. 4. Slide the latch plate up the webbing as far as necessary to allow the seat belt to go around the child’s lap.
Page 83: Integrated Child Seat - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Integrated Child Seat — If Equipped To obtain Integrated Child Seat replacement instruc- Operating instructions for the second row bench seat tions: Refer to the Publication order forms at the back of with Integrated Child Seat are included with the seat.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety experts recommend that children ride WARNING! rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types In a collision, an unrestrained child, even a tiny baby, of child restraints can be used rearward-facing: infant can become a missile inside the vehicle.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Older Children and Child Restraints WARNING! Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the Rearward-facing child seats must NEVER be used in vehicle.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats NOTE: additional information, refer Children who are large enough to wear the shoulder belt www.seatcheck.org or call 1-866-SEATCHECK. comfortably, and whose legs are long enough to bend WARNING! over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat.
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Carefully follow the instructions that come with the WARNING! (Continued) restraint. If you install the restraint improperly, it may Occupants riding in Swivel ’n Go seating must be not work when you need it. wearing their seat belt and the seat must be locked The passenger seat belts are equipped with cinching in either the forward or rearward position.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the When your child restraint is not in use, secure it in the lap/shoulder belt on the child restraint because the vehicle with the seat belt or remove it from the vehicle. buckle or latch plate is too close to the belt path Don’t leave it loose in the vehicle.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 LATCH Anchorages Rear Seat Tether Strap Mounting When using the tether anchorages in the outboard seat- When using the tether anchorages in the center position ing positions, ensure that the strap is routed underneath on third row fold-in-floor seating, ensure that the strap is the head restraint and over the seatback.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WARNING! When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not An incorrectly anchored tether strap could lead to being used for occupant restraints are stowed and out increased head motion and possible injury to the of reach of children.
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Installing the Child Restraint Using the Vehicle To install a child restraint, pull enough of the seat belt Seat Belts webbing from the retractor to route it through the belt Because the lower anchorages are to be introduced to path of the child restraint and slide the latch plate into the passenger carrying vehicles over a period of years, child buckle.
Page 92: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In general, you will first loosen the adjusters on the lower Transporting Pets straps and tether straps so that you can more easily attach Airbags deploying in the front seat could harm your pet. the hook or connector to the lower anchorages and tether An unrestrained pet could be thrown about and possibly anchorages.
Page 93: Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 This vehicle is equipped with a child restraint tether WARNING! anchor located on the lower rear of the front passenger seat. Use this tether anchor to secure only forward- NEVER carry a child in a rear facing infant carrier in facing child restraints equipped with an upper tether a vehicle without rear seats.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The rearward-facing infant carrier is for babies weigh- Children more than 40 lbs (18 kg) should be secured in ing up to about 20 lbs (9 kg), and less than one year the passenger seat in a child restraint or belt- old.
Page 95: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 3. Route the tether strap under the head rest. WARNING! NOTE: Ensure that the child restraint tether strap is The vehicle tether anchor is designed to be used with centered between the headrest supports underneath the a child restraint only.
Page 96: Safety Tips
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the SAFETY TIPS limits of local traffic laws, contributes to a good break-in. Safety Checks You Should Make Inside the Wide-open throttle acceleration in low gear can be detri- Vehicle mental and should be avoided.
Page 97: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Airbag Warning Light Periodic Safety Checks You Should Make Outside The light should come on and remain on for four seconds the Vehicle as a bulb check when the ignition switch is first turned Tires ON.
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Do not run the engine in a closed garage or in confined Check area under vehicle after overnight parking for fuel, areas any longer than needed to move your vehicle in or engine coolant, oil or other fluid leaks.
Page 99: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......102 Tilt Mirrors In Reverse (Available With Memory Seat Only) —...
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Easy Access Seating ....154 UConnect System ....135 Swivel ’n Go Premium Seating —...
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Headlights ......176 Windshield Wipers And Washers ... 182 Automatic Headlights —...
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Backup Camera System — If Equipped . . . 196 Cupholders ......213 Overhead Consoles .
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Cargo Area Storage ....221 Umbrella Holder ..... . 228 Console Features .
Page 104: Mirrors
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 105: Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Automatic Dimming Mirror — If Equipped CAUTION! When using this feature the mirror will automatically adjust for headlight glare from vehicles behind you. You To avoid damage to the mirror during cleaning, never can turn the feature on or off by pressing the button at the spray any cleaning solution directly onto the mirror.
Page 106: Driver's Auto-Dimming Sideview Mirror - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror Folding Feature WARNING! All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have Vehicles and other objects seen in an outside convex three detent positions;...
Page 107: Heated Power Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Driver’s power mirror preselected positions can be con- trolled by the optional Driver Memory Seat Feature. Refer to “Driver Memory Seat” in Section 3. Heated Power Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost.
Page 108: Illuminated Vanity Mirrors - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when the vehicle is shifted out of Reverse position. Each stored memory setting will have an associated Tilt Mir- rors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not en- abled when delivered from the factory.
Page 109: Blind Spot Monitoring - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Blind Spot Monitoring — If Equipped When the vehicle is started, the BSM warning light will The Blind Spot Monitoring (BSM) system uses two radar- be momentarily illuminated in both outside rear view based sensors, located inside the rear bumper fascia, to mirrors to let the driver know that the system is opera- detect Highway licensable vehicles (automobiles, trucks,...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 The BSM system notifies the driver of objects in the The BSM system can also be configured to sound an detection zones by illuminating the BSM warning light audible (chime) alert and mute the radio to notify the located in the outside mirrors.
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate.
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in berms, etc.
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the sensors are blocked by other structures or vehicles, the Electronic Vehicle Information Center (EVIC).
Page 117: Hands-Free Communication (Uconnect ) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 signal is then activated, and it corresponds to an alert Blind Spot Alert Off present on that side of the vehicle, an audible chime will When the BSM system is turned off there will be no also be sounded.
Page 118 UConnect system. The UConnect system allows up to seven cellular phones to be linked to the www.chrysler.com/uconnect system. Only one linked (or paired) cellular phone can be www.dodge.com/uconnect used with the system at a time. The system is available in English, Spanish, or French languages.
Page 119: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Phone Button The UConnect system is fully integrated with the vehi- The rearview mirror contains the microphone cle’s audio system. The volume of the UConnect system for the system (depending on the type of can be adjusted either from the radio volume control mirror and radio equipped), and either the knob or from the steering wheel radio control (right...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For certain operations, compound commands can be Help Command used. For example, instead of saying Setup and then If you need assistance at any prompt, or if you want to Phone Pairing, the following compound command know your options at any prompt, say Help following can be said: Setup Phone Pairing.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To complete the pairing process, you will need to refer- For identification purposes, you will be prompted to ence your cellular phone Owner’s Manual. The give the UConnect system a name for your cellular UConnect website may also provide detailed instruc- phone.
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number The system will prompt you to say the name of the person you want to call. Press the PHONE button to begin. After the Ready prompt and the following beep, say After the Ready prompt and the following beep, say the name of the person you want to call.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 After the Ready prompt and the following beep, say The UConnect system will allow you to enter up to 32 Phonebook New Entry. names in the phonebook with each name having up to four associated phone numbers and designations.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic download and update, if supported, begins This downloaded phonebook cannot be edited or as soon as the phone Bluetooth wireless connection is deleted on the UConnect . These can only be edited on made to the UConnect .
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Some phones cannot send phonebook entries if they Press the PHONE button to begin. are already connected to any system via Bluetooth , After the Ready prompt and the following beep, say and you may see a message on the phone display that Phonebook Edit.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile and a home number, but you can add ”John from the list, press the “Voice Recognition” button Doe’s” work number later using the Phonebook Edit while the UConnect system is playing the desired feature.
Page 127: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 The UConnect system will ask you to verify that you To call one of the names in the list, press the “Voice wish to delete all the entries from the phonebook. Recognition” button during the playing of the desired name, and say Call.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call call when another call is in progress. Therefore, the user Currently in Progress can only answer an incoming call or ignore it. When you receive a call on your cellular phone, the Making a Second Call While Current Call in UConnect system will interrupt the vehicle audio sys- Progress...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Toggling Between Calls has established, press and hold the PHONE button until If two calls are in progress (one active and one on hold), you hear a double beep, indicating that the two calls have press the PHONE button until you hear a single beep, been joined into one conference call.
Page 130: Uconnect System Features
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: This may not be the last number dialed from the An active call is automatically transferred to the UConnect system. mobile phone after the ignition key is switched to OFF. Call Continuation UConnect System Features Call continuation is the progression of a phone call on the Language Selection...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: After every UConnect language change opera- the paired cellular phone to call the emergency num- tion, only the language-specific 32-name phonebook is ber. This feature is supported in the U.S., Canada, and usable.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If supported, this number may be programmable on WARNING! some systems. To do this, press ‘Phone’ button and say ‘Setup’, followed by ‘Towing Assistance’. Your phone must be turned on and paired to the UConnect system to allow use of this vehicle feature in Paging emergency situations, when the cell phone has network...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 You can use your UConnect system to access a voice You can also send stored UConnect phonebook entries mail system or an automated service, such as a paging as tones for fast and easy access to voice mail and pager service or automated customer service line.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts Phone and Network Status Indicators The “Voice Recognition” button can be used when you If available on the radio and/or on a premium display wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by recognition command immediately.
Page 135: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: Certain brands of mobile phones do not send the Advanced Phone Connectivity dial ring to the UConnect system to play it on the Transfer Call to and from Cellular Phone vehicle audio system, so you will not hear it. Under this The UConnect system allows ongoing calls to be trans- situation, after successfully dialing a number the user ferred from your cellular phone to the UConnect system...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List Paired Cellular Phone Names Select Another Cellular Phone This feature allows you to select and start using another Press the PHONE button to begin. phone paired with the UConnect system. After the “Ready” prompt and the following beep, say Press the PHONE button to begin.
Page 137: Things You Should Know About Your Uconnect System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Delete UConnect Paired Cellular Phones Voice Training For users experiencing difficulty with the system recog- Press the PHONE button to begin. nizing their voice commands or numbers, the UConnect After the Ready prompt and the following beep, say system Voice Training feature may be used.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This procedure may be repeated with a new user. The low-to-medium blower setting, system will adapt to the last trained voice only. low-to-medium vehicle speed, To restore the Voice Recognition system to factory default low road noise, settings, enter the Voice Training session via the above procedure and follow the prompts.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 It is not recommended to store similar sounding low-to-medium vehicle speed, names in the UConnect phonebook. low road noise, Phonebook (Downloaded and UConnect Local) name smooth road surface, recognition rate is optimized when the entries are not similar.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth Communication Link Power-Up Cellular phones have been found to lose connection to After switching the ignition key from OFF to either ON the UConnect system. When this happens, the connec- or ACC position, or after a language change, you must tion can generally be re-established by switching the wait at least five seconds prior to using the system.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139...
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141...
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 146: General Information
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information SEATS This device complies with Part 15 of the FCC rules and Seats are a primary part of the Occupant Restraint RSS 210 of Industry Canada. Operation is subject to the (protection) System of the vehicle.
Page 147: Manual Front And Second Row Seat Adjuster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Manual Front And Second Row Seat Adjuster Using body pressure, move forward and rearward on the The adjusting bar is located under the front of the seat. seat to be sure the seat adjusters have latched. Pull the bar upward and move the seat to the desired WARNING! position.
Page 148: Eight-Way Driver And Passenger Power Seat - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight–Way Driver And Passenger Power Seat — If Equipped The power seat switches are located on the outboard side of the seat. The front switch controls the up/down, forward/rearward and tilt adjustment. The rear switch controls the recline adjustment of the seatback.
Page 149: Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 150: Heated Seats - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for front heated seats are located on the center instrument panel area. The switch indicator lights will show when the High or Low heat is on. Press the switch once to choose High (two lights), press it a second time to choose Low (one light), press it a third...
Page 151: Manual Reclining Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 its normal position. Using body pressure, lean forward WARNING! and rearward on the seat to be sure the seatback has latched. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 152: Manual Lumbar Adjust Lever - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 153: Stow 'N Go Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Stow ’n Go Seating — If Equipped On vehicles equipped with Stow ’n Go seating, the second and third row seats may be folded into the floor for convenient storage. To Fold Second Row Seats 1.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pull up on the seatback recliner lever located on the 5. Pull rearward on the release strap located at the rear of outboard side of the seat and fold the seatback down. To the seat and tumble the seat forward into the storage bin.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To Unfold Second Row Seats CAUTION! 1. Pull up on the storage bin latch to open the cover. The storage bin cover must be locked and flat to 2. Pull up on the handle to lift the seat out of the storage avoid damage from contact with the front seat tracks, bin and push the seat rearward to latch the seat anchors.
