Download Print this page

Heatstore HSXCA12X Installation And Operating Instructions

Combined storage and convector heater

Advertisement

Quick Links

HSXCA(X)
MODELS:
HSXCA12X 1.7KW/12kWh Storage and 1kW Convector
HSXCA18X 2.5kW/18kWh Storage and 1.5kW Convector
HSXCA24X 3.4kW/24kWh Storage and 2kW Convector
PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER
USE. NOTE ALSO THE INFORMATION GIVEN ON THE HEATER
The installation must be carried out by a trained competent personnel.
A means for disconnection must be incorporated in the fi xed wiring by a double pole switch with a contact separa-
tion of a minimum of 3mm and in accordance with the current IEE Wiring Regulations
The heater must not be installed immediately below a fi xed socket outlet.
The heater is not suitable for connection to a 30A ring circuit (24 hour peak supply).
Do not position the heater under windows where curtains can contact the heater casing.
WARNING - THE SURFACES ON THIS HEATER CAN BE HOT
This heater meets EN60335 safety requirements. However, any heater type becomes hot in normal operation.
Care must be taken to ensure that prolonged skin contact with the heater does not occur.
WHERE YOUNG CHILDREN, INFIRM PERSONS, OR THE AGED ARE PRESENT THIS APPLIANCE MUST
BE ADEQUATELY GUARDED. Contact your installer or manufacturer for further advice.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision for instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
This appliance is very heavy and must be securely fi xed to a wall. DO NOT UNDER ANY CIRCUMSTANCES
ATTEMPT TO MOVE OR REPOSITION THIS HEATER WITHOUT SEEKING EXPERT ADVICE.
To maintain stability, it is essential that the heater is placed on a level surface.
This heater must be installed where it is impossible for switches and other controls to be touched by a person
using a bath or shower.
IMPORTANT - Due to the newness of materials the heater will produce a slight smell for the fi rst few days of
operation. ROOMS MUST BE WELL VENTILATED AND YOUNG CHILDREN, CAGED BIRDS, OR PERSONS
WITH RESPIRATORY COMPLAINTS MUST NOT REMAIN IN CLOSE PROXIMITY TO THE HEATER DURING
THE FIRST 48 HOURS OF THE COMMISSIONING PERIOD.
IF, DURING ANY REASSEMBLY OF THE HEATER, A PART OF THE THERMAL INSULATION SHOWS DAMAGE
OR DETERIORATION WHICH MAY IMPAIR SAFETY, IT SHOULD BE REPLACED BY AN IDENTICAL PART.
INSTALLATION AND OPERATING
INSTRUCTIONS
COMBINED STORAGE AND
CONVECTOR HEATER
IMPORTANT
88962

Advertisement

loading

Summary of Contents for Heatstore HSXCA12X

  • Page 1 88962 HSXCA(X) COMBINED STORAGE AND CONVECTOR HEATER MODELS: HSXCA12X 1.7KW/12kWh Storage and 1kW Convector HSXCA18X 2.5kW/18kWh Storage and 1.5kW Convector HSXCA24X 3.4kW/24kWh Storage and 2kW Convector INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT PLEASE READ THIS LEAFLET CAREFULLY AND RETAIN FOR FURTHER USE.
  • Page 2: Installation Instructions

    INSTALLATION INSTRUCTIONS 3. Place the heater on its feet and in the desired position PREPARATION against the wall. Ensure the heater is based on a fi rm level surface at least 75mm from any end wall and at least 250mm below any shelf or similar projection.
  • Page 3 12. Fit the front layer of bricks again with the recess towards the element. The complete core will comprise: 12 - 2 x 4 Brick Columns 18 - 3 x 4 Brick Columns 24 - 4 x 4 Brick Columns 13.
  • Page 4: Safety Instructions

    Output Control to 1. With the control in © Heatstore All rights reserved. Material contained in this publication may not be reproduced in this position, the heater will take in less energy during the next whole or part, without prior permission in writing from Heatstore.

This manual is also suitable for:

Hsxca18xHsxca24x