Common Operation - VIETA HA3000BT User Manual

Common operation

1. To turn the unit on/off
When the unit is power Off, it may be switched On by
pressing any button except RELEASE button.
When the unit is switched On, press and hold
POWER button for more than 0.5 seconds, to
switchthe power off.
2. To select function mode
Press MODE button to change function mode as
follows:
-->RADIO --> CARD (after inserting SD card)
-->USB (after inserting USB stick)-->BT(in BT
connection mode)-->AUX-->
When there is no media (USB/CARD), that mode will
be skipped.
3. To adjust the volume level
Rotate VOL knob to adjust volume level during
playback.
4. To mute or resume sound
Press PWR/MUTE button to eliminate or resume
sound immediately during playback. To resume the
sound immediately, you can also press SEL button or
rotate VOL knob.
5. To set sound mode and menu
1). To set sound mode:
Press SEL button shortly and repeatedly to select
mode of VOL(volume), BASS(without preset DSP),
TRE (treble) (without preset DSP), MID, BAL (balance)
and FAD (fader) in the sequence and circulation. In
each mode, the waiting time is about 5 seconds, and
when the waiting time is over, it will return to the last
display mode.
After selecting a sound mode, use volume control to
set level of the selected soundmode.
2). To set menu:
Press SEL button and hold for more than 2 seconds
to turn on INVOL mode, then press SEL button
shortly and repeatedly to select DSP(adjust clock),
BEEP ON/OFF, TAVOL, EON ON/OFF, REG ON/OFF,
AF ON/OFF, TAON/OFF,EQ ON/OFF, LOUD ON/OFF,
LOC ON/OFF (in radio mode), STEREO/MONO(in
radio mode), AREA(USA/EUR) in radio mode)mode.
After selecting a desired item, use volume control to
set.
(1) TASEEK/TAALM:
TASEEK mode: when newly tuned station does
not receive TP information for 5 seconds, the
radio retunes to next station which has not the
same station(PI) as the last station, but has the
TP information. When TP information gets lost at
the current station for retune time which is set by
RETUNE SHORT(90 seconds) or RETUNE LONG
(150 seconds), the radio start to retune to next same
PI station. When same PI station is not received in 1
cyclic search, the radio retunes to next station with
TP information.
TA ALARMmode: when this mode is selected, any
automatic retune mode is not activated. Only double
beep sound(ALARM) is out-put. When newly tuned
station does not have TP information for 5 seconds,
beeps are sounded.
When TP information gets lost at the current station
for retune time, the beep sound is out-putted.
When newly tuned station has no RDS signal, PI
SEEK may be suppressed.
(2) PI SOUND/ PI MUTE:
PI SOUND mode: If a car is cruising between
buildings, an oscillation phenomenon may occur,
due to different PI codes being received from the
same AF.
PI MUTE mode: In above situation, the sound will be
muted for less than 1 second.
(3) RETUNE L / RETUNE S:
The initial time of automatic TAsearch or PI SEARCH
mode is selected.
When PI information is not received during retune
time, the radio start to retune to next same PI station.
When same PI station is not received during 1 cyclic
search, the radio goes to last
station and waits for 4-5 minutes until PI code is
received.
RETUNE L mode: selected as 150 seconds.
RETUNE S mode: selected as 90 seconds.
(4) MASK DPI/MASKALL:
MASK DPI mode: masked only the AF which has
different PI.
MASKALL mode: masked the AF which has different
PI and NO RDS signal with high field strength.
(5) BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any
key is pressed.
BEEP OFF mode: The beep sound is disabled.
(6) VOL LAST/VOL DEFA
VOL LAST: The volume level when switching off will
be restored with power On.
VOL DEFA: The volume level of the main unit after
power on is a constant value.
when selecting VOL DEFA item, press SEL button
to display AVOL , then you can pre-set the constant
volume level after power on with VOL control.
(7) CLK ON/OFF
CLK ON: Clock will always show on the display when
power is off.
13