Page 156: Easy Access Seating
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull upward on the seatback recliner lever, located on 4. Adjust the head restraint to the desired position, close the outboard side of the seat, to return the seatback to its the storage bin cover and slide the storage bin locking full upright position.
Page 157: Swivel 'N Go Premium Seating - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 To return the seat to its upright position, push rearward WARNING! on the seatback until it latches. Always ensure that it is fully latched. In the event of a collision you could be injured if the seat is not fully latched.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats are removable rotation. Once the seat begins to rotate, the handle may be released. The seat locks in position once reaching the forward or rearward positions only. Swivel ’n Go Seating Features 1 —...
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! WARNING! (Continued) Occupants riding in Swivel ’n Go seating must be Failure to comply with the following conditions wearing their seat belt and the seat must be locked could result in serious injury or even death. in either the forward-facing or rearward-facing NEVER place any child seat or infant carrier in the position.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull up on the release bar located at the bottom front 4. Remove the seat from vehicle through the liftgate. edge of the swivel seat. Rollers are part of the seat frame and will ease the removal process.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Swivel ’n Go Premium Seating Table — If 1. Open the floor storage cover in front of the second row Equipped seats. The Swivel ’n Go Seating Table consists of an easily assembled post and top. Table and Leg Storage 2.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Insert pole into base by aligning the lock button into NOTE: You will hear an audible “click” when the lock notch of the base. button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top.
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! (Continued) DO NOT place liquid drinks on the table, use available cupholders. Second row seats must be locked in the rearward facing position before installing the table. To separate the table top from the pole, follow these steps: 1.
Page 164: Second Row Bench Seat - If Equipped
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The table top should be removed from the leg Plastic Grocery Bag Retainer Hooks prior to removing the leg from its mounting base. Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and 4.
Page 165: Third Row Power Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 WARNING! If not properly latched, the bench seats could become loose. Personal injuries could result. After reinstall- ing these seats, be sure the red indicator button on the release handles return into the handles. Third Row Power Seat —...
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power recline feature, located on the side of the seat Third Row Power Seat Switch — If Equipped cushion, adjusts the seatback angle forward/rearward A one-touch power folding seat switch is located in the for occupant comfort.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together. The third row power folding seat adjusts to the following positions using the switch bank located on the left rear trim panel: Rear Panel Power Switch Bank...
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The third row power seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion for a brief period. Should this occur, remove the obstacle and press the button again, for the desired position.
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To Unfold Third Row Seats Tailgate Mode 1. Pull up on the assist strap to lift the seat out of the 1. Pull release strap “2”, then pull release strap “3” to storage bin and push the seat forward until the anchors rotate the entire seat rearward.
Page 170: Driver Memory Seat System - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. DRIVER MEMORY SEAT SYSTEM — IF EQUIPPED Once programmed the Memory Buttons 1 and 2 on the driver’s door panel can be programmed to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator pedals, and radio station preset settings.
Page 171: Setting Memory Positions And Linking Rke
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Setting Memory Positions And Linking RKE 5. Turn on the radio and set the radio station presets (up Transmitter To Memory to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered 6.
Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 11. Select Remote Linked to Memory in the Electronic A recall can be cancelled by pressing any of the memory Vehicle Information Center (EVIC). Refer to the “Customer- buttons on the driver’s door during a recall (S, 1, or 2). Programmable Features”...
Page 173: Easy Entry/Exit Seat (Available With Memory Seat Only)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 4. Within five seconds, press and release Memory button Easy Entry/Exit Seat (Available with Memory Seat 1 on the driver’s door. A chime will sound signaling to ONLY) you that the driver memory has been set. This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the 5.
Page 174: To Open And Close The Hood
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE between 0.9 – 2.7 in (22.7 – 67.7 mm) forward of the TO OPEN AND CLOSE THE HOOD rear stop. The seat will return to its previously set To open the hood, two latches must be released. position when you insert the key into the ignition 1.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 2. Move to the front of the vehicle and look inside the Use the hood prop rod to secure the hood in the open center of the hood opening. Locate, then push the safety position.
Page 176: Lights
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lighting All of the lights, except the Hazard warning lights, Interior lights are turned on when a door or liftgate is headlight high beams and flash-to-pass, are controlled by opened, the Remote Keyless Entry (RKE) transmitter is switches to the left of the steering column on the instru- activated, or when the dimmer control is moved to the ment panel.
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Dome Light Positions Parade Mode (Daytime Brightness Feature) Rotate the dimmer control completely Rotate the dimmer control to the first upward to the second detent (extreme detent. This feature brightens the top position) to turn on the interior odometer, radio and overhead dis- lights, except the front reading/ plays when the parking lights or head-...
Page 178: Parking Lights
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Halo Lights — If Equipped To change the brightness of the instrument panel lights, Halo lights are strategically placed soft lighting that help rotate the dimmer control up or down. to illuminate specific areas to aid the occupants in Automatic Headlights —...
Page 179: Headlights On With Wipers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 on when windshield wipers are on may be found on vehicles equipped with an automatic headlight system. Refer to the Electronic Vehicle Information Center (EVIC) in Section 4 under “Personal Settings (Customer- Programmable Features)” for more information. Headlight Delay —...
Page 180: Daytime Running Lights (Canada/Fleet Vehicles Only)
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The headlight delay time is programmable on vehicles Daytime Running Lights (Canada/Fleet Vehicles equipped with an EVIC. Refer to “Delay Turning Head- Only) lights Off,” under “Personal Settings (Customer- The headlights on your vehicle will illuminate when the Programmable Features)”...
Page 181: Battery Protection
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Battery Protection Multifunction Lever This feature provides battery protection to avoid wearing The multifunction lever is located on the left side of the down the battery if the headlights, parking lights, or steering column. front fog lights are left on for extended periods of time The multifunction lever controls the: when the ignition switch is in the LOCK position.
Page 182: Turn Signals
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals If either indicator flashes at a rapid rate, check for a Move the multifunction lever up or down to signal either defective outside turn signal light bulb. If one of the a right or left turn.
Page 183: High Beam/Low Beam Select Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 High Beam/Low Beam Select Switch To Activate When the headlights are turned on, pushing the multi- 1. Select “Automatic High Beams — ON” through the function lever toward the instrument panel will switch EVIC.
Page 184: Windshield Wipers And Washers
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull the multifunction lever toward you to switch the off position. If the windshield wiper switch is turned off headlights from the high beam to the low beam position. and the blades cannot return to the off position, damage to the wiper motor may occur.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 1. Mist, Front Wiper and Washer 2. Intermittent, Low and High Speed Wipers Press the end of the multifunction lever inward to the Use the intermittent wipers when weather conditions first detent and release to clear the windshield. Pressing make a single wiping cycle, with a variable pause be- the multifunction lever inward to the second detent will tween cycles, desirable.
Page 186: Rain Sensing Wipers - If Equipped
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Rear Wiper and Washer Rain Sensing Wipers — If Equipped Rotating the rotary ring to the first detent activates the This feature senses moisture on the windshield and rear intermittent wipers. To activate the washers, rotate automatically activates the wipers for the driver.
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: Low Temperature Wipe Inhibit — The rain sensing The rain sensing feature will not operate when the feature will not operate when the ignition is first wiper speed is in the Low or High position. switched ON, and the vehicle is stationary, and the outside temperature is below 32°F (0°C), unless the The rain sensing feature may not function properly...
Page 188: Tilt Steering Column - If Equipped
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the lever downward (located on the steering column and below the steering wheel) to the open position. You may then position the steering wheel up or down, as desired.
Page 189: Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward, or away, from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat positions.
Page 190: Electronic Speed Control - If Equipped
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The pedals can be adjusted while driving. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over the The pedals cannot be adjusted when the vehicle is in accelerator operation at speeds greater than 25 mph REVERSE or when the Electronic Speed Control Sys- (40 km/h).
Page 191: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 To Activate To Set At A Desired Speed Push the ON/OFF button (located in the end of the lever) When the vehicle has reached the desired speed, press once, and the cruise indicator light (located in the mes- the SET lever downward and then release.
Page 192: Varying The Speed Setting
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Varying The Speed Setting NOTE: In order to ensure proper operation the Elec- When the Electronic Speed Control is SET, speed can be tronic Speed Control system has been designed to shut increased by raising and holding the RESUME/ACCEL down if multiple speed control switch functions are lever upwards.
Page 193: Rear Park Assist System - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 On steep hills, a greater speed loss or gain may occur, so REAR PARK ASSIST SYSTEM — IF EQUIPPED it may be preferable to drive without Electronic Speed The Rear Park Assist system provides visible and audible Control.
Page 194: Rear Park Assist Sensors
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h). Rear Park Assist Sensors The four rear park assist sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’...
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 set to warn of obstacles behind the right rear of the The system dimly illuminates the two innermost yellow vehicle. The vehicle is close to the obstacle when the red LEDs when it is on and detects no obstacles. The follow- LED is illuminated.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) Before using the Rear Park Assist system, it is Drivers must be careful when backing up, even strongly recommended that the ball mount and when using the Rear Park Assist System. Always hitch ball assembly be disconnected from the check carefully behind your vehicle, and be sure to vehicle, when the vehicle is not used for towing.
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: CAUTION! Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. To avoid vehicle damage, the Rear Park Assist system should only be used as a parking aid and is Jackhammers, large trucks, and other vibrations could unable to recognize every obstacle, including affect the performance of the system.
Page 198: Rear Backup Camera System - If Equipped
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With the Compass Mini-Trip Should this wrench symbol display with the Computer (CMTC) letter P next to it, your Park Sense system You can turn the Rear Park Assist system ON or OFF needs servicing.
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 NOTE: The Rear Camera system can be enabled and 5. Backup as necessary. disabled, refer to your Radio/Navigation/Multimedia 6. Place the shift lever in PARK or DRIVE to exit the Rear manual. Backup Camera system. Use the following steps to access the Rear Backup Cam- WARNING! era feature:...
Page 200: Overhead Consoles
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLES CAUTION! Front Overhead Console To avoid vehicle damage the Rear Backup Camera Two versions of the overhead console are available. The System should only be used as a parking aid and base front overhead console model featured fixed incan- is unable to view every obstacle, or object in your descent courtesy/reading lights, flip-down sunglass stor-...
Page 201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry (RKE), the lights will also turn on when the UNLOCK button on the transmitter is pressed. The courtesy lights also function as reading lights.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglass Storage (non-sunroof only) At the rear of the front overhead console, a compartment is provided for the storage of two pairs of sunglasses. Press the door latch to open the compartment. The door will slowly rotate to an open position.
Page 203: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 Rear Courtesy/Reading Lights — If Equipped Rear Console Halo Lighting The overhead console has two sets of courtesy lights. The The rear overhead console has recessed halo lighting lights turn on when a front door, a sliding door or the around the perimeter of the console base.
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons that are located in the headliner WARNING! or sun visor designate the three different HomeLink channels. Your motorized door or gate will open and close while you are training the universal transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 205: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Programming Homelink Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while Before You Begin keeping the indicator light in view. If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After training a HomeLink channel, if the garage This can usually be found where the hanging antenna door does not operate with HomeLink and the ga- wire is attached to the garage door opener motor. It is rage door opener was manufactured after 1995, the NOT the button normally used to open and close the garage door opener may have a rolling code.
Page 207 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 6. Firmly press and release the “Learn” or “Training” Using HomeLink button. The name and color of the button may vary by To operate, simply press and release the programmed manufacturer. HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, NOTE: There are 30 seconds in which to initiate the next security system, entry door lock, home/office lighting,...
Page 208: Gate Operator/Canadian Programming
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming has successfully accepted the frequency signal. The Canadian radio frequency laws require transmitter sig- indicator light will flash slowly and then rapidly when nals to time-out (or quit) after several seconds of trans- fully trained.
Page 209: Troubleshooting Tips
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Troubleshooting Tips 2. This device must accept any interference that may be If you are having trouble programming HomeLink , here received including interference that may cause undesired are some of the most common solutions: operation.
Page 210: Power Sunroof - If Equipped
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof control switch is located in the front overhead console.The sunroof panel tilts upward at the In an accident, there is greater risk of being thrown rear for ventilation or slides rearward under the roof.
Page 211 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 NOTE: The sunshade cannot be closed if the sunroof is Express-Vent open. Press and release the V button, and the sunroof will automatically open to the vent position. This is called WARNING! Express-Vent. Express-Close Never leave children in a vehicle with the key in the Press the switch forward and release, and the sunroof...
Page 212: Electrical Power Outlets - If Equipped
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition OFF Operation open or partially open positions. This is a normal occur- The power sunroof switch will remain active for 10 min- rence and can be minimized. If the buffeting occurs with utes after the ignition switch is turned OFF.
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 The lower outlet is protected by an automatic reset circuit breaker. The automatic circuit breaker restores power when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position.
Page 214: Power Inverter - If Equipped
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED CAUTION! (Continued) A 110-Volt, 150-Watt inverter outlet (if equipped) con- Accessories that draw higher power (i.e., coolers, verts DC current to AC current, and is located on the left vacuum cleaners, lights, etc.), will degrade the rear trim panel immediately behind the second row left battery even more quickly.
Page 215: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 The Power Inverter switch is located near the center of CUPHOLDERS the instrument panel below the two 12-Volt power out- There are nine cupholders in the interior. Two cupholders lets. Press the switch to turn the power on for the outlet, in the center front instrument panel, four in the floor press the switch a second time to turn the power off.
Page 216: Interior Bottle Holders
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel.
Page 217: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 The left rear trim panel cupholder is designed to accom- modate a second ash receiver, if desired. STORAGE Glove Compartments Upper Glove Compartment To open the upper compartment, press inward on the release button (2). The door will spring open about 1 in (2.54 cm).
Page 218: Door Trim Panel Storage
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lower Glove Compartment To open the lower compartment, pull out on the release handle (3). The lower compartment handle is also equipped with a lock (3). Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
Page 219: Driver Seatback Storage - As Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 Sliding Side Door Bottle Holder Driver Seatback Storage — As Equipped Both sliding doors have a bottle holder molded right into The drivers seatback has a primary storage pocket on all the trim. models and an optional secondary mesh pocket.
Page 220: Second Row Floor Storage Bins
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Floor Storage Bins CAUTION! The area below the floor covers, located in front of the second row seats, is available for storage The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 221: Center And Rear Overhead Console Storage - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Center And Rear Overhead Console Storage — If Equipped The overhead storage system comes in several options. Overhead Console Features 1 — DVD 5 — Storage 2 — Rear HVAC 6 — DVD 3 —...
Page 222: Rear Compartment Storage
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Compartment Storage Your vehicle is equipped with open storage areas located in each rear trim panel. Third Row Rear Seat and Rear Compartment Features 1 — Tie Down 5 — Liftgate Close 2 —...
Page 223: Coat Hooks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 224: Console Features
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES There are two consoles available: Basic and Premium. Basic Console Basic Console features consist of the following: The basic console profile allows vehicle occupants to easily pass through the first row to the second. Four cupholders accept up to extra large size beverage cups or 20 oz (.6 L) plastic bottles.
Page 225: Premium Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 To Remove The Basic Floor Console 5. Pull up on the console to be sure it is firmly latched. 1. Remove the front anchor cup plug and clip. WARNING! 2. Slide the console base forward while lifting slightly to In an accident, serious injury could result if the clear the rear load floor hook.
Page 226 224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Upper storage bin can hold nine regular or 18 thin CDs or other items Large console center storage will store headphones for the available rear DVD entertainment system or other items 12-Volt DC power outlet provides continuous power inside the console for cell phones or other electronics.
Page 227 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 holder insert for both cavities can easily be removed for Position 2 shows the raised storage tray revealing a large cleaning. The cupholders will also accommodate large storage area below. size cups and 20 oz (.6 L) bottles. Position 1 shows the console closed with four cupholders and a convenient storage tray.
Page 228 226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dual Storage Bins Position 4 shows the complete console in its rearmost Position 3 shows the top portion of the console in a position. Again, lifting second latch handle at the front of rearward position.
Page 229: Electric Rear Window Defroster - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 To Remove The Premium Floor Console 5. Pull up on the console to be sure it is firmly latched 1. Pull up on the bottom release handle in the front of the WARNING! console In an accident, serious injury could result if the 2.
Page 230: Umbrella Holder
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After the initial time interval has expired, if the rear UMBRELLA HOLDER window defogger switch is pressed to the on position An umbrella holder has been conveniently molded into again (during the same ignition cycle), the system will the left front door entry scuff molding.
Page 231: Load-Leveling System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 LOAD-LEVELING SYSTEM WARNING! The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading Do not install the load-leveling system on vehicles conditions. that are not equipped with Anti-Lock Brakes. Ve- hicles without Anti-Lock Brakes (ABS) have a height- A hydraulic pump contained within the shock absorbers sensing proportioning valve.
Page 232 230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. crossbar should be fastened at the rearmost position of The roof rack does not increase the total load carrying the side rails. This will help reduce the amount of wind capacity of the vehicle.
Page 233 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 CAUTION! (Continued) WARNING! Long loads which extend over the windshield, Cargo must be securely tied before driving your such as wood panels or surfboards, or loads with vehicle. Improperly secured loads can fly off the large frontal area should be secured to both the vehicle, particularly at high speeds, resulting in per- front and rear of the vehicle.
Page 234: Sun Screens - If Equipped
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SUN SCREENS — IF EQUIPPED Gently pull up on the tab to raise the sun screen. Sun screens are available for second and third row Continue pulling the sun screen until the tab is near the seating windows.
Page 235 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 Once the screen is completely to the top of the window, To lower the sun screen, gently lift the tab upward to extend the top bar of the sun screen over the two hooks disengage the hooks, and feed the screen back into the attached to the top of the window.
Page 237: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....239 Compass/Temperature Display ... 256 Instrument Cluster – Base ....240 Electronic Vehicle Information Center (EVIC) —...
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM/CD/DVD Multimedia System Radio Sales Code RES/RSC — AM/FM Stereo Radio (RER/REN) – If Equipped ....270 With CD Player (MP3 AUX Jack) And Sirius Radio.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Play Mode ......295 Operating Instructions — Video Entertainment System (VES)™ List Or Browse Mode .
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL Climate Controls ..... . 308 Winter Operation ..... 325 Manual Heating, Ventilation And Air Vacation/Storage .
Page 241: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 239 INSTRUMENT PANEL FEATURES 1 - Air Vent 5 - Analog Clock 9 - DVD – (If Equipped) 13 - Hazard Switch 2 - Instrument Cluster 6 - Upper Glove Compartment 10 - Cup Holders 14 - Ignition Switch 3 - Shift Lever 7 - Lower Glove Compartment 11 - Storage Bin...
Page 242: Instrument Cluster - Base
240 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – BASE...
Page 243: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 241 INSTRUMENT CLUSTER – PREMIUM...
Page 244: Instrument Cluster Descriptions
242 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS vehicle has completely stopped and the shift lever is placed in the PARK position, the light should turn off. 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when If the light remains lit with the engine running your the ignition switch is in the ON position.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 243 vehicle is experiencing a problem with the charging Accordingly, when the low tire pressure telltale illumi- system. Obtain SERVICE IMMEDIATELY. See an autho- nates, you should stop and check your tires as soon as rized dealer. possible, and inflate them to the proper pressure.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL illuminated. This sequence will continue upon subse- CAUTION! quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- The TPMS has been optimized for the original tem may not be able to detect or signal low tire pressure equipment tires and wheels.
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 245 6. Oil Pressure Warning Light pass H , the indicator will continuously flash and a This light indicates low engine oil pressure. The continuous chime will occur until the engine is allowed light should turn on momentarily when the engine to cool.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle electronics sense that the vehicle has 11. Brake System Warning Light traveled about one mile with the turn signals on, a This light monitors various brake functions, continuous chime will sound to alert you to turn the including brake fluid level and parking brake signals off.
Page 249 UNDERSTANDING YOUR INSTRUMENT PANEL 247 The dual brake system provides a reserve braking capac- WARNING! ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is Driving a vehicle with the red brake light on is indicated by the Brake Warning Light, which will turn on dangerous.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is the conventional brake system will continue to operate applied with the ignition switch in the ON position. normally if the BRAKE warning light is not on. NOTE: This light shows only that the parking brake is If the ABS light is on, the brake system should be serviced applied.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249 15. Tachometer check or when driving, if the driver’s seat belt remains The red segments indicate the maximum permissible unbuckled, the Seat Belt Reminder Light will illuminate engine revolutions per minute (RPM x 1000) for each gear and the chime will sound.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL If the MIL flashes when the engine is running, serious The gauge pointer will likely indicate a higher tempera- conditions may exist that could lead to immediate loss of ture when driving in hot weather, up mountain grades, power or severe catalytic converter damage.
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 251 NOTE: On the Base cluster, the reset button toggles WARNING! between odometer, Trip A, Trip B and outside tempera- ture. To reset a message display on Base Cluster (Change A hot engine cooling system is dangerous. You or Oil Required, gASCAP, gATE, LoCOOL, LoWASH, no- others could be badly burned by steam or boiling FUSE), push and hold the button until the display resets...
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Odometer Display Area Refer to ”Compass Mini-Trip Computer (CMTC) When the appropriate conditions exist, the following Display— If Equipped” / ”Electronic Vehicle Informa- odometer messages will display: tion Center (EVIC) Display — If Equipped” later in this section, for more information.
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 instrument cluster. To reset the oil change indicator correct mileage that the vehicle has been driven. There- system (after performing the scheduled maintenance), fore, if the odometer reading is changed during repair or perform the following steps. replacement, be sure to keep a record of the reading before and after the service, so that the correct mileage 1.
Page 256: Compass Mini-Trip Computer (Cmtc) - If Equipped
254 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Display — If Equipped COMPASS MINI-TRIP COMPUTER (CMTC) — IF The Electronic Vehicle Information Center (EVIC) fea- EQUIPPED tures a driver-interactive display that is located in the NOTE: The compass on your vehicle is self-calibrating, instrument cluster.
Page 257: Cmtc Reset Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 255 gASCAP ..... . . Fuel Cap Fault NE ..Eight-point compass headings are displayed hood .
Page 258: Compass/Temperature Display
256 UNDERSTANDING YOUR INSTRUMENT PANEL Trip A panel. This is where the compass module is located and Shows the total distance traveled for Trip A since the last such devices may interfere and cause false compass reset. readings. Trip B Shows the total distance traveled for Trip B since the last reset.
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257 To Set the Variance 1. Start the engine and leave the transmission in the Start the engine and leave the transmission gear selector PARK position. lever in the PARK position. Press and hold the CMTC 2.
Page 260: Electronic Vehicle Information Center (Evic) - If Equipped
258 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER This system conveniently allows the driver to select a variety of useful information by pressing the switches (EVIC) — IF EQUIPPED mounted on the steering wheel. The EVIC consists of the following: System Status display Vehicle information warning message displays...
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 EVIC Menu / Step Control Button, as Steering Wheel EVIC Compass/Temp it appears on the left side of the steer- Control Button, as it appears on the ing column. right side of the steering column. Press and release the MENU button, and the Press and release the Compass/Temperature mode...
Page 262: Evic Displays
260 UNDERSTANDING YOUR INSTRUMENT PANEL EVIC Displays Left Rear Turn Signal Light Out When the appropriate conditions exist, the EVIC displays Right Front Turn Signal Light Out the following messages: Right Rear Turn Signal Light Out Door(s) Ajar (with a single chime, if vehicle is in motion) Park Assist Disabled Liftgate Ajar (chime will sound when vehicle starts...
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 rear view icons will be illuminated. If electronic inter- indicator system is duty-cycle based, which means the ference is present, the BSM system will illuminate the engine oil change interval may fluctuate dependent upon icon only on the side of interference as long as your personal driving style.
Page 264: Trip Functions
262 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Functions determined by a weighted average of the instantaneous Press and release the MENU button until one of the and average fuel economy, according to the current fuel following Trip Functions displays in the EVIC. tank level.
Page 265: Compass Display
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Display Units of Measure in: Automatic Compass Calibration To make your selection, press and release the STEP This compass is self-calibrating, which eliminates the button until “US” or “METRIC” appears. need to manually reset the compass. When the vehicle is new, the compass may appear erratic and the EVIC will To Reset the Display display CAL until the compass is calibrated.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the STEP button until “Calibrate Compass” is NOTE: Keep magnetic materials away from the top of displayed in the EVIC. the instrument panel, such as IPODs, Cell Phones, Lap- tops and Radar Detectors. This is where the compass 4.
Page 267: Personal Settings (Customer-Programmable Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 265 2. Press and hold the compass button for approximately Use the Step button to display one of the following two seconds. choices. 3. Press the STEP button until “Compass Variance” mes- Language sage, and the last variance zone number, displays in the When in this display you may select one of five lan- EVIC.
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL Auto UNLK On Exit RKE Linked To Memory When ON is selected, all doors will unlock when the When this feature is selected the memory seat, mirror, vehicle is stopped and the transmission is in the PARK or and radio settings will return to the memory set position NEUTRAL position and the driver’s door is opened.
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 Headlamp Off Delay Tilt MIRR. In Reverse When this feature is selected, the driver can choose to When this feature is selected and the vehicle is placed in have the headlights remain on for 0, 30, 60, or 90 seconds a reverse gear, the side mirrors tilt downward to allow when exiting the vehicle.
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL ILLUMIN. Approach NOTE: If your vehicle has experienced any damage in When this feature is selected, the headlights will activate the area where the sensor is located, even if the fascia is and remain on for up to 90 seconds when the doors are not damaged, the sensor may have become misaligned.
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 Door Alert Automatic High Beams — If Equipped When this feature is selected the signal lamps activate When this feature is selected, the high beam headlights when power or manual sliding doors are in operation, will deactivate automatically under certain conditions.
Page 272: Am/Fm/Cd/Dvd Multimedia System Radio (Rer/Ren) - If Equipped
270 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM/CD/DVD MULTIMEDIA SYSTEM RADIO Operating Instructions — Voice Recognition (RER/REN) – IF EQUIPPED System (VR) — If Equipped For the radio, refer to “Voice Recognition System (VR)” in NOTE: The sales code is located on the lower right side Section 3.
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 To Manually Set the Clock — RER/REN 6. To save the new time setting, touch the screen where the word “Save” is displayed. 1. Turn on the multimedia system. Changing Daylight Savings Time 2. Touch the screen where the time is displayed. When selected, this feature will display the time of day in 3.
Page 274 272 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off 2. Touch the screen where the time is displayed. The When selected, this feature will display the time of day clock setting menu will appear on the screen. on the touch screen when the multimedia system is 3.
Page 275: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 273 SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 276 274 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio 4. Adjust the minutes using the right side Tune/Scroll will remain tuned to the new station until you make control knob. Press the Tune/Scroll control knob to save another selection.
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 275 Push the rotary Tune/Scroll control knob a second time AM/FM Button and MID will display. Turn the Tune/Scroll control knob Press the buttons to select either AM or FM mode. to the right or left to increase or decrease the mid-range SET/RND Button —...
Page 278: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
276 UNDERSTANDING YOUR INSTRUMENT PANEL and 12 FM stations to be stored into pushbutton memory. This radio is capable of playing compact discs (CD), The stations stored in SET 2 memory can be selected by recordable compact discs (CD-R), rewritable compact pressing the pushbutton twice.
Page 279 UNDERSTANDING YOUR INSTRUMENT PANEL 277 If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. This CD player will accept 4-3/4 in (12 cm) discs only.
Page 280: Notes On Playing Mp3 Files
278 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Press the RND button a second time to stop Random Press the RW button to stop the CD at the beginning of Play. the current CD track/title. Notes on Playing MP3 Files Press and hold the FF (Fast Forward) button and the CD The radio can play MP3 files;...
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs.
Page 282 280 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rate.
Page 283: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Operation Instructions - Auxiliary Mode SALES CODE RES/RSC — AM/FM STEREO The auxiliary (AUX) jack is an audio input jack, which RADIO WITH CD PLAYER (MP3 AUX JACK) AND allows the user to plug in a portable device, such as an SIRIUS RADIO MP3 player, or cassette player, and utilize the vehicle’s NOTE: The radio sales code is located on the lower right...
Page 284: Operating Instructions - Radio Mode
282 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 Phone Button (UConnect Hands-Free Phone) — If 3. After adjusting the hours, press the right side Tune/ Equipped Scroll control knob to set the minutes. The minutes will Press this button to operate the Hands-Free Phone begin to blink.
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Push the rotary Tune/Scroll control knob a second time Press the INFO button for an RDS station (one with call and MID will display. Turn the Tune/Scroll control knob letters displayed). The radio will return a Radio Text to the right or left to increase or decrease the mid-range message broadcast from an FM station (FM mode only).
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 MUSIC TYPE Button 16-Digit Character Program Type Pressing this button once will turn on the Music Type Display mode for five seconds. Pressing the MUSIC TYPE button Foreign Language Language or turning the Tune/Scroll control knob within five Information Inform seconds will allow the program format type to be se-...
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL Set Clock — Pressing the SELECT button will allow 16-Digit Character Program Type you to set the clock. Turn the Tune/Scroll control knob Display to adjust the hours and then press and turn the Sports Sports Tune/Scroll control knob to adjust the minutes.
Page 289: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 287 You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 291: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 289 the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD, MP3 modes. Random Play.
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) exceeding 20 folders will result in this display. With The medium formats supported by the radio are ISO 9660 200 files, exceeding 50 folders will result in this Level 1 and Level 2 and includes the Joliet extension. display.) When reading discs recorded using formats other than Maximum number of characters in file/folder names:...
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 160, 128, 144, extension may cause playback problems.
Page 294: List Button (Cd Mode For Mp3 Play)
292 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected playing the files contained in that folder (or the next by the following: folder in sequence if the selection does not contain playable files). Media - CD-RW media may take longer to load than CD-R media The folder list will time out after five seconds.
Page 295: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Operation Instructions - Auxiliary Mode Operating Instructions - Hands-Free Phone The auxiliary (AUX) jack is an audio input jack, which (UConnect ) (If Equipped) allows the user to plug in a portable device such as an Refer to “Hands-Free Communication (UConnect )”...
Page 296: Connecting The Ipod
294 UNDERSTANDING YOUR INSTRUMENT PANEL UCI supports Mini, 4G, Photo, Nano, 5G iPod system (iPod may take a few seconds to connect), the iPhone devices. Some iPod software versions may not iPod starts charging and is ready for use by pressing fully support the UCI features.
Page 297: Controlling The Ipod Using Radio Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 295 The iPod can be controlled using the radio buttons to Turning it clockwise (forward) by one click, while Play, Browse, and List the iPod contents. playing a track, skips to the next track. The iPod battery charges when plugged into the UCI Turning it counterclockwise (backward) by one connector.
Page 298: List Or Browse Mode
296 UNDERSTANDING YOUR INSTRUMENT PANEL Use the << SEEK and SEEK >> buttons to jump to the current list and then forward to the next song. To stop previous or next track. If the << SEEK button is SCAN mode and start playing the desired track, when pressed during the first two seconds of the track, it will it is playing the track, press the SCAN button again.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 Turning it clockwise (forward) and counterclock- Preset 3 – Albums wise (backward) scrolls through the lists, displaying Preset 4 – Genres the track detail on the radio display. Once you have the track to be played highlighted on the radio Preset 5 - Audiobooks display, press the TUNE control knob to select and Preset 6 –...
Page 300: Satellite Radio - If Equipped (Ren/Req/Rer/Res/Reu Radios Only)
298 UNDERSTANDING YOUR INSTRUMENT PANEL the same steps to go to the desired track in that list. WARNING! Not all iPod sub-menu levels are available on this system. Do not plug in or remove the iPod while driving. Failure to following this warning could result in an MUSIC TYPE button: The MUSIC TYPE button is accident.
Page 301: System Activation
UNDERSTANDING YOUR INSTRUMENT PANEL 299 System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you ESN/SID Access With REQ/RES Radios may begin listening immediately to the one year of audio With the ignition switch in the ON/RUN or ACC posi- service that is included with the factory-installed satellite tion and the radio on, press the SETUP button and scroll radio system in your vehicle.
Page 302: Selecting Satellite Mode
300 UNDERSTANDING YOUR INSTRUMENT PANEL Next, turn the knob surrounding the joystick in the center Reception Quality of the radio to scroll to Subscription, and then press and Satellite reception may be interrupted due to one of the release the joystick. All of the ESNs that apply to your following reasons: vehicle will display.
Page 303 UNDERSTANDING YOUR INSTRUMENT PANEL 301 SEEK Buttons additional three seconds will make the radio display the Press and release the SEEK buttons to search for the next Song Title all of the time (press and hold again to return channel in Satellite mode. Press the right switch to seek to normal display).
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button — Except REU Radio made, you can seek up, or down, or scan the channels Pressing this button once will turn on the Music Type and the radio will tune to the next station matching the mode for five seconds.
Page 305: Operating Instructions - Hands-Free Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 303 and press and release that button. If a button is not Operating Instructions — Hands-Free Phone (If selected within five seconds after pressing the SET but- Equipped) ton, the channel will continue to play but will not be Refer to “Hands-Free Communication (UConnect )”...
Page 306: Video Entertainment System (Ves)™ - If Equipped
304 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: SIRIUS service is not available in Hawaii and Two remote headphones has limited coverage in Alaska. Integrated remote storage in either screen location Refer to your Video Entertainment System (VES)™, RER Three different medias can be played simultaneously Navigation or REN Multimedia User Manuals for de- (Cabin speakers and Headphone Channels 1 and 2) tailed operating instructions.
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 The LCD screen(s) are located in the overhead compart- ment console. VES™ Remote Control Location NOTE: Refer to your VES™ User’s Manual for detailed operating instructions. Overhead Video Screens...
Page 308: Remote Sound System Controls - If Equipped
306 UNDERSTANDING YOUR INSTRUMENT PANEL system. Pressing the top of the rocker switch will increase REMOTE SOUND SYSTEM CONTROLS — IF the volume. Pressing the bottom of the rocker switch will EQUIPPED decrease the volume. Pressing the center button changes the operation of the radio from AM to FM, or Tape to CD mode, depending on which radio is in the vehicle.
Page 309: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 307 CD Player 2. If the disc is stained, clean the surface with a soft cloth, Pressing the top of the switch once will go to the next wiping from center to edge. track on the CD. Pressing the bottom of the switch once 3.
Page 310: Radio Operation And Cellular Phones
308 UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Manual Heating, Ventilation And Air Conditioning Under certain conditions, the cellular phone being ON in (HVAC) System your vehicle can cause erratic or noisy performance from The controls for the manual HVAC system in this vehicle your radio.
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Use this control to regulate the tem- Mode control allows you to choose perature of the air inside the passenger from several patterns of air distribu- compartment. Rotating the knob coun- tion.
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 air goes to the floor outlets. This feature gives improved NOTE: The air conditioning compressor operates in comfort during sunny but cool conditions. MIX and DEFROST, or a blend of these modes even if the A/C SNOWFLAKE button is not pressed.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The A/C can be deselected manually without disturb- If the RECIRCULATION button is pressed when the ing the mode control selection. system is in MIX, DEFROST, or FLOOR mode the Air Outlets RECIRCULATION LED indicator will flash 3 times The airflow from each of the instrument panel outlets can and then turn off to indicate RECIRCULATION mode be adjusted for direction, and turned on or off to control...
Page 315 UNDERSTANDING YOUR INSTRUMENT PANEL 313 Air Conditioning Operation Push on this button to engage the Air Conditioning (A/C). A light will illu- minate when the A/C System is en- gaged NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. Max A/C For maximum cooling use the A/C and RECIRCULA- Front Upper Three Zone Temperature Control...
Page 316: Rear Manual Climate Control Zone - If Equipped
314 UNDERSTANDING YOUR INSTRUMENT PANEL The Three-Zone Basic Temperature Control bottom panel The primary control for the rear blower is on the front controls rear Heating, Ventilation, and Air Conditioning climate control unit located on the instrument panel. (HVAC) operations. The Three-Zone Basic Temperature Control bottom panel has five positions;...
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 Only when the front control for the rear blower is in the RR position do the second row seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console, has an off position and a range of blower speeds.
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Temperature Control control is in FLOOR, DEFROST, or MIX modes, airflow When the blower knob on the front climate control unit is will be directed out of the rear floor outlets. set to any position other than RR , the rear temperature Rear Mode Control settings will be controlled by the rear temperature control knob on the front climate control unit.
Page 319: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Automatic Temperature Control (ATC) — If SYNC feature links the controls for all three zones, Equipped allowing one comfort setting for the cabin, if desired. Front Three-Zone ATC allows both driver and front The Infrared Three-Zone ATC System automatically passenger seat occupant, and rear seat occupants to maintains the interior comfort level desired by the driver select individual comfort settings.
Page 320 318 UNDERSTANDING YOUR INSTRUMENT PANEL Front Upper ATC Panel Front Lower ATC Panel 1 - System On/Off 9 - Air Conditioning (A/C) On/Off 1 - Blower Speed 4 - Rear HVAC Lock 2 - Blower Indicator 10 - AUTO Mode / Blower 2 - Rear Temperature / Rear 5 - Rear DEFROST 3 - Left Front Temperature...
Page 321 UNDERSTANDING YOUR INSTRUMENT PANEL 319 Automatic Operation NOTE: It is not necessary to move the temperature settings for 1. Press the AUTO button on the Front Upper ATC Panel cold or hot vehicles. The system automatically adjusts and the word AUTO will illuminate in the front ATC the temperature, mode and fan speed to provide display, along with three temperatures for driver, front comfort as quickly as possible.
Page 322 320 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation Panel Mode This system offers a full complement of manual override Air comes from the outlets in the instrument panel. features. The AUTO symbol in the front ATC display will Each of these outlets can be individually adjusted to be turned off when the system is being used in the direct the flow of air.
Page 323 UNDERSTANDING YOUR INSTRUMENT PANEL 321 Mix Mode flows through the air outlets. If ECONOMY mode is Air comes from the floor, defrost and side window desired, press the SNOWFLAKE button to turn off the demist outlets. This mode works best in cold or SNOWFLAKE mode in the ATC display, and deactivate snowy conditions.
Page 324 322 UNDERSTANDING YOUR INSTRUMENT PANEL button is selected. Push the button a second time to turn The REAR SYSTEM control for the Rear ATC System is off the RECIRCULATION mode LED and allow outside on the front lower ATC panel located on the instrument air into the vehicle.
Page 325 UNDERSTANDING YOUR INSTRUMENT PANEL 323 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs. 3. ATC is selected by adjusting the rear blower knob counterclockwise to AUTO. Once the desired temperature is displayed, the ATC System will automatically achieve and maintain that comfort level.
Page 326 324 UNDERSTANDING YOUR INSTRUMENT PANEL feature. Refer to the “Electronic Vehicle Information Rear Temperature Control Center (EVIC) — Customer-Programmable Features” To change the temperature in the rear of the vehicle, in this Section of the manual. rotate the temperature knob counterclockwise to lower the temperature, and clockwise to increase the tempera- Rear Blower Control ture.
Page 327: Summer Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Headliner Mode to provide proper corrosion protection and to protect Air comes from the outlets in the headliner. Each of against engine overheating. A 50% solution of ethylene these outlets can be individually adjusted to direct glycol antifreeze coolant in water is recommended.
Page 328: Window Fogging
326 UNDERSTANDING YOUR INSTRUMENT PANEL fresh air with the blower setting in high. This will ensure Operating Tips adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Vehicle windows tend to fog on the inside in mild, rainy and/or humid weather.
Page 329: A/C Air Filter- If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 327 A/C Air Filter— If Equipped On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to “Air Conditioning” in Section 7 of this manual for filter replacement instructions.
Page 331 STARTING AND OPERATING CONTENTS Starting Procedures ....332 Acceleration ......342 Automatic Transaxle .
Page 332 330 STARTING AND OPERATING Anti-Lock Brake System (ABS) ... . 349 Tire Pressure ......366 Anti-Lock Brake Light .
Page 333 STARTING AND OPERATING 331 MMT In Gasoline ....389 Replacement Parts ....394 Materials Added To Fuel .
Page 334: Starting Procedures
332 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the Be sure to turn off the engine and remove the key inside and outside mirrors, fasten your seat belt, and if from the ignition switch if you want to rest or present, instruct all other occupants to buckle their seat sleep in your car.
Page 335 STARTING AND OPERATING 333 Normal Starting (Above 32°F/0°C) Extremely Cold Weather Starting — Below 20°F (–29°C) 1. Do not depress the accelerator. Follow the same instructions in the “Normal Starting” 2. Use the Fob with Integrated Key to briefly turn the procedure.
Page 336 334 STARTING AND OPERATING If The Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push WARNING! the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 337: Engine Block Heater - If Equipped
STARTING AND OPERATING 335 If the engine shows no sign of starting after two 15– WARNING! second intervals of cranking with the accelerator pedal held to the floor, the “Normal Starting” procedure should Remember to disconnect the electrical cord before be repeated.
Page 338: Brake/Transaxle Interlock System
336 STARTING AND OPERATING NOTE: You must press and hold the brake pedal down the ignition switch is in the ON position. Always press while shifting out of PARK. the brake pedal first before moving the shift lever out of PARK.
Page 339: Four-Speed Or Six-Speed Automatic Transaxle
STARTING AND OPERATING 337 NOTE: If a malfunction occurs, the system will trap the The transaxle has only PRND shift positions. Downshifts key in the ignition cylinder to warn you that this safety are carried out by an Electronic Range Select (ERS) by feature is inoperable.
Page 340 338 STARTING AND OPERATING When parking on a hill, it is important to set the parking WARNING! (Continued) brake before placing the shift lever in PARK, otherwise Unintended movement of a vehicle could injure the load on the transaxle locking mechanism may make it those in and near the vehicle.
Page 341 STARTING AND OPERATING 339 Look at the shift indicator window on the console to NEUTRAL ensure the shift lever is in the PARK position. Place the shift lever into this gear only after the vehicle has come to a complete stop. The engine may be started When engaged in PARK, you will not be able to move in this range.
Page 342 340 STARTING AND OPERATING operating the vehicle under heavy loading conditions, CAUTION! (i.e., in hilly terrain, traveling into strong head winds or while towing heavy trailers). Under these conditions, If the transaxle operating temperature exceeds ac- using the “5” range will improve performance and ceptable limits, the vehicle computer will override extend transaxle life by reducing excessive shifting and DRIVE and select “5”...
Page 343 STARTING AND OPERATING 341 Switching from ERS to DRIVE can be done at any vehicle Odometer speed. To shift from DRIVE mode to ERS mode, move the Screen Dis- shift lever to the left (-) once. The current gear will be play maintained as the top gear.
Page 344: Reset Mode - Electronic Transaxle
342 STARTING AND OPERATING Reset Mode - Electronic Transaxle 5. Shift into the desired gear range and resume driving. The transaxle is monitored electronically for abnormal NOTE: Even if the transaxle can be reset, it is recom- conditions. If a condition is detected that could cause mended that you visit an authorized dealer at your damage, the transaxle automatically shifts into 2nd gear earliest possible convenience.
Page 345: Traction
STARTING AND OPERATING 343 2. Slow down if the road has standing water or puddles. WARNING! 3. Replace the tires when tread wear indicators first Rapid acceleration on slippery surfaces is dangerous. become visible. Unequal traction can cause sudden pulling of the 4.
Page 346: Flowing/Rising Water
344 STARTING AND OPERATING Flowing/Rising Water CAUTION! WARNING! Always check the depth of the standing water before driving through it. Never drive through Do not drive on, or cross, a road or a path where standing water that is deeper than the bottom of water is flowing and/or rising (as in storm run-off).
Page 347 STARTING AND OPERATING 345 CAUTION! (Continued) WARNING! Driving through standing water may cause dam- Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 348: Power Steering
346 STARTING AND OPERATING POWER STEERING WARNING! The standard power steering system will give you good vehicle response and increased ease of maneuverability Continued operation with reduced power steering in tight spaces. The system will provide mechanical assist could pose a safety risk to yourself and others. steering capability if power assist is lost.
Page 349: Parking Brake
STARTING AND OPERATING 347 apparent, and/or the system is not functioning as antici- PARKING BRAKE pated. Coordinate inspection efforts through an autho- When the parking brake is applied with the ignition rized dealer. switch ON, the brake light in the instrument cluster will turn on.
Page 350 348 STARTING AND OPERATING WARNING! Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transaxle in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury.
Page 351: Starting And Operating 349
STARTING AND OPERATING 349 ANTI-LOCK BRAKE SYSTEM (ABS) WARNING! ABS provides increased vehicle stability and brake per- formance under most braking conditions. The system NEVER leave children alone in a vehicle. Leaving automatically “pumps” the brakes during severe braking unattended children in a vehicle is dangerous for a conditions to prevent wheel lock-up.
Page 352 350 STARTING AND OPERATING A slight drop or fall away of the brake pedal at the end WARNING! (Continued) of the stop The Anti-Lock Brake System cannot prevent acci- dents, including those resulting from excessive WARNING! speed in turns, following another vehicle too The Anti-Lock Brake System contains sophisti- closely, or hydroplaning.
Page 353: Anti-Lock Brake Light
STARTING AND OPERATING 351 Anti-Lock Brake Light If both the Brake Warning Light and the ABS Light The ABS light monitors the Anti-Lock Brake remain on, the ABS and Electronic Brake Force Distribu- System. The light will come on when the tion (EBD) systems are not functioning.
Page 354: Electronic Brake Control System
352 STARTING AND OPERATING In the event power assist is lost for any reason (for WARNING! (Continued) example, repeated brake applications with the engine Driving a vehicle with the brake light on is dan- off), the brakes will still function. The effort required to gerous.
Page 355: Traction Control System (Tcs)
STARTING AND OPERATING 353 Traction Control System (TCS) light flashes during acceleration, ease up on the accelera- This system monitors the amount of wheel spin of each of tor and apply as little throttle as possible. Be sure to adapt the driven wheels.
Page 356: Brake Assist System (Bas)
354 STARTING AND OPERATING Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The The BAS cannot prevent the natural laws of phys- system detects an emergency braking situation by sens- ics from acting on the vehicle, nor can it increase ing the rate and amount of brake application, and then the traction afforded by prevailing road condi-...
Page 357: Electronic Stability Program (Esp)
STARTING AND OPERATING 355 Electronic Stability Program (ESP) ESP ON This system enhances directional control and stability of This is the normal operating mode for ESP on 2WD the vehicle under various driving conditions. ESP cor- vehicles. Whenever the vehicle is started, the ESP system rects for over/under steering of the vehicle by applying will be in this mode.
Page 358: Esp/Bas Warning Light
356 STARTING AND OPERATING gain traction. To turn ESP on again, momentarily depress Light comes on continuously with the engine running, a the ESP OFF switch. This will restore the normal ESP ON malfunction has been detected in either the ESP or the mode of operation.
Page 359: Tire Safety Information
STARTING AND OPERATING 357 TIRE SAFETY INFORMATION NOTE: P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. European-Metric tire sizing is based on European design standards.
Page 360 358 STARTING AND OPERATING Tires designed to this standard have the letter “T” High flotation tire sizing is based on U.S. design molded into the sidewall preceding the size designa- standards, and it begins with the tire diameter molded tion. Example: T145/80D18 103M. into the sidewall.
Page 361 STARTING AND OPERATING 359 EXAMPLE: R = Construction code — R means radial construction — D means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol —...
Page 362: Tire Identification Number (Tin)
360 STARTING AND OPERATING EXAMPLE: Load Identification: ..blank..= Absence of any text on the sidewall of the tire indicates a Standard Load (SL) Tire Extra Load (XL) = Extra load (or reinforced) tire Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load —...
Page 363 STARTING AND OPERATING 361 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards, and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 364: Tire Loading And Tire Pressure
362 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry...
Page 365 STARTING AND OPERATING 363 To determine the maximum loading conditions of your 3) tire size designed for your vehicle vehicle, locate the statement “The combined weight of 4) cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX kg or XXX spare tires.
Page 366 364 STARTING AND OPERATING 4. The resulting figure equals the available amount of manual to determine how this reduces the available cargo and luggage load capacity. For example, if “XXX” cargo and luggage load capacity of your vehicle. amount equals 1,400 lbs (635 kg) and there will be five NOTE: 150 lb (68 kg) passengers in your vehicle, the amount of The following table shows examples on how to calcu-...
Page 367 STARTING AND OPERATING 365...
Page 368: Tires - General Information
366 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle. Never Under-inflation increases tire flexing and can re- overload them.
Page 369 STARTING AND OPERATING 367 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to The tire pressure should be checked and adjusted, and the right or left.
Page 370 368 STARTING AND OPERATING is defined as the tire pressure after the vehicle has not Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) been driven for at least three hours, or driven less than during operation. Do not reduce this normal pressure 1 mile (1.6 km) after a three-hour period.
Page 371 STARTING AND OPERATING 369 Cuts and punctures in radial tires are repairable only in WARNING! the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs. High-speed driving, with your vehicle at or above maximum load, is dangerous. The added strain on Compact Spare Tire —...
Page 372 370 STARTING AND OPERATING WARNING! (Continued) CAUTION! Temporary-use spare tires have limited tread life. Because of the reduced ground clearance, do not take When the tread is worn to the tread wear indica- your vehicle through an automatic car wash with the tors, the temporary use spare tire needs to be compact spare installed.
Page 373 STARTING AND OPERATING 371 Tire Spinning WARNING! When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h), The limited-use spare tire is for emergency use or continuously for longer than 30 seconds, without only.
Page 374 372 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original-equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
Page 375 STARTING AND OPERATING 373 wear and correct cold tire inflation pressure. The manu- WARNING! facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance The tires and the spare tire should be replaced after when replacement is needed.
Page 376 374 STARTING AND OPERATING WARNING! WARNING! (Continued) Failure to equip your vehicle with tires having Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 377: Tire Chains
STARTING AND OPERATING 375 Tires may also cause the vehicle to pull to the left or right. CAUTION! Alignment will not correct this condition. See your authorized dealer for proper diagnosis. To avoid damage to your vehicle or tires, observe the following precautions: Improper alignment will not cause vehicle vibration.
Page 378: Snow Tires
376 STARTING AND OPERATING SNOW TIRES CAUTION! (Continued) Some areas of the country require the use of snow tires Do not drive for prolonged periods of time on dry during Winter. Standard tires are of the all-season type pavement. and satisfy this requirement as indicated by the M+S Observe the tire chain manufacturer’s instructions designation on the tire sidewall.
Page 379: Tire Rotation
STARTING AND OPERATING 377 TIRE ROTATION The suggested rotation method is the “forward-cross” Tires on the front and rear axles of vehicles operate at shown in the following diagram. different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
Page 380: Tire Pressure Monitor System (Tpms)
378 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure if The TPMS will warn the driver of a low tire pressure the tire pressure falls below the low pressure warning based on the cold inflation tire pressure requirements threshold for any reason, including low temperature found on the tire placard located on the driver’s-side...
Page 381 STARTING AND OPERATING 379 For example, your vehicle may have a recommended CAUTION! cold (parked for more than three hours) tire pressure of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) The TPMS has been optimized for the original and the measured tire pressure is 30 psi (207 kPa), a equipment tires and wheels.
Page 382: Basic Tpms Without Evic - If Equipped
380 STARTING AND OPERATING NOTE: NOTE: Seasonal temperature changes will affect tire The TPMS is not intended to replace normal tire care pressure, and the TPMS will monitor the actual tire and maintenance, or to provide warning of a tire pressure in the tire.
Page 383 STARTING AND OPERATING 381 The TPMS Telltale Warning Light will illumi- ignition key is cycled, this sequence will repeat, provid- nate in the instrument cluster, and an audible ing the system fault still exists. The TPMS Warning Lamp chime will be activated when one or more of will turn off when the fault condition no longer exists.
Page 384: Premium Tpms With Evic - If Equipped
382 STARTING AND OPERATING NOTE: Telltale Warning Light will turn off as long as no tire 1. The compact spare tire (if equipped) does not have a pressure is below the low-pressure warning limit in any TPMS sensor. Therefore the TPMS will not monitor the of the four active road tires.
Page 385 STARTING AND OPERATING 383 Three Trigger Modules (mounted in three of the four wheel wells) Various TPMS messages, which display in the Elec- tronic Vehicle Information Center (EVIC), and graph- ics displaying tire pressures Yellow TPMS Telltale Warning Light TPMS Low Pressure Warnings The TPMS Telltale Warning Light will illuminate in the instrument cluster, and an audible chime will be acti- vated when one or more of the four active road tire...
Page 386 384 STARTING AND OPERATING the TPMS Telltale Warning Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. Check TPMS Message The TPMS Telltale Warning Light will flash on and off for 75 seconds, and remain on solid when a system fault is...
Page 387 STARTING AND OPERATING 385 will not be present, and a pressure value will be dis- 2. If you install the compact spare tire in place of a road played instead of dashes. A system fault can occur by any tire that has a pressure below the low-pressure warning of the following scenarios: limit, upon the next ignition key cycle, the TPMS Telltale Warning Light will remain on, a chime will sound, and...
Page 388: Fuel Requirements
386 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and This device must accept any interference received, reinstall it on the vehicle in place of the compact spare, including interference that may cause undesired the TPMS will update automatically. In addition, the operation.
Page 389: 4.0L Gasoline Engine
STARTING AND OPERATING 387 regular gasolines, and in some circumstances may result Poor quality gasoline can cause problems such as hard in poorer performance. starting, stalling and hesitations. If you experience these symptoms, try another brand of “regular” gasoline be- 4.0L Gasoline Engine fore considering service for the vehicle.
Page 390: Gasoline/Oxygenate Blends
388 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- Problems that result from using methanol/gasoline or lines. Properly blended reformulated gasolines will pro- E85 Ethanol blends are not the responsibility of the vide excellent performance and durability of engine and manufacturer.
Page 391: Mmt In Gasoline
STARTING AND OPERATING 389 To fix a Non-FFV vehicle inadvertently fueled once with of gasoline may not be indicated on the gasoline pump, E-85 perform the following: therefore, you should ask your gasoline retailer whether the gasoline contains MMT. drain the fuel tank (see your authorized dealer) It is even more important to look for gasolines without change the engine oil and oil filter MMT in Canada, because MMT can be used at levels...
Page 392: Fuel System Cautions
390 STARTING AND OPERATING Fuel System Cautions Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not CAUTION! the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control Follow these guidelines to maintain your vehicle’s systems can result in civil penalties being assessed performance: against you.
Page 393: Flexible Fuel - 3.3L Engines Only
STARTING AND OPERATING 391 FLEXIBLE FUEL — 3.3L ENGINES ONLY WARNING! (Continued) E-85 General Information NEVER run the engine in a closed area, such as a The information in this section is for Flexible Fuel Ve- garage, and NEVER sit in a parked vehicle with hicles (FFV) only.
Page 394: Ethanol Fuel (E-85)
392 STARTING AND OPERATING E-85 Fuel Cap E-85 Badge ETHANOL FUEL (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 Decal and/or fuel filler door label can operate on E-85.
Page 395: Fuel Requirements
STARTING AND OPERATING 393 you drive the vehicle immediately after refueling for at WARNING! least 5 miles (8 km) Ethanol vapors are extremely flammable and could Observing these precautions will avoid possible hard cause serious personal injury. Never have any smok- starting and/or significant deterioration in drivability ing materials lit in or near the vehicle when remov- during warm up.
Page 396: Selection Of Engine Oil For Flexible Fuel Vehicles (Ffv) E-85 And Gasoline Vehicles
Material Standard MS-6395. MS-6395 Replacing fuel system components with non-ethanol contains additional requirements, developed during ex- compatible components can damage your vehicle. tensive fleet testing, to provide additional protection to Chrysler LLC engines. Use MOPAR or an equivalent oil meeting the specification MS-6395.
Page 397: Maintenance
STARTING AND OPERATING 395 Maintenance NOTE: The driver’s side sliding door cannot be opened If you operate the vehicle using E-85 fuel, follow the while the fuel door is open. This feature operates only maintenance schedule section of this manual. when the sliding door is fully closed prior to opening the fuel door.
Page 398: Loose Fuel Filler Cap Message
396 STARTING AND OPERATING WARNING! WARNING! Never have any smoking materials lit in or near A fire may result if gasoline is pumped into a the vehicle when the gas cap is removed or the portable container that is inside of a vehicle. You tank filled.
Page 399: Vehicle Loading
STARTING AND OPERATING 397 If the problem continues, the message will appear the Gross Vehicle Weight Rating (GVWR) next time the vehicle is started. See your authorized Gross Axle Weight Rating (GAWR) — Front dealer as soon as possible. See Section 7 of this manual for more information.
Page 400 398 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Rim Size The GAWR is the maximum capacity of the front and rear This is the rim size that is appropriate for the tire size axles. Distribute the load over the front and rear axles listed.
Page 401 STARTING AND OPERATING 399 Overloading Loading The load carrying components (axle, springs, tires, To load your vehicle properly, first figure out its empty wheels, etc.) of your vehicle will provide satisfactory weight, axle-by-axle and side-by-side. Store heavier items service as long as you do not exceed the GVWR and front down low and be sure you distribute their weight as evenly and rear GAWR.
Page 402 400 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that LOADING TABLE — EXAMPLE ONLY neither the GVWR or the GAWR capacities have been Front Axle Rear Axle exceeded. Empty Weight 2,140 lbs 1,470 lbs (971 kg) (667 kg) Load (Driver, 360 lbs (163 kg)
Page 403: Trailer Towing
STARTING AND OPERATING 401 TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information The GTW is the weight of the trailer plus the weight of all on limits to the type of towing you can reasonably do cargo, consumables and equipment (permanent or tem- with your vehicle.
Page 404 402 STARTING AND OPERATING that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 405 STARTING AND OPERATING 403 also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier tongue weights (TW), and may be required depending on vehicle and trailer configuration/loading to comply with gross axle weight rating (GAWR) requirements.
Page 406 404 STARTING AND OPERATING With Weight-Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (In- correct) Trailer Hitch Classification Your vehicle may be factory-equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See an authorized dealer for package content.
Page 407 STARTING AND OPERATING 405 The following chart provides the industry standard for TRAILER HITCH CLASSIFICATIONS the maximum trailer weight a given trailer hitch class can Max. GTW (Gross Trailer Class tow, and should be used to assist you in selecting the Wt.) correct trailer hitch for your intended towing condition.
Page 408 406 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Com- Engine/Transaxle Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. bined Wt. Rating) Up to 2 persons &...
Page 409 STARTING AND OPERATING 407 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 410 408 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional During the first 500 miles (805 km) of trailer factory-installed options, or authorized dealer-installed towing, limit your speed to 50 mph (80 km/h). options, must be considered as part of the total load on your vehicle.
Page 411 STARTING AND OPERATING 409 Vehicles with trailers should not be parked on a grade. WARNING! (Continued) When parking, apply the parking brake on the tow Make certain that the load is secured in the trailer vehicle. Put the tow vehicle automatic transmission in and will not shift during travel.
Page 412 410 STARTING AND OPERATING Towing Requirements — Tires When replacing tires, refer to the “Tires–General Infor- mation” section of this manual for proper tire replace- Do not attempt to tow a trailer while using a compact ment procedures. Replacing tires with a higher load spare tire.
Page 413 STARTING AND OPERATING 411 Trailer brakes are recommended for trailers over WARNING! (Continued) 1,000 lbs (454 kg) and required for trailers in excess of Towing any trailer will increase your stopping 2,000 lbs (907 kg). distance. When towing you should allow for addi- tional space between your vehicle and the vehicle CAUTION! in front of you.
Page 414 412 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations. Four-Pin Connector 1 — Female Pins 4 — Park 2 —...
Page 415: Towing Tips
STARTING AND OPERATING 413 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Towing Tips — Automatic Transaxle The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, move the gear selector lever into third gear (with four-speed transaxle) or fifth gear (with six-speed transaxle).
Page 416 414 STARTING AND OPERATING The automatic transaxle fluid and filter should be Use speed control in flat terrain and with light loads to changed if you REGULARLY tow a trailer for more than maximize fuel efficiency. 45 minutes of continuous operation. Refer to the “Main- Towing Tips —...
Page 417: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 415 RECREATIONAL TOWING (BEHIND NOTE: If the vehicle requires towing, make sure all four MOTORHOME, ETC.) wheels are off the ground. CAUTION! Towing this vehicle behind another vehicle (flat- towing with all four wheels on the ground) is not recommended.
Page 419: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....418 Jump-Starting Procedure ....432 If Your Engine Overheats .
Page 420: Hazard Warning Flasher
418 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning Flash- The Hazard Warning Flasher switch is located in the ers may wear down your battery. center of the instrument panel above the radio. IF YOUR ENGINE OVERHEATS Press the switch to turn on the Hazard In any of the following situations, you can reduce the...
Page 421 WHAT TO DO IN EMERGENCIES 419 the fan control to high. This allows the heater core to act WARNING! as a supplement to the radiator and aids in removing heat from the engine cooling system. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling CAUTION! coolant.
Page 422: Jacking And Tire Changing
420 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) For vehicles equipped with Stow ’n Go seating, if WARNING! it is necessary to retrieve the spare tire from under Getting under a jacked-up vehicle is dangerous. the vehicle on the side of the vehicle close to The vehicle could slip off the jack and fall on you.
Page 423 WHAT TO DO IN EMERGENCIES 421 Spare Tire Removal For vehicles equipped with Stow ’n Go seating, the spare tire is stowed inside a protective cover located under the center of the vehicle by means of a cable winch mecha- nism.
Page 424 422 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
Page 425 WHAT TO DO IN EMERGENCIES 423 6. Block both the front and rear of the WARNING! (Continued) wheel diagonally opposite the jacking Always park on a firm, level surface as far from position. For example, if changing the the edge of the roadway as possible before raising right front tire, block the left rear the vehicle.
Page 426 424 WHAT TO DO IN EMERGENCIES 2. To remove the compact spare tire/cover assembly, WARNING! (Continued) assemble the winch handle extensions to form a “T’ and If working on or near a roadway, be extremely fit the winch “T” handle over the drive nut. Rotate the careful of motor traffic.
Page 427 WHAT TO DO IN EMERGENCIES 425 WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift.
Page 428 426 WHAT TO DO IN EMERGENCIES 4. When the compact spare tire/cover assembly is clear 5. There are two jack engagement locations on each side of the vehicle, stand the tire/cover assembly upright and of the vehicle body. These locations are on the sill flange remove the wheel spacer by squeezing the two retainer of the vehicle body.
Page 429 WHAT TO DO IN EMERGENCIES 427 Jack Location...
Page 430 428 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on Raising the vehicle higher than necessary can make locations other than those indicated in Step 5. the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 431 WHAT TO DO IN EMERGENCIES 429 10. Lower the vehicle by turning the jack screw to the 13. Place the deflated (flat) tire and compact spare tire left. cover assembly. in the rear cargo area. Do not stow the deflated tire in the spare tire location. Have the full- 11.
Page 432 430 WHAT TO DO IN EMERGENCIES of operation, and after each time a tire is changed, to WARNING! allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts A loose compact spare tire/cover assembly, thrown should then be tightened to recommended torque.
Page 433 WHAT TO DO IN EMERGENCIES 431 3. Turn the compact spare tire so that the valve stem is WARNING! down, and place the tire into the spare tire/cover assem- bly. Slide the wheel spacer through the center of the Verify that both retainer tabs of the wheel spacer wheel and spare tire/cover assembly, so that the two have been properly extended through the center of retainer tabs snap out and engage the spare tire cover on...
Page 434: Jump-Starting Procedure
432 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) If the vehicle has a discharged battery, booster For vehicles equipped with Stow ’n Go seating, the cables may be used to obtain a start from another winch mechanism is designed specifically to stow a vehicle.
Page 435 WHAT TO DO IN EMERGENCIES 433 2. When a boost is provided by a battery in another WARNING! (Continued) vehicle, park that vehicle within booster cable reach and Take special care to avoid the radiator cooling fan do not let the vehicles touch. Set the parking brake, place whenever the hood is raised.
Page 436 434 WHAT TO DO IN EMERGENCIES 6. Start the engine in the vehicle that has the booster WARNING! battery. Let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. Do not permit vehicles to touch each other, as this could establish a ground connection and personal 7.
Page 437: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 435 FREEING A STUCK VEHICLE CAUTION! If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your Racing the engine or spinning the wheels too fast steering wheel right and left to clear the area around the may lead to transmission overheating and failure.
Page 438 436 WHAT TO DO IN EMERGENCIES If the transmission is not operative, or if the vehicle is CAUTION! (Continued) to be towed more than 100 miles (160 km), the vehicle If the vehicle being towed requires steering, the must be towed with the front wheels off the ground. ignition switch must be in the OFF position, not in the LOCK or ACC positions.
Page 439 WHAT TO DO IN EMERGENCIES 437 Towing This Vehicle Behind Another Vehicle (Flat Towing This Vehicle Behind Another Vehicle With Towing With All Four Wheels On The Ground) A Tow Dolly Flat towing of vehicles equipped with an automatic The manufacturer does not recommend that you tow a transmission, is only permitted within the limitations front wheel drive vehicle on a tow dolly.
Page 441 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 3.3/3.8L ..441 Engine Oil ......446 Engine Compartment —...
Page 442 440 MAINTAINING YOUR VEHICLE Windshield Wiper Blades ....457 Quad Headlights ..... 484 Cooling System .
Page 443: Engine Compartment - 3.3/3.8L
MAINTAINING YOUR VEHICLE 441 ENGINE COMPARTMENT — 3.3/3.8L 1 — Air Cleaner Filter 7 — Engine Oil Fill 2 — Automatic Transmission Dipstick (3.3L Only) 8 — Engine Oil Dipstick 3 — Brake Fluid Reservoir 9 — Coolant Pressure Cap 4 —...
Page 444: Engine Compartment - 4.0L
442 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 4.0L 1 — Power Steering Fluid Reservoir 7 — Engine Oil Dipstick 2 — Air Cleaner Filter 8 — Engine Oil Fill 3 — Brake Fluid Reservoir 9 — Coolant Pressure Cap 4 — Battery 10 —...
Page 445: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 443 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 446: Emissions Inspection And Maintenance Programs
444 MAINTAINING YOUR VEHICLE filler cap message will be displayed in the instrument Indicator Light (MIL) is functioning and is not on when cluster. Tighten the gas cap until a clicking sound is the engine is running, and that the OBD II system is heard.
Page 447: Replacement Parts
MAINTAINING YOUR VEHICLE 445 4. As soon as you turn your key to the ON position, you you may need to do nothing more than drive your will see the MIL symbol come on as part of a normal bulb vehicle as you normally would in order for your OBD II check.
Page 448: Dealer Service
446 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 449 API certified and meet Overfilling or underfilling will cause oil aeration, or the requirements of Chrysler Material Standard MS-6395. loss of oil pressure. This could damage your engine.
Page 450 448 MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil For information on engine oil filler cap location, refer to Identification Symbol “Engine Compartment” in this section. This symbol means that the oil has Lubricants that do not have both the engine oil certifica- been certified by the American tion mark and the correct SAE viscosity grade number, Petroleum Institute (API).
Page 451: Engine Oil Filter
MAINTAINING YOUR VEHICLE 449 Synthetic Engine Oils station, or governmental agency for advice on how and You may use synthetic engine oils provided the recom- where used oil and oil filters can be safely discarded in mended oil quality requirements are met, and the recom- your area.
Page 452: Exhaust System
450 MAINTAINING YOUR VEHICLE Exhaust System WARNING! The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust The air induction system (air cleaner, hoses, etc.) can system. provide a measure of protection in the case of engine backfire.
Page 453 MAINTAINING YOUR VEHICLE 451 WARNING! CAUTION! Exhaust gases can injure or kill. They contain carbon Damage to the catalytic converter can result if your monoxide (CO) which is colorless and odorless. vehicle is not kept in proper operating condition. In Breathing it can make you unconscious and can the event of engine malfunction, particularly involv- eventually poison you.
Page 454: Maintenance-Free Battery
452 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! Do not shut OFF the engine or interrupt the ignition A hot exhaust system can start a fire if you park over when the transaxle is in gear and the vehicle is in materials that can burn.
Page 455: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 453 WARNING! CAUTION! Battery fluid is a corrosive acid solution and can It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin or clothing.
Page 456 454 MAINTAINING YOUR VEHICLE include cleaning of the condenser fins and a system Refrigerant Recovery and Recycling performance check. Drive belt tension should also be R-134a air conditioning refrigerant is a hydrofluoro- checked at this time. carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
Page 457 MAINTAINING YOUR VEHICLE 455 WARNING! Do not remove the A/C air filter while the blower is operating or personal injury may result. The A/C air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1.
Page 458: Steering Shaft Seal
456 MAINTAINING YOUR VEHICLE damage when other maintenance is performed. If leakage CAUTION! or damage is evident, the universal joint boot and grease should be replaced immediately. The A/C air filter is labeled with an arrow to indicate airflow direction through the filter. Failure to prop- Continued operation could result in failure of the univer- erly install the filter will result in the need to replace sal joint due to water and dirt contamination of the...
Page 459: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 457 attention should also be given to hood latching compo- Avoid using the wiper blades to remove frost or ice from nents to insure proper function. When performing other the windshield. Keep the blade rubber out of contact with underhood services, the hood latch, release mechanism petroleum products such as engine oil, gasoline, etc.
Page 460: Cooling System
458 MAINTAINING YOUR VEHICLE Cooling System WARNING! WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care When working near the radiator cooling fan, dis- must be exercised when filling or working around connect the fan motor lead or turn the ignition the washer solution.
Page 461 MAINTAINING YOUR VEHICLE 459 rusty in appearance, the system should be drained, Cooling System — Drain, Flush and Refill flushed and refilled with fresh coolant. Check the front of If the engine coolant (antifreeze) is dirty or contains a the A/C condenser for any accumulation of bugs, leaves, considerable amount of sediment, clean and flush with a etc.
Page 462 460 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) This vehicle has not been designed for use with Mixing of engine coolant (antifreeze) other than Propylene Glycol based engine coolant (anti- specified Hybrid Organic Additive Technology freeze). Use of Propylene Glycol based engine (HOAT) engine coolant (antifreeze), may result in coolant (antifreeze) is not recommended.
Page 463 MAINTAINING YOUR VEHICLE 461 When adding engine coolant (antifreeze), a minimum NOTE: Mixing engine coolant (antifreeze) types will solution of 50% recommended MOPAR Antifreeze/ decrease the life of the engine coolant (antifreeze) and Coolant Five Year/100,000 Mile Formula HOAT (Hybrid will require more frequent coolant changes.
Page 464 462 MAINTAINING YOUR VEHICLE rules for your community. To prevent ingestion by ani- WARNING! mals or children do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it The warning words “DO NOT OPEN HOT” on to remain in puddles on the ground. If ingested by a the cooling system pressure cap are a safety pre- child, contact a physician immediately.
Page 465 MAINTAINING YOUR VEHICLE 463 of this. As long as the engine operating temperature is Do not overfill the coolant recovery bottle. satisfactory, the coolant bottle need only be checked once Check engine coolant (antifreeze) freeze point in the a month. radiator and in the coolant recovery bottle.
Page 466: Brakes
464 MAINTAINING YOUR VEHICLE Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, also keep the front of the condenser clean also. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting Do not change the thermostat for Summer or Winter or riding on the brake pedal can result in abnormally operation.
Page 467 MAINTAINING YOUR VEHICLE 465 Add enough fluid to bring the level up to the require- WARNING! (Continued) ments described on the brake fluid reservoir. With disc Use of a brake fluid that has a lower initial boiling brakes, fluid level can be expected to fall as the brake point than the recommended MOPAR DOT 3 pads wear.
Page 468: Automatic Transaxle
466 MAINTAINING YOUR VEHICLE Automatic Transaxle only the manufacturer’s recommended transmission The automatic transaxle and differential assembly are fluid. Refer to “Fluids, Lubricants and Genuine Parts” in contained within a single housing. this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed The fluid level in the automatic transaxle should be level using the recommended fluid.
Page 469 MAINTAINING YOUR VEHICLE 467 Fluid Level Check — 3.8L and 4.0L Engines with 1. The vehicle must be on level ground. Six-Speed Automatic Transaxle — If Equipped 2. The engine should be running at curb idle speed for a The six-speed automatic transaxle is a sealed unit and has minimum of 60 seconds.
Page 470: Appearance Care And Protection From Corrosion
468 MAINTAINING YOUR VEHICLE a. If the fluid is hot, the reading should be in the If the transaxle is disassembled for any reason, the fluid crosshatched area marked “HOT” (between the upper and filter should be changed. two holes in the dipstick). Special Additives b.
Page 471 MAINTAINING YOUR VEHICLE 469 road surfaces on which the vehicle is operated, extreme Atmospheric fallout/industrial pollutants hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- body protection. Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR Car Wash or a mild The following maintenance recommendations will enable car wash soap, and rinse the panels completely with...
Page 472 470 MAINTAINING YOUR VEHICLE coating, have your vehicle repaired as soon as pos- CAUTION! sible. The cost of such repairs is considered the respon- sibility of the owner. Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch If you carry special cargo such as chemicals, fertilizers, metal and painted surfaces.
Page 473 MAINTAINING YOUR VEHICLE 471 a nonabrasive, non-acidic cleaner. Do not use scouring MOPAR Spot & Stain Remover if absolutely necessary. pads, steel wool, a bristle brush, or metal polishes. Only Do not use harsh cleaners or Armorall. Use MOPAR MOPAR or equivalent is recommended. Do not use Total Clean to clean vinyl upholstery oven cleaner.
Page 474 472 MAINTAINING YOUR VEHICLE For grease stains, apply MOPAR Multi-Purpose WARNING! Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Do not use any solvents or protectants on Yes Essen- closed areas they may cause respiratory harm.
Page 475 MAINTAINING YOUR VEHICLE 473 applique. Rub the applique with firm pressure then buff Glass Surfaces lightly with a clean cotton cloth until a high gloss shine is All glass surfaces should be cleaned on a regular basis achieved. with MOPAR Glass Cleaner or any commercial household-type glass cleaner.
Page 476: Cleaning The Instrument Panel Cupholders
474 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be Cleaning the Instrument Panel Cupholders used, but do not use high alcohol content or abrasive Removal cleaners. If soap is used, wipe clean with a clean damp Pull the flexible liner from the cupholder drawer starting rag.
Page 477: Fuses
MAINTAINING YOUR VEHICLE 475 Installation CAUTION! Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the When installing the Totally Integrated Power corresponding openings in the drawer. Module cover, it is important to ensure the cover is properly positioned and fully latched.
Page 478 476 MAINTAINING YOUR VEHICLE The numbers inside the TIPM cover correspond to the FUSES/TIPM following table. Cartridge Cavity Mini-Fuse Description Fuse FUSES/TIPM 40 Amp — Power Memory Cartridge Cavity Mini-Fuse Description Green Seat (If Equipped) Fuse 40 Amp — PZEV Motor/Flex 40 Amp —...
Page 479 MAINTAINING YOUR VEHICLE 477 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse 20 Amp — Powertrain Control — 20 Amp — Yellow Module (PCM) Yellow Trans Range — 10 Amp Trailer Tow 60 Amp — Radiator Fan Yellow —...
Page 480 478 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 20 Amp Ignition Off Draw — 20 Amp Ignition Off Yellow — Vehicle Enter- Yellow Draw— Cabin tainment System Compartment (IOD-VES), Satellite Node (IOD-CCN), Digital Audio Re- Wireless Control ceiver (SDARS),...
Page 481 MAINTAINING YOUR VEHICLE 479 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 20 Amp COL MOD, IR SNS, — 10 Amp Occupant Restraint Yellow Heater Ventilation, Controller/ Air Conditioning/ Occupant Classifi- Automatic Tem- cation Module perature Control (ORC/OCM) (HVAC/ATC), Rear...
Page 482 480 MAINTAINING YOUR VEHICLE FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 15 Amp Cabin Compart- — 20 Amp Fuel Pump (FUEL Blue ment Node Interior Yellow PUMP), Diesel Lift Light (CCN INT Pump (DSL LIFT LIGHT), Switch PUMP) —...
Page 483 MAINTAINING YOUR VEHICLE 481 FUSES/TIPM FUSES/TIPM Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse — 10 Amp Occupant Classifi- — 10 Amp Park Assist (PRK cation Module ASST), Heater Ven- (OCM) tilation, Air Condi- tioning Module — 15 Amp Rear Wiper Module (HVAC MOD), Blue...
Page 484: Vehicle Storage
482 MAINTAINING YOUR VEHICLE VEHICLE STORAGE FUSES/TIPM If you are leaving your vehicle dormant for more than Cartridge Cavity Mini-Fuse Description 21 days, you may want to take steps to protect your Fuse battery. You may do the following: — 25 Amp Lock/Unlock Mo- Natural...
Page 485: Replacement Light Bulbs
MAINTAINING YOUR VEHICLE 483 REPLACEMENT LIGHT BULBS LIGHT BULBS — Exterior Bulb Number Backup, Tail, Stop Light ....3157 LIGHT BULBS — Interior Bulb Number Center High-Mounted Stop Light .
Page 486: Bulb Replacement
484 MAINTAINING YOUR VEHICLE BULB REPLACEMENT NOTE: On vehicles equipped with High Intensity Dis- charge Headlights (HID), when the headlights are turned High Intensity Discharge Headlights (HID) — If on, there is a blue hue to the lights. This diminishes and Equipped becomes more white after approximately 10 seconds, as The headlights are a type of high voltage discharge tube.
Page 487: Front Park/Turn Signal Lights
MAINTAINING YOUR VEHICLE 485 Front Side Marker Lights CAUTION! 1. Raise the hood to access the rear of the headlight Do not touch the new bulb with your fingers. Oil housing. contamination will severely shorten bulb life. If the NOTE: Access is somewhat limited. You may have to bulb comes in contact with an oily surface, clean the remove the inner fender well or remove the headlight bulb with rubbing alcohol.
Page 488: Rear Tail, Stop, Turn Signal, Side Marker And Backup Lights
486 MAINTAINING YOUR VEHICLE 1. From behind the bumper fascia, or the access panel on 2. Remove the tail light assembly by removing the two the air dam, twist the bulb counterclockwise, and remove screws from the inboard side. Use a fiber stick or similar bulb.
Page 489 MAINTAINING YOUR VEHICLE 487 NOTE: If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint. The PRY location is best closest to the studs while dislodging them separately. Bulb Location 1 —...
Page 490: Center High-Mounted Stop Light (Chmsl)
488 MAINTAINING YOUR VEHICLE 5. Replace the bulb, reinstall the socket, and reattach the 1. Using a small screwdriver, press inward the locking light assembly. tab on the outboard side of the light assembly and pull down on the light assembly for removal. Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable 2.
Page 491: Fluids, Lubricants And Genuine Parts
Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Engine Oil (3.3L and 3.8L Engines) Chrysler Material Standard MS-6395. Refer to your oil filler cap for cor- rect SAE grade Use API Certified SAE 10W-30 Engine Oil, meeting the requirements of Engine Oil (4.0L Engine)
Page 492: Chassis
490 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic MOPAR ATF+4 Automatic Transmission Fluid Transaxle Brake Master MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not Cylinder available, then DOT 4 is acceptable. Use only recommended brake fluids. Power Steering MOPAR Power Steering Fluid +4 or MOPAR ATF+4 Automatic Transmission Fluid Reservoir...
Page 493: Fluids And Capacities
MAINTAINING YOUR VEHICLE 491 FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 20 Gallons 76 Liters Engine Oil with Filter 3.3L and 3.8L Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters 4.0 Liter Engine (SAE 10W-30, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 3.3, 3.8, and 4.0 Liter Engine (MOPAR Engine Coolant/...
Page 495 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..494 Required Maintenance Intervals ..496 Maintenance Schedule ....494...
Page 496 494 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type, The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the Emissions Con- On Non-EVIC equipped vehicles, CHAngE OIL will trol System.
Page 497 MAINTENANCE SCHEDULES 495 NOTE: under “Odometer/Trip Odometer” in the “Instrument The oil change indicator message will not monitor the Cluster Descriptions section of this manual. time since the last oil change. Change your vehicle’s At Each Stop For Fuel oil if it has been six months since your last oil change, even if the oil change indicator message is NOT Check the engine oil level about five minutes after a illuminated.
Page 498 496 MAINTENANCE SCHEDULES Check the fluid levels of the coolant reservoir, the CAUTION! brake master cylinder, the power steering and the transaxle and add as needed. Failure to perform the required maintenance items may result in damage to the vehicle. Check all lights and other electrical items for correct operation.
Page 499 Inspect the exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 500 Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 501 Inspect the brake linings, replace if necessary. Odometer Reading Date Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 502: Service Schedule
Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 503 Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 504 Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 505 Replace the air conditioning filter. Inspect the brake linings, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 506 Inspect the front suspension, tie rod ends and boot seals, replace if necessary. and 4.0L engines). Replace the timing belt (4.0L engine). Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 507 Inspect the engine air cleaner filter, replace if necessary. Replace the air conditioning filter. Inspect the brake linings, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 508 Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Replace accessory drive belt(s). Change the automatic transaxle fluid & filter. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 509 Odometer Reading Date Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 510 508 MAINTENANCE SCHEDULES 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 511 MAINTENANCE SCHEDULES 509 † This maintenance is recommended by the manufac- turer, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 513: If You Need Consumer Assistance
Reporting Safety Defects ....516 Chrysler LLC Customer Center ... 514 In The 50 United States And Washington, D.C.
Page 514 512 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....517 Traction Grades ..... . 519 Department Of Transportation Uniform Tire Temperature Grades .
Page 515: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 513 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 516: Chrysler Llc Customer Center
Phone: (800) 992-1997 ship. They want to know if you need assistance. Chrysler Canada Inc. Customer Center If an authorized dealership is unable to resolve the P.O. Box 1621 concern, you may contact the manufacturer’s customer Windsor, Ontario N9A 4H6 center.
Page 517: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 515 Customer Assistance For The Hearing Or Speech have any questions about the service contract, call the Impaired (TDD/TTY) manufacturer’s Service Contract National Customer Hot- To assist customers who have hearing difficulties, the line at 1-800-521-9922. manufacturer has installed special TDD (Telecommuni- The manufacturer will not stand behind any service cation Devices for the Deaf) equipment at its customer...
Page 518: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) sincere efforts to resolve any warranty issues or related See the Warranty Information Booklet for the terms and concerns. provisions of Chrysler Motors LLC warranties applicable to this vehicle. WARNING! MOPAR PARTS Engine exhaust, some of its constituents, and certain...
Page 519: In Canada
If you believe that your vehicle has a safety defect, you need in diagnosing/troubleshooting, problem solving, should contact the Customer Service Department imme- maintaining, servicing, and repairing Chrysler LLC diately. Canadian customers who wish to report a safety vehicles. A complete working knowledge of the ve-...
Page 520: Department Of Transportation Uniform Tire
Chrysler LLC vehicles. your vehicle. Included are starting, operating, emergency and main-...
Page 521: Treadwear
IF YOU NEED CONSUMER ASSISTANCE 519 Treadwear Traction Grades The Treadwear grade is a comparative rating, based on The Traction grades, from highest to lowest, are AA, A, B, the wear rate of the tire when tested under controlled and C. These grades represent the tire’s ability to stop on conditions on a specified government test course.
Page 522 520 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under con- a tire that is properly inflated and not overloaded.
Page 523 INDEX...
Page 524 522 INDEX Adding Engine Coolant (Antifreeze) ..460 Airbag Maintenance ..... . . 75 Adding Fuel .
Page 525 INDEX 523 Automatic Headlights ....176 Jump Starting ......432 Automatic Temperature Control (ATC) .
Page 526 524 INDEX Calibration, Compass ....257,263 Check Engine Light Camera, Rear ......196 (Malfunction Indicator Light) .
Page 527 INDEX 525 Computer, Trip/Travel ....262 Radiator Cap ......461 Connector Selection of Coolant (Antifreeze) .
Page 528 526 INDEX Disposal Electronic Stability Program ....355 Antifreeze (Engine Coolant) ....462 Electronic Speed Control (Cruise Control) .
Page 529 INDEX 527 Exhaust Gas Caution ....53,390 Exterior Folding Mirrors ....104 Flooded, Starting .
Page 530 528 INDEX Replacement Parts ..... 394 Additives ......389 Starting .
Page 531 INDEX 529 Gasoline, Reformulated ....388 Headlights ......176 Gauges Cleaning .
Page 532 530 INDEX Ignition Key Removal ..... 14 Key, Programming ......17 Illuminated Entry .
Page 533 INDEX 531 Anti-Lock ......248 License ......488 Automatic Headlights .
Page 534 532 INDEX Voltage ......242 Manual, Service ......517 Warning (Instrument Cluster Description) .
Page 535 INDEX 533 Navigation System ..... . . 196 Viscosity ......448,491 New Vehicle Break-In Period .
Page 536 534 INDEX Placard, Tire and Loading Information ..362 Radial Ply Tires ......369 Power Radiator Cap (Coolant Pressure Cap) .
Page 537 INDEX 535 Removable Floor Console ....227 Satellite Radio ..... . . 298,303 Replacement Keys .
Page 538 536 INDEX Heated ......148 Shoulder Belts ......57 Lumbar Support .
Page 539 INDEX 537 Steering Temperature Control, Automatic (ATC) ..317 Power ......346 Temperature Gauge, Engine Coolant .
Page 540 538 INDEX Inflation Pressures ..... 367 Disabled Vehicle ..... . . 435 Jacking .
Page 541 INDEX 539 Transmission ......466 Unleaded Gasoline ..... . . 386 Automatic .
Page 542 540 INDEX Washing Vehicle ......469 Power ....... 38 Water Rear Vent .
Page 543 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 544 Chrysler LLC 81-026-0917 First Edition Printed in U.S.A.

Chrysler TOWN & COUNTRY 2009 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

Chapters

Related Manuals for Chrysler TOWN & COUNTRY 2009

Summary of Contents for Chrysler TOWN & COUNTRY 2